Volvo/Mack · MID 130 transmission ECU
Volvo/Mack Fault Code MID 130 PSID 27 FMI 12
Clutch slipping
What does Volvo/Mack code MID 130 PSID 27 FMI 12 mean?
The clutch cannot transfer the requested torque without slipping. The control unit reduces engine torque so it does not slip any further. Urgency: check soon - the machine may derate or limit a function. Check first: check the clutch wear value in the scan tool for damage, corrosion or looseness.
- MID 130
- Which control unit reports it
- PSID 27
- Maker component at fault
- FMI 12
- Bad intelligent device or component
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check the clutch wear value in the scan tool for damage, corrosion or looseness
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- Worn clutch
- Oil contamination on the clutch
- Weak clutch pressure plate
How it failed
You'll notice: Yellow lamp sent and the engine torque is reduced so the clutch does not continue to slip.
Part or controllerRead from FMI 12: bad intelligent device or component
The controller reports a part, module or its software as faulty or not responding.
- Meter test
- Check power and ground at the module connector with the key on, then its fuses.
- Good result
- Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Clutch operation
- MID 130 PSID 27 FMI 0Clutch disengages unintentionallyReal conditionCheck soon
- MID 130 PSID 27 FMI 11Clutch dragOtherCheck soon
- MID 130 PSID 27 FMI 12Clutch slippingPart or controllerCheck soon
- MID 130 PSID 27 FMI 14Clutch cannot disengage - engine shut downOtherStop now
Other Volvo/Mack codes: MID 130 transmission ECU
- MID 130 PID 33 FMI 2Clutch position sensor signals disagree
- MID 130 PID 33 FMI 3Clutch position sensor signal shorted high
- MID 130 PID 33 FMI 5Clutch position sensor open circuit
- MID 130 PID 33 FMI 13Clutch position sensor not calibrated
- MID 130 PID 36 FMI 0Clutch wear above service limit
- MID 130 PID 37 FMI 0Transmission air pressure too high
Related on Equipments Finder
Source
This source lists MID 130 PSID 27 FMI 12 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack CHU, CXU, GU and TD trucks with the mDRIVE automated transmission (MID 130 transmission control unit).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
