John Deere fault codes
John Deere excavators show a controller prefix, a number and a failure mode on the monitor - ECU 000100.01 for the engine, MCZ for the main controller, DSZ for the monitor itself.
407 codes in 22 families31 stop now, 364 check soon, 12 info
407 John Deere codes - type a code, or a word from the problem.
Covers Excavators, Skid steers.
Where to look
- 01Turn the key on and open the monitor's diagnostic/fault screen.
- 02Note the controller prefix, number and mode.
- 03Check whether codes are active or stored.
- 04After repair, clear the codes and retest.
How to read John Deere fault codes, in full
- Turn the key on and open the monitor's diagnostic/fault screen.
- Note the controller prefix (ECU, MCZ, DSZ), number and mode.
- Check whether codes are active or stored.
- After repair, clear the codes and retest.
How urgent is a John Deere code?
- Stop now31 codes
- Shut down and fix before working on. Running on risks damage or the machine locks out.
- Check soon364 codes
- The machine may derate or limit a function. Find the cause before the next shift.
- Information12 codes
- A reminder or status message. Nothing is failing yet.
Pick your system
Find the part of the machine, then the family your code belongs to.
- Code range
- The first and last code in the family, as the machine shows them.
- Codes
- How many codes the family holds; each is explained on its page.
- Severity mix
- The share of stop, check and info codes. The dot after it is the most urgent one in the family.
Main controller (MCZ) - pressure sensors52 codes
- Pump pressure and hydraulic oil temperature sensorsMCZ 11200.03 – MCZ 15011.0418 codes
- Boom, arm and bucket pressure sensorsMCZ 11302.03 – MCZ 11998.0414 codes
- Swing, travel and attachment pressure sensorsMCZ 11301.03 – MCZ 11942.048 codes
- Pilot and counterweight pressure sensorsMCZ 11943.03 – MCZ 11990.0412 codes
Main controller (MCZ) - solenoids63 codes
Main controller (MCZ) - attachment levers24 codes
Engine control unit (ECU) - Cooling23 codes
Engine control unit (ECU) - PowerTech engine44 codes
Main controller (MCZ) - engine21 codes
Main controller (MCZ) - communication20 codes
Engine control unit (ECU) - Communication21 codes
Main controller (MCZ) - internal18 codes
Monitor controller (DSZ) - alarms24 codes
Main controller (MCZ) - alarms14 codes
Engine control unit (ECU) - Exhaust13 codes
Basic control unit (BCU) - tractor22 codes
Armrest control unit (ACU) - tractor18 codes
Transmission control unit (TCU) - tractor19 codes
Climate controller (ACF) - sensors and controls11 codes
Most searched John Deere codes
- ECU 000097.03Water in fuel sensor voltage high
- ECU 000097.04Water in fuel separator full
- ECU 000100.01Low engine oil pressure
- ECU 000107.00Air filter differential pressure high
- ECU 000110.00Coolant temperature high
- ECU 000111.01Coolant level low
- ECU 000158.01Battery voltage low
- ECU 000190.00Engine speed high
- ECU 001110.31Engine protection shutdown
- ECU 001639.01Fan speed low
- ECU 003701.14Parked exhaust filter cleaning requested
- MCZ 11004.02MCZ CAN communication error
- MCZ 11006.02Engine controller communication error
- MCZ 11200.03Pump 1 delivery pressure sensor (B35) signal high
- MCZ 11200.04Pump 1 delivery pressure sensor (B35) signal low
- MCZ 11202.03Pump 2 delivery pressure sensor (B37) signal high
- MCZ 11202.04Pump 2 delivery pressure sensor (B37) signal low
- MCZ 11302.03Boom up pressure sensor (B30) signal high
- MCZ 11302.04Boom up pressure sensor (B30) signal low
- MCZ 11400.02Pump 2 flow rate limit solenoid (SB), feedback abnormal
- MCZ 11457.022-speed activation solenoid not detected
- MCZ 11458.02Selector valve solenoid not detected
- MCZ 11901.03Hydraulic oil temperature sensor (B40) high
- MCZ 11901.04Hydraulic oil temperature sensor (B40) low
- MCZ 20010.02Exhaust filter abnormal
- MCZ 20012.02Line filter restriction alarm
- MCZ 20062.02Hydraulic oil temperature alarm
- DSZ 20102.02Engine oil pressure alarm
- DSZ 20110.02Fuel filter restriction alarm
Quick answers
How do I read John Deere fault codes?
Turn the key on and open the monitor's diagnostic/fault screen. Note the controller prefix (ECU, MCZ, DSZ), number and mode.
Which John Deere codes mean stop now?
31 of the 407 John Deere codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example ECU 000100.01, ECU 000110.00, ECU 000111.01, ECU 000190.00. 364 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.
What should I check first on a John Deere code?
Most John Deere codes here (76 of 407) read as lost message: a module stopped hearing another on the data link, or the data came late or garbled. First test, as general workshop practice: key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Which John Deere codes are looked up most?
ECU 000097.03 (water in fuel sensor voltage high), ECU 000097.04 (water in fuel separator full), ECU 000100.01 (low engine oil pressure), ECU 000107.00 (air filter differential pressure high), ECU 000110.00 (coolant temperature high). Each page gives the meaning, the likely causes and the checks.
Sources
Every code was read from these documents and written in our own words.
Other makers
Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.
Post a request