EF Logo

Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing

Volvo/Mack Fuel delivery pressure fault codes

The fuel delivery pressure sensor measures the pressure of the low-pressure fuel supply before the injection system. A low reading starves the injectors.

FaultCheckMID 128PID 94FMI 7Volvo/Mack · Fuel delivery pressure
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PID 94 FMI 3 to MID 128 PID 94 FMI 18 are all about the fuel delivery pressure. None needs an immediate stop. Start with this check: replace or inspect the fuel filters first.

How urgent are they?

None of the 4 codes here means stop now; all 4 can wait until the shift ends, but find the cause before the next one.

  • Check soon4

What should I check first?

Replace or inspect the fuel filters first

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PID 94 FMI 3Fuel delivery pressure sensor signal high

    The low-pressure fuel sensor signal is above its valid range.· Shorted high
    Check soon

    Causes

    • Damaged pins or contacts in the fuel pressure sensor connector
    • Open circuit in the sensor wiring
    • Fuel pressure sensor failed

    Checks

    1. 1Read fuel delivery pressure live with the key on; a fixed value that ignores a primed system points to the sensor circuit
    2. 2Unplug the sensor and inspect the connector pins for corrosion or spread terminals
    3. 3Check 5 V supply, ground and signal continuity between the sensor plug and the ECM
    4. 4Test the signal wire for a short to a supply wire with the key off
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 128 PID 94 FMI 5Fuel delivery pressure sensor circuit open or low

    The fuel pressure sensor signal is low or open.· Open circuit
    Check soon

    Causes

    • Damaged contacts in the harness or connector
    • Faulty fuel pressure sensor
    • Broken signal or supply wire

    Checks

    1. 1Compare live fuel pressure with a mechanical gauge at the filter housing before blaming the sensor
    2. 2Unplug the sensor and test for 5 V supply at the harness plug
    3. 3Check continuity of the signal wire to the ECM with the key off
    4. 4Inspect the connector pins and seals for fuel or water ingress
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 PID 94 FMI 7Fuel delivery pressure dropping, supply not responding

    Measured fuel supply pressure has fallen and the fuel system is not responding the way the ECM expects.· Part or controller
    Check soon

    Causes

    • Clogged fuel filter or water separator
    • Leaking fuel line or loose fitting letting air in
    • Weak or failing fuel supply pump
    • Faulty fuel pressure sensor reading wrongly

    Checks

    1. 1Read fuel pressure live at idle and at full load and note where it drops
    2. 2Change or check the primary and secondary fuel filters first, and check how long since they were serviced
    3. 3Inspect the supply side for leaks and air; look for air bubbles in a clear line if fitted
    4. 4Test pump output pressure at the filter head with a mechanical gauge
    5. 5Check the fuel tank pickup and any suction-side restriction
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Volvo/Mack MID 128 PID 94 FMI 18Fuel delivery pressure moderately low

    Supply pressure has fallen to a moderately low level.· Real condition
    Check soon

    Causes

    • Partly clogged fuel filter
    • Fuel leak or loose fitting on the suction side
    • Fuel pump losing output
    • Fuel pressure sensor reading low

    Checks

    1. 1Compare live fuel pressure with a mechanical gauge at the filter housing during a load test
    2. 2Replace the fuel filters if their service age is unknown
    3. 3Check the fuel lines and fittings for seepage and air entry
    4. 4Check the fuel level in the tank and the pickup for blockage
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Replace or inspect the fuel filters first
  2. 2Test the fuel supply pressure with a mechanical gauge at idle and under load and compare it with the sensor
  3. 3Check the fuel lines for air leaks and kinks
  4. 4Check the sensor connector and signal wire

Causes

  • Clogged fuel filter
  • Weak fuel transfer pump or air in the fuel
  • Pressure sensor or harness fault

When to stop

You'll notice: The engine loses power, cranks long or stalls, and a check lamp comes on.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.