John Deere · Engine control unit (ECU) - Engine
John Deere Fault Code ECU 001110.31
Engine protection shutdown
What does John Deere code ECU 001110.31 mean?
The engine protection system shut the engine down, so the engine stops and the operator may see a protection shutdown message. The actual cause is another condition logged at the same time. Urgency: stop now - shut down and fix before working on. Check first: read all active and stored ECU codes to find the condition that caused the shutdown.
- ECU
- Which controller reports it
- 001110
- What is at fault
- .31
- Condition exists
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Read all active and stored ECU codes to find the condition that caused the shutdown
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- Low oil pressure or high coolant temperature that triggered the shutdown
- Engine overspeed or another engine protection fault
- Failed sensor feeding a false value to the protection logic
- Coolant level too low
How it failed
You'll notice: The engine protection system shut the engine down.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine, overheat, fuel and water alarms on the monitor
- ECU 000097.03Water in fuel sensor voltage highShorted highCheck soon
- ECU 000097.04Water in fuel separator fullLost messageCheck soon
- ECU 001110.31Engine protection shutdownOtherStop now
- DSZ 13310.03Shorted circuit in coolant temperature sensorShort circuitCheck soon
- ICZ 13310.03Shorted circuit in coolant temperature sensorShort circuitCheck soon
- ICZ 13334.02Radiator coolant errorOtherCheck soon
- DSZ 20100.02Overheat alarmReal conditionCheck soon
- DSZ 20101.02Engine warning alarmLost messageCheck soon
- ICZ 20101.02Engine warning alarmLost messageCheck soon
Show the other 15 codesHide the other codes
- DSZ 20102.02Engine oil pressure alarmLost messageStop now
- ICZ 20102.02Engine oil pressure alarmLost messageStop now
- DSZ 20107.02Water separator alarmLost messageCheck soon
- DSZ 20110.02Fuel filter restriction alarmReal conditionCheck soon
- ICZ 20110.02Fuel filter restriction alarmReal conditionCheck soon
- DSZ 20114.02Overheat alarmReal conditionCheck soon
- ICZ 20114.02Overheat alarmReal conditionCheck soon
- DSZ 20142.02Intake air temperature alarmReal conditionCheck soon
- ICZ 20142.02Intake air temperature alarmReal conditionCheck soon
- DSZ 20145.02Boost temperature increase alarmOtherCheck soon
- ICZ 20145.02Boost temperature increase alarmOtherCheck soon
- DSZ 20146.02Fuel temperature increase alarmLost messageCheck soon
- ICZ 20146.02Fuel temperature increase alarmLost messageCheck soon
- DSZ 20149.02EGR gas temperature alarmReal conditionCheck soon
- ICZ 20149.02EGR gas temperature alarmReal conditionCheck soon
Other John Deere codes: Engine control unit (ECU) - Engine
Related on Equipments Finder
Source
Excavator Fault Codes - John Deere excavators fault codes list (MCZ/ECU/DSZ)
This source lists ECU 001110.31 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere G-series excavators (210G/210GLC and 350G class) with MCZ main controller; confirm against serial number.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
