EF Logo

Volvo/Mack · MID 128 engine ECU - module, data link and power

Volvo/Mack Engine ECU battery voltage fault codes

The engine ECU monitors its supply voltage. Low or high voltage causes unreliable operation and logs these codes.

FaultCheckMID 128PID 158FMI 1Volvo/Mack · Engine ECU battery voltage
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PID 158 FMI 1 and MID 128 PID 158 FMI 3 are all about the engine ECU battery voltage. None needs an immediate stop. Start with this check: measure the battery voltage at rest and cranking.

How urgent are they?

None of the 2 codes here means stop now; all 2 can wait until the shift ends, but find the cause before the next one.

  • Check soon2

What should I check first?

Measure the battery voltage at rest and cranking

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PID 158 FMI 1ECM battery voltage too low

    The battery voltage seen at the engine ECM is below the normal range.· Real condition
    Check soon

    Causes

    • Weak or discharged batteries
    • Charging system fault, such as a failed alternator
    • Poor ground connection
    • Corroded battery cables

    Checks

    1. 1Measure battery voltage at rest and while cranking
    2. 2Check alternator output with the engine running
    3. 3Clean and tighten battery cables and chassis ground connections
    4. 4Check voltage at the ECM connector with the key on
    5. 5Load test both batteries and check the terminals, because a weak battery lets the voltage collapse on cranking
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PID 158 FMI 3ECM battery voltage too high

    The battery voltage seen at the engine ECM is above the normal range.· Shorted high
    Check soon

    Causes

    • Charging system fault such as a failed voltage regulator
    • External charger connected
    • Engine control module fault

    Checks

    1. 1Measure battery voltage with the engine running; it should not run far above normal charging voltage
    2. 2Disconnect any external charger or booster and recheck
    3. 3Check the alternator regulator operation for damage, corrosion or looseness
    4. 4Compare the voltage at the ECM connector with the battery voltage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

Shared checks

Checks, in order

  1. 1Measure the battery voltage at rest and cranking
  2. 2Check the alternator output with the engine running and look for a voltage that stays in the normal range
  3. 3Clean the battery terminals and ground straps
  4. 4Check the ECU power connector for corrosion and heat marks, and measure the voltage drop under load

Causes

  • Weak batteries or loose terminals
  • Charging fault
  • Corroded ECU power connection

When to stop

You'll notice: The engine may stall or restart, the lamps flicker, and several other codes may appear at the same time.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.