John Deere · Engine control unit (ECU) - PowerTech engine
John Deere Fault Code ECU 000097.03
Water in fuel sensor voltage high
What does John Deere code ECU 000097.03 mean?
The ECU reads the water-in-fuel sensor signal at its high limit, usually a short or fault in the sensor circuit. Urgency: check soon - the machine may derate or limit a function. Check first: drain the water separator bowl first; if the warning stays after the bowl is dry, suspect the circuit and not the fuel.
- ECU
- Which controller reports it
- 000097
- Water in fuel indicator
- .03
- Voltage above normal or shorted high
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Drain the water separator bowl first; if the warning stays after the bowl is dry, suspect the circuit and not the fuel
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- Water-in-fuel sensor wire shorted to its supply inside the filter head connector
- Sensor failed with its output stuck high
- Corroded or wet sensor plug bridging the pins
- Water-in-fuel circuit open at the ground side, letting the signal float high
How it failed
You'll notice: The ECU reads the water-in-fuel sensor at its high limit, which points to a fault in the sensor circuit and not necessarily water.
Shorted highRead from how the source describes the code
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine, overheat, fuel and water alarms on the monitor
- ECU 000097.03Water in fuel sensor voltage highShorted highCheck soon
- ECU 000097.04Water in fuel separator fullLost messageCheck soon
- ECU 001110.31Engine protection shutdownOtherStop now
- DSZ 13310.03Shorted circuit in coolant temperature sensorShort circuitCheck soon
- ICZ 13310.03Shorted circuit in coolant temperature sensorShort circuitCheck soon
- ICZ 13334.02Radiator coolant errorOtherCheck soon
- DSZ 20100.02Overheat alarmReal conditionCheck soon
- DSZ 20101.02Engine warning alarmLost messageCheck soon
- ICZ 20101.02Engine warning alarmLost messageCheck soon
Show the other 15 codesHide the other codes
- DSZ 20102.02Engine oil pressure alarmLost messageStop now
- ICZ 20102.02Engine oil pressure alarmLost messageStop now
- DSZ 20107.02Water separator alarmLost messageCheck soon
- DSZ 20110.02Fuel filter restriction alarmReal conditionCheck soon
- ICZ 20110.02Fuel filter restriction alarmReal conditionCheck soon
- DSZ 20114.02Overheat alarmReal conditionCheck soon
- ICZ 20114.02Overheat alarmReal conditionCheck soon
- DSZ 20142.02Intake air temperature alarmReal conditionCheck soon
- ICZ 20142.02Intake air temperature alarmReal conditionCheck soon
- DSZ 20145.02Boost temperature increase alarmOtherCheck soon
- ICZ 20145.02Boost temperature increase alarmOtherCheck soon
- DSZ 20146.02Fuel temperature increase alarmLost messageCheck soon
- ICZ 20146.02Fuel temperature increase alarmLost messageCheck soon
- DSZ 20149.02EGR gas temperature alarmReal conditionCheck soon
- ICZ 20149.02EGR gas temperature alarmReal conditionCheck soon
Other John Deere codes: Engine control unit (ECU) - PowerTech engine
- ECU 000100.01Low engine oil pressure
- ECU 000100.03Engine oil pressure input voltage high
- ECU 000100.04Engine oil pressure signal voltage low
- ECU 000100.18Engine power limited by oil pressure
- ECU 000100.31Oil pressure sensed with engine stopped
- ECU 000102.02Manifold air pressure sensor trouble
- ECU 000102.03Manifold air pressure sensor fault
Related on Equipments Finder
Source
Inside the Yard - John Deere fault codes list (ECU engine codes)
This source lists ECU 000097.03 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere PowerTech engines; code list comes from tractor-based sources, confirm for your machine.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
