Volvo/Mack · MID 128 engine ECU - module, data link and power
Volvo/Mack Fault Code MID 128 SID 231 FMI 2
SAE J1939 data link (CAN 1) circuit fault
What does Volvo/Mack code MID 128 SID 231 FMI 2 mean?
The engine ECM detected a problem on the J1939 CAN 1 data link. Mack lists the CAN high or low shorted to positive or ground, or open. Urgency: check soon - the machine may derate or limit a function. Check first: measure resistance across the CAN high and low pins at the diagnostic connector with the key off; the pair should read about 60 ohms.
- MID 128
- Which control unit reports it
- SID 231
- Component at fault
- FMI 2
- Erratic or incorrect data
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Measure resistance across the CAN high and low pins at the diagnostic connector with the key off; the pair should read about 60 ohms
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- CAN high or low shorted to positive
- CAN high or low shorted to ground
- CAN high or low circuit open
- Damaged connector on the data link harness
How it failed
You'll notice: MIL lit and several modules can lose communication, which can show as missing gauges, no cruise or limited engine power.
Erratic or implausibleRead from FMI 2: erratic or incorrect data
The reading jumps, drifts or disagrees with the sensors around it.
- Meter test
- Watch the live value on the service tool while you flex the harness and tap the connector.
- Good result
- A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Other Volvo/Mack codes: MID 128 engine ECU - module, data link and power
- MID 128 PSID 229 FMI 9SAE J1939 data link 2 - lost communication with aftertreatment module
- MID 128 SID 39 FMI 3Starter relay output shorted high
- MID 128 SID 39 FMI 5Starter relay circuit open
- MID 128 PID 158 FMI 1ECM battery voltage too low
- MID 128 PID 158 FMI 3ECM battery voltage too high
- MID 128 PSID 161 FMI 2Vehicle identification number (VIN) missing
- MID 128 PSID 201 FMI 9Message from instrument cluster missing
- MID 128 PSID 229 FMI 2SAE J1939 data link 2 circuit shorted or open
Related on Equipments Finder
Source
This source lists MID 128 SID 231 FMI 2 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
