John Deere · Monitor controller (DSZ) - alarms
John Deere Fault Code DSZ 20110.02
Fuel filter restriction alarm
What does John Deere code DSZ 20110.02 mean?
The fuel filter looks restricted, so the fuel supply may not keep up under load. Diagnose ECU code 000094.17 per the engine manual. Urgency: check soon - the machine may derate or limit a function. Check first: replace the fuel filter and bleed the system following the engine manual.
- DSZ
- Which controller reports it
- 20110
- What is at fault
- .02
- How it failed
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Replace the fuel filter and bleed the system following the engine manual
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- Fuel filter blocked
- Fuel supply line kinked
- Fuel pressure sensor faulty
- Contaminated fuel
How it failed
You'll notice: The fuel filter looks restricted.
Real conditionRead from how the source describes the code
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine, overheat, fuel and water alarms on the monitor
8 other codes on this part are also real condition (DSZ 20100.02, ICZ 20110.02, DSZ 20114.02, ICZ 20114.02 and more). When they show together, start at the wiring and connector they share.
- ICZ 20101.02Engine warning alarmLost messageCheck soon
- DSZ 20102.02Engine oil pressure alarmLost messageStop now
- ICZ 20102.02Engine oil pressure alarmLost messageStop now
- DSZ 20107.02Water separator alarmLost messageCheck soon
- DSZ 20110.02Fuel filter restriction alarmReal conditionCheck soon
- ICZ 20110.02Fuel filter restriction alarmReal conditionCheck soon
- DSZ 20114.02Overheat alarmReal conditionCheck soon
- ICZ 20114.02Overheat alarmReal conditionCheck soon
- DSZ 20142.02Intake air temperature alarmReal conditionCheck soon
Show the other 15 codesHide the other codes
- ECU 000097.03Water in fuel sensor voltage highShorted highCheck soon
- ECU 000097.04Water in fuel separator fullLost messageCheck soon
- ECU 001110.31Engine protection shutdownOtherStop now
- DSZ 13310.03Shorted circuit in coolant temperature sensorShort circuitCheck soon
- ICZ 13310.03Shorted circuit in coolant temperature sensorShort circuitCheck soon
- ICZ 13334.02Radiator coolant errorOtherCheck soon
- DSZ 20100.02Overheat alarmReal conditionCheck soon
- DSZ 20101.02Engine warning alarmLost messageCheck soon
- ICZ 20142.02Intake air temperature alarmReal conditionCheck soon
- DSZ 20145.02Boost temperature increase alarmOtherCheck soon
- ICZ 20145.02Boost temperature increase alarmOtherCheck soon
- DSZ 20146.02Fuel temperature increase alarmLost messageCheck soon
- ICZ 20146.02Fuel temperature increase alarmLost messageCheck soon
- DSZ 20149.02EGR gas temperature alarmReal conditionCheck soon
- ICZ 20149.02EGR gas temperature alarmReal conditionCheck soon
Other John Deere codes: Monitor controller (DSZ) - alarms
Related on Equipments Finder
Source
Excavator Fault Codes - John Deere excavators fault codes list (MCZ/ECU/DSZ)
This source lists DSZ 20110.02 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere G-series excavators (210G/210GLC and 350G class) with MCZ main controller; confirm against serial number.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
