Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing
Volvo/Mack Fault Code MID 128 PID 97 FMI 0
Water in fuel detected
What does Volvo/Mack code MID 128 PID 97 FMI 0 mean?
The water-in-fuel sensor in the fuel filter or water separator reports water. The ECM treats it as real contamination, because water in the injection system can damage the injectors and high pressure pump. Urgency: check soon - the machine may derate or limit a function. Check first: drain the water separator and look at what comes out.
- MID 128
- Which control unit reports it
- PID 97
- Parameter at fault
- FMI 0
- Data above normal, most severe
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Drain the water separator and look at what comes out
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- Water collected in the fuel filter or separator from condensation or a contaminated fill
- Water separator not drained at the service interval
- Contaminated fuel from the tank or a supplier
How it failed
You'll notice: A water-in-fuel lamp or message may appear.
Real conditionRead from FMI 0: data above normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Water in fuel sensor
- MID 128 PID 97 FMI 0Water in fuel detectedReal conditionCheck soon
- MID 128 PID 97 FMI 3Water in fuel sensor circuit shorted high or openShorted highCheck soon
- MID 128 PID 97 FMI 4Water in fuel sensor circuit shorted to groundShorted lowCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - fuel, injectors and timing
- MID 128 SID 1 FMI 3Injector cylinder 1 circuit shorted high
- MID 128 SID 1 FMI 5Injector cylinder 1 circuit open or shorted to ground
- MID 128 SID 1 FMI 7Injector cylinder 1 balancing above limit
- MID 128 SID 1 FMI 8Injector cylinder 1 misfire detected
- MID 128 SID 1 FMI 13Injector cylinder 1 out of calibration
- MID 128 SID 2 FMI 5Injector cylinder 2 circuit open or shorted
Related on Equipments Finder
Source
This source lists MID 128 PID 97 FMI 0 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
