EF Logo

John Deere · Engine control unit (ECU) - PowerTech engine

John Deere Engine oil pressure, boost, turbo, EGR and fuel rail fault codes

These ECU codes cover the pressure and air-path parts of the engine. Oil pressure and fuel rail pressure sensors, the manifold air (boost) pressure sensor, the turbocharger speed sensor, the EGR valve position, the injector circuits and the barometric pressure sensor each have their own codes: a value out of range, a sensor signal high or low, or a circuit short.

FaultStopECU 000100.01John Deere · Engine oil pressure, boost, turbo, EGR and fuel rail
Code shows hereFAULTECU 000100.01

Where this code shows

Turn the key on and open the monitor's diagnostic/fault screen.

What do these codes mean?

John Deere codes ECU 000027.03 to ECU 002790.16 are all about the engine oil pressure, boost, turbo, EGR and fuel rail. The most common failure type is shorted high (3 of 24); 1 needs an immediate stop. Start with this check: read all active ECU codes first and note which sensor or circuit the code names.

How urgent are they?

1 of 24 codes here means stop now; the other 23 can wait until the shift ends, but find the cause before the next one.

  • Stop now1
  • Check soon23

What should I check first?

Read all active ECU codes first and note which sensor or circuit the code names

Shared checks

24 of 24

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • John Deere ECU 000027.03EGR valve position signal high

    The ECU reads the EGR valve position signal as high, which points to a short to supply voltage in the position circuit.· Shorted high
    Check soon

    Causes

    • EGR position signal wire shorted to the 5 V supply wire in the engine harness
    • EGR valve position sensor failed high inside the actuator
    • Open ground in the EGR valve circuit, letting the signal float up

    Checks

    1. 1Unplug the EGR valve and measure the position signal voltage at the harness with the key on
    2. 2Check the EGR valve ground wire for continuity back to the ECU
    3. 3Inspect the EGR connector for water, soot and corrosion
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • John Deere ECU 000027.04EGR valve position signal low

    The ECU reads the EGR valve position signal as low, which points to a short to ground or an open circuit in the position circuit.· Shorted low
    Check soon

    Causes

    • EGR position signal wire shorted to ground or open between the valve and the ECU
    • No 5 V supply reaching the EGR position sensor
    • EGR valve position sensor failed low

    Checks

    1. 1Check for 5 V at the EGR connector supply pin with the key on and the valve unplugged
    2. 2Check the position signal wire for continuity and for a short to ground with the ECU end disconnected
    3. 3Check the EGR connector for a loose or pushed-back pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • John Deere ECU 000027.07EGR valve actuator fault

    The ECU sees that the commanded and actual EGR valve positions do not match.· Other
    Check soon

    Causes

    • EGR valve jammed by soot or carbon so it cannot reach the commanded position
    • EGR actuator motor weak or failing
    • Loose or damaged valve linkage or position magnet

    Checks

    1. 1Remove the EGR valve and inspect it for soot build-up and a stuck plate or shaft
    2. 2Command the valve with the service tool and watch whether it follows the command smoothly
    3. 3Check the actuator wiring and connector for damage and moisture
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 000100.01Low engine oil pressure

    The ECU sees engine oil pressure below the limit.· Lost message
    Stop now

    Causes

    • Engine oil level too low
    • Oil diluted with fuel or coolant, or the wrong grade of oil
    • Worn bearings or a weak oil pump
    • Oil pressure sensor reading wrong or its wiring faulty

    Checks

    1. 1Stop the engine at once and check the oil level and condition on the dipstick
    2. 2Fit a mechanical gauge at the oil pressure test port and compare it with the manual figure
    3. 3Smell and feel the oil for fuel or coolant contamination
    4. 4Check the oil pressure sensor connector and wiring for damage
    5. 5Do not run the engine until the real pressure is confirmed
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere ECU 000100.03Engine oil pressure input voltage high

    The controller reads the engine oil pressure sensor signal above its normal range, so it cannot use the value and the function that depends on it runs on a fallback or is switched off.· Shorted high
    Check soon

    Causes

    • Signal wire of the engine oil pressure sensor shorted to the 5 V supply or to battery voltage
    • Open return (ground) wire at the engine oil pressure sensor, which lets the signal float high
    • The engine oil pressure sensor failed internally with a stuck high output

    Checks

    1. 1Unplug the engine oil pressure sensor and, key on, measure the harness signal pin: a value near 5 V points to a harness short or a controller fault rather than the part
    2. 2Check continuity of the engine oil pressure sensor return wire to the controller sensor ground with both ends disconnected
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • John Deere ECU 000100.04Engine oil pressure signal voltage low

    The controller reads the engine oil pressure sensor signal below its normal range, so it cannot use the value and the function that depends on it runs on a fallback or is switched off.· Shorted low
    Check soon

    Causes

    • Signal wire of the engine oil pressure sensor shorted to ground
    • Broken or unplugged 5 V supply wire to the engine oil pressure sensor
    • The engine oil pressure sensor failed internally with a stuck low output

    Checks

    1. 1With the engine oil pressure sensor unplugged and the key on, check for the 5 V supply on its harness plug; no supply means a broken feed wire or a faulty controller output
    2. 2Measure the signal wire to ground with both ends disconnected; a very low resistance means a short to ground in the harness
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • John Deere ECU 000100.18Engine power limited by oil pressure

    The engine is derated because of low oil pressure.· Other
    Check soon

    Causes

    • Oil pressure lower than normal at load from a worn pump or bearings
    • Oil level a little low or the oil too thin from heat or dilution
    • Blocked oil filter or a stuck relief valve

    Checks

    1. 1Check the oil level and oil condition and top up if needed
    2. 2Check the oil pressure with a mechanical gauge at idle and at rated speed
    3. 3Replace the engine oil filter if it is overdue, as a blocked filter lowers the pressure at the gallery
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 000100.31Oil pressure sensed with engine stopped

    The controller has set a condition code for the engine oil pressure sensor: the state it monitors exists, so it is telling the operator or the technician rather than reporting a broken part.· Other
    Check soon

    Causes

    • The real condition behind the engine oil pressure sensor is present
    • A related component or circuit that causes the condition
    • The message or reminder was not reset after the earlier service

    Checks

    1. 1Confirm on the machine that the condition behind the engine oil pressure sensor is real and act on it
    2. 2Read all other codes active at the same time, since this one is often a consequence of another fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 000102.02Manifold air pressure sensor trouble

    The controller sees an erratic, invalid or out-of-step signal from the manifold air pressure sensor, so it cannot rely on that input.· Erratic or implausible
    Check soon

    Causes

    • Intermittent connection at the manifold air pressure sensor plug or in its harness
    • Chafed wire that touches ground only when the machine moves
    • The manifold air pressure sensor wearing out or failing intermittently

    Checks

    1. 1Wiggle the manifold air pressure sensor harness and plug with the key on while watching the live value for jumps or dropouts
    2. 2Compare the live reading with the machine state (stopped, idling, working) to see when it goes wrong
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • John Deere ECU 000102.03Manifold air pressure sensor fault

    The ECU sees the intake manifold pressure sensor signal above its normal range, which means a fault in the sensor or its circuit.· Other
    Check soon

    Causes

    • Manifold pressure sensor signal wire shorted to the 5 V supply
    • Sensor failed high or blocked by soot
    • Open sensor ground wire

    Checks

    1. 1Unplug the sensor and measure the signal voltage at the harness with the key on
    2. 2Check the sensor ground wire continuity to the ECU
    3. 3Inspect the sensor and its connector for soot, oil and water
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 000102.04Manifold air pressure signal voltage low

    The controller reads the manifold air pressure sensor signal below its normal range, so it cannot use the value and the function that depends on it runs on a fallback or is switched off.· Shorted low
    Check soon

    Causes

    • Signal wire of the manifold air pressure sensor shorted to ground
    • Broken or unplugged 5 V supply wire to the manifold air pressure sensor
    • The manifold air pressure sensor failed internally with a stuck low output

    Checks

    1. 1With the manifold air pressure sensor unplugged and the key on, check for the 5 V supply on its harness plug; no supply means a broken feed wire or a faulty controller output
    2. 2Measure the signal wire to ground with both ends disconnected; a very low resistance means a short to ground in the harness
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • John Deere ECU 000103.00Turbo speed too high

    The ECU sees turbocharger speed above the limit.· Shorted high
    Check soon

    Causes

    • Restricted air filter or exhaust raising the turbo speed
    • Turbo speed sensor reading wrongly
    • Operating the machine at altitude or in conditions above the engine rating

    Checks

    1. 1Check the air filter and the exhaust for restriction
    2. 2Check the turbo speed sensor and its wiring for damage, since a false reading looks like overspeed
    3. 3Read the other ECU codes for boost, intake pressure and air temperature faults
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • John Deere ECU 000103.05Turbocharger speed sensor low

    The controller detects an open circuit on the turbocharger speed sensor, meaning the circuit is broken or the part is disconnected, so its signal is lost.· Open circuit
    Check soon

    Causes

    • Unplugged connector or a terminal pushed out of the turbocharger speed sensor plug
    • Broken wire inside the harness to the turbocharger speed sensor
    • Open element inside the turbocharger speed sensor itself

    Checks

    1. 1Inspect the turbocharger speed sensor plug for pushed-back terminals, corrosion or a plug that is not fully seated
    2. 2Measure continuity of the wires from the turbocharger speed sensor plug to the controller with both ends disconnected
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • John Deere ECU 000103.06Turbocharger speed power high

    The controller detects a short circuit on the turbocharger speed sensor, so the circuit draws too much current or the signal is pulled to a fixed level.· Short circuit
    Check soon

    Causes

    • Wire to the turbocharger speed sensor chafed through and touching ground or a supply wire
    • Water or oil inside the turbocharger speed sensor connector bridging pins
    • Internal short inside the turbocharger speed sensor

    Checks

    1. 1Unplug the turbocharger speed sensor and see whether the code changes from a short to an open; if it does, the part is the likely culprit
    2. 2Measure each wire to ground with both ends disconnected; a low reading means a harness short
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.

    Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.

  • John Deere ECU 000103.08Turbocharger speed not valid

    The controller sees an erratic, invalid or out-of-step signal from the turbocharger speed sensor, so it cannot rely on that input.· Erratic or implausible
    Check soon

    Causes

    • Intermittent connection at the turbocharger speed sensor plug or in its harness
    • Chafed wire that touches ground only when the machine moves
    • The turbocharger speed sensor wearing out or failing intermittently

    Checks

    1. 1Wiggle the turbocharger speed sensor harness and plug with the key on while watching the live value for jumps or dropouts
    2. 2Compare the live reading with the machine state (stopped, idling, working) to see when it goes wrong
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • John Deere ECU 000103.31Turbocharger speed missing

    The controller has set a condition code for the turbocharger speed sensor: the state it monitors exists, so it is telling the operator or the technician rather than reporting a broken part.· Other
    Check soon

    Causes

    • The real condition behind the turbocharger speed sensor is present
    • A related component or circuit that causes the condition
    • The message or reminder was not reset after the earlier service

    Checks

    1. 1Confirm on the machine that the condition behind the turbocharger speed sensor is real and act on it
    2. 2Read all other codes active at the same time, since this one is often a consequence of another fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 000108.02Barometric pressure sensor invalid

    The ECU reports that the barometric (ambient air pressure) sensor signal is invalid.· Other
    Check soon

    Causes

    • Barometric sensor or its wiring faulty, giving an invalid or stuck value
    • Connector at the sensor corroded or not fully seated
    • Sensor port blocked by dirt or water
    • ECU input fault when the sensor and wiring test good

    Checks

    1. 1Inspect the barometric sensor plug and wiring for corrosion, chafing and pushed-out terminals before anything else
    2. 2Measure the 5 V supply and ground at the sensor plug with the key on
    3. 3Compare the reading on the service tool with the real local air pressure; a big difference means a bad sensor or signal
    4. 4Clear the code, restart and see whether it returns at once with the wiring good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 000157.04Fuel rail pressure sensor voltage fault

    The ECU sees the fuel rail pressure sensor signal below its normal range.· Other
    Check soon

    Causes

    • Rail pressure sensor signal wire open or shorted to ground
    • No 5 V supply to the sensor
    • Sensor failed low

    Checks

    1. 1Check the 5 V supply and ground at the rail pressure sensor connector
    2. 2Check the signal wire for continuity and for a short to ground
    3. 3Inspect the sensor connector for corrosion and fuel
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 000157.10Fuel rail pressure drop

    The ECU sees fuel rail pressure drop below what is commanded.· Other
    Check soon

    Causes

    • Fuel filter blocked
    • Weak high pressure fuel pump
    • Injector leaking back or an external fuel leak

    Checks

    1. 1Replace the fuel filter if it is overdue and bleed the system following the engine manual
    2. 2Check the fuel supply pressure and the lines for air leaks
    3. 3Look for fuel leaks around the rail and injectors
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 000157.17Fuel rail pressure does not rise

    The fuel rail pressure sensor reading is below its normal range, so the controller reports a low value; this can be a real condition on the machine and not only a wiring fault.· Lost message
    Check soon

    Causes

    • A real low condition on the machine, such as low level, low pressure or a cold engine, behind the fuel rail pressure sensor
    • The fuel rail pressure sensor reading low because of a drifting sensor
    • Supply or feed problem that holds the value down

    Checks

    1. 1Confirm the real value with an independent gauge or by inspection before blaming the fuel rail pressure sensor
    2. 2Look for related codes and for a physical cause such as a low level, leak or weak supply
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • John Deere ECU 000611.03Injection circuit shorted

    The ECU sees a short in an injector circuit.· Other
    Check soon

    Causes

    • Injector solenoid coil shorted
    • Injector wire shorted to ground or to another wire
    • Damaged injector harness under the valve cover

    Checks

    1. 1Measure the injector coil resistance for each injector
    2. 2Check the injector harness for chafing under the valve cover
    3. 3Check the harness connectors for oil and water
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 000611.04Injection wiring burnt

    The controller detects a short circuit on the electronic injector circuit, so the circuit draws too much current or the signal is pulled to a fixed level.· Short circuit
    Check soon

    Causes

    • Wire to the electronic injector circuit chafed through and touching ground or a supply wire
    • Water or oil inside the electronic injector circuit connector bridging pins
    • Internal short inside the electronic injector circuit

    Checks

    1. 1Unplug the electronic injector circuit and see whether the code changes from a short to an open; if it does, the part is the likely culprit
    2. 2Measure each wire to ground with both ends disconnected; a low reading means a harness short
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.

    Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.

  • John Deere ECU 001347.07Fuel filter and rail attention

    The fuel rail pressure sensor does not respond as commanded or is stuck, which the controller detects from its feedback.· Other
    Check soon

    Causes

    • The fuel rail pressure sensor stuck from dirt, wear or damage
    • Actuator or driver weak or failing
    • Supply or wiring fault so the part is not driven properly

    Checks

    1. 1Move or command the fuel rail pressure sensor while watching the response; no movement points at the part, movement with a code points at the feedback
    2. 2Check the supply voltage and the ground at the fuel rail pressure sensor plug while it is commanded
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • John Deere ECU 002790.16Compressor outlet temperature high

    The turbocharger speed sensor reading is above its normal range, so the controller reports a high value; this can be a real condition on the machine and not only a wiring fault.· Lost message
    Check soon

    Causes

    • A real high condition on the machine, such as heat, load or restriction, behind the turbocharger speed sensor
    • The turbocharger speed sensor reading high because of a drifting sensor
    • Cooling, intake or supply problem that pushes the value up

    Checks

    1. 1Confirm the real value with an independent gauge or thermometer before blaming the turbocharger speed sensor
    2. 2Look for related codes and for a physical cause such as a blocked cooler or restriction
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

Shared checks

Checks, in order

  1. 1Read all active ECU codes first and note which sensor or circuit the code names
  2. 2Verify the real value with a mechanical gauge where one applies (oil pressure at the engine test port)
  3. 3Unplug the sensor and check the harness for 5 V reference and ground; compare the live value on the service screen with the engine stopped
  4. 4Inspect the air filter, intake hoses and exhaust for restriction and leaks before blaming a sensor
  5. 5For injector circuits check the injector harness and connector for chafing and oil

Causes

  • Real fault: low oil, worn pump, blocked air filter, leaking intake or restricted exhaust
  • Sensor failed or its plug corroded, giving a fixed or erratic signal
  • Wire shorted to supply or ground, or open, between the sensor and the ECU
  • EGR valve or turbo vane sticking from soot

Most common here: shorted high (3 of 24)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: The engine may derate, smoke, lack power or be protected by the ECU.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.