John Deere · Engine control unit (ECU) - Electrical
John Deere Fault Code ECU 000158.01
Battery voltage low
What does John Deere code ECU 000158.01 mean?
The ECU sees its supply voltage drop below the lower limit. Low supply can set other communication codes, cause the engine to stall or restart poorly, and the operator may see a battery warning. Urgency: check soon - the machine may derate or limit a function. Check first: measure battery voltage with the engine off and again with the engine running.
- ECU
- Which controller reports it
- .01
- Data below normal, most severe
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Measure battery voltage with the engine off and again with the engine running
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- Weak or discharged batteries
- Loose or corroded battery terminals or earth straps
- Alternator not charging
- High resistance in the ECU supply wire or fuse holder
How it failed
You'll notice: The ECU supply voltage has dropped below its limit.
Shorted lowRead from how the source describes the code
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Battery, alternator and tractor basic control unit (BCU)
5 other codes on this part are also shorted low (ECU 000158.17, BCU 000168.17, BCU 000168.18, ECU 000627.01 and more). When they show together, start at the wiring and connector they share.
- BCU 000070.31Handbrake faultOtherCheck soon
- ECU 000158.01Battery voltage lowShorted lowCheck soon
- ECU 000158.17Battery voltage low (power removed from ECU)Shorted lowCheck soon
- BCU 000168.16System voltage too high with engine runningShorted highCheck soon
- BCU 000168.17System voltage too low at about 1,500 rpmShorted lowCheck soon
- BCU 000168.18System voltage too low above 1,500 rpmShorted lowCheck soon
- ECU 000627.01Electronic injection voltage lowShorted lowCheck soon
- ECU 000627.18Battery voltage below normalShorted lowCheck soon
- BCU 000629.12Control unit internal faultLost messageStop now
Show the other 13 codesHide the other codes
- BCU 000639.12Control unit interior system errorOtherStop now
- BCU 000639.1329-bit CAN bus high error rateLost messageCheck soon
- BCU 000639.1429-bit CAN bus higher error rateLost messageCheck soon
- BCU 000746.31Differential lock solenoid valve circuit faultOtherCheck soon
- BCU 001676.31LTC coolant pump relay circuit faultOtherCheck soon
- DSZ 13304.02Alternator alarm (output above 33.5 V)Lost messageStop now
- ICZ 13304.02Alternator alarm (output above 33.5 V)Lost messageStop now
- ICZ 20103.02Alternator alarmOtherCheck soon
- BCU 299780.07Turn-signal switch faultOtherCheck soon
- BCU 302001.31Service interval reminder: 250 hoursOtherInformation
- BCU 302002.31Service interval reminder: 500 hoursOtherInformation
- BCU 302003.31Service interval reminder: 750 hoursOtherInformation
- BCU 302004.31Service interval reminder: 1,500 hoursOtherInformation
Related on Equipments Finder
Source
Excavator Fault Codes - John Deere excavators fault codes list (MCZ/ECU/DSZ)
This source lists ECU 000158.01 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere G-series excavators (210G/210GLC and 350G class) with MCZ main controller; confirm against serial number.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
