Volvo/Mack · MID 128 engine ECU - module, data link and power
Volvo/Mack Fault Code MID 128 PSID 229 FMI 9
SAE J1939 data link 2 - lost communication with aftertreatment module
What does Volvo/Mack code MID 128 PSID 229 FMI 9 mean?
The engine ECM no longer receives messages from the aftertreatment control module on the second J1939 data link (SPN 1231). Urgency: check soon - the machine may derate or limit a function. Check first: first check if the fault is active; Mack says an inactive code counted in multiples of three on 2010-2013 MP7/MP8 may only need an engine software update.
- MID 128
- Which control unit reports it
- PSID 229
- Maker component at fault
- FMI 9
- Abnormal update rate
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
First check if the fault is active; Mack says an inactive code counted in multiples of three on 2010-2013 MP7/MP8 may only need an engine software update
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Damaged CAN 2 harness or connector between the engine ECM and the aftertreatment module
- DEF pump or aftertreatment DEF module pulling down the data link
- Aftertreatment control module failure
- Low supply voltage to the aftertreatment module
How it failed
You'll notice: MIL and yellow lamp lit and no DEF dosing.
Lost messageRead from FMI 9: abnormal update rate
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: J1939 data link 2 (aftertreatment)
- MID 128 PSID 229 FMI 2SAE J1939 data link 2 circuit shorted or openErratic or implausibleCheck soon
- MID 128 PSID 229 FMI 9SAE J1939 data link 2 - lost communication with aftertreatment moduleLost messageCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - module, data link and power
- MID 128 SID 231 FMI 2SAE J1939 data link (CAN 1) circuit fault
- MID 128 SID 39 FMI 3Starter relay output shorted high
- MID 128 SID 39 FMI 5Starter relay circuit open
- MID 128 PID 158 FMI 1ECM battery voltage too low
- MID 128 PID 158 FMI 3ECM battery voltage too high
- MID 128 PSID 161 FMI 2Vehicle identification number (VIN) missing
- MID 128 PSID 201 FMI 9Message from instrument cluster missing
Related on Equipments Finder
Source
This source lists MID 128 PSID 229 FMI 9 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
