John Deere · Main controller (MCZ) - pressure sensors
John Deere Fault Code MCZ 11202.04
Pump 2 delivery pressure sensor (B37) signal low
What does John Deere code MCZ 11202.04 mean?
The main controller reads the pump 2 delivery pressure sensor (B37) on the pump 2 delivery line as low. Urgency: check soon - the machine may derate or limit a function. Check first: measure 5 V and ground at the B37 connector with the key on; if the supply is missing, trace it back to the MCZ.
- MCZ
- Which controller reports it
- 11202
- What is at fault
- .04
- How it failed
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Measure 5 V and ground at the B37 connector with the key on; if the supply is missing, trace it back to the MCZ
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- Signal wire cut or worn through where it crosses a bracket near pump 2
- B37 signal wire touching the frame and shorted to ground
- B37 connector supply pin loose or corroded, so the sensor is unpowered
- B37 failed low inside
How it failed
You'll notice: Pump 2 delivery pressure reads zero, so the MCZ cannot tell when pump 2 is loaded and its power balance with pump 1 goes wrong.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Pump pressure and hydraulic oil temperature sensors
- MCZ 11200.04Pump 1 delivery pressure sensor (B35) signal lowOtherCheck soon
- MCZ 11201.03Fan pump delivery pressure sensor circuit highOtherCheck soon
- MCZ 11201.04Fan pump delivery pressure sensor circuit lowOtherCheck soon
- MCZ 11202.03Pump 2 delivery pressure sensor (B37) signal highOtherCheck soon
- MCZ 11202.04Pump 2 delivery pressure sensor (B37) signal lowOtherCheck soon
- MCZ 11206.03Pump 1 control pressure sensor (B36) signal highOtherCheck soon
- MCZ 11206.04Pump 1 control pressure sensor (B36) signal lowOtherCheck soon
- MCZ 11208.03Pump 2 control pressure sensor circuit highOtherCheck soon
- MCZ 11208.04Pump 2 control pressure sensor circuit lowOtherCheck soon
Show the other 9 codesHide the other codes
- MCZ 11200.03Pump 1 delivery pressure sensor (B35) signal highOtherCheck soon
- MCZ 11901.03Hydraulic oil temperature sensor (B40) highOtherCheck soon
- MCZ 11901.04Hydraulic oil temperature sensor (B40) lowOtherCheck soon
- MCZ 11992.03Pump 2 control pressure sensor circuit voltage highShorted highCheck soon
- MCZ 11992.04Pump 2 control pressure sensor circuit voltage lowShorted lowCheck soon
- MCZ 11994.03Pump 1 control pressure sensor circuit voltage highShorted highCheck soon
- MCZ 11994.04Pump 1 control pressure sensor circuit voltage lowShorted lowCheck soon
- MCZ 15011.03Secondary hydraulic oil temperature sensor (B68) highOpen circuitCheck soon
- MCZ 15011.04Secondary hydraulic oil temperature sensor (B68) lowShorted lowCheck soon
Other John Deere codes: Main controller (MCZ) - pressure sensors
Related on Equipments Finder
Source
Excavator Fault Codes - John Deere excavators fault codes list (MCZ/ECU/DSZ)
This source lists MCZ 11202.04 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere G-series excavators (210G/210GLC and 350G class) with MCZ main controller; confirm against serial number.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
