EF Logo

Develon (Doosan) fault codes

Develon (formerly Doosan) excavators and wheel loaders show fault codes on the gauge panel for the machine controller and the engine.

363 codes in 24 families32 stop now, 331 check soon, 0 info

363 Develon codes - type a code, or a word from the problem.

Covers Excavators, Wheel loaders.

Where to look

  1. 01Switch the key on and open the monitor fault or service menu on the gauge panel to…
  2. 02Note the full code exactly as written, including the number of digits, and your…
  3. 03Match the code to the family table in this section and check the part named, starting…
  4. 04Clear the code after the repair and run the machine to see if it returns.
  5. 05Use the dealer diagnostic software when the monitor shows more than one fault or a…
How to read Develon fault codes, in full
  1. Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.
  2. Note the full code exactly as written, including the number of digits, and your model, because V and E codes change between models.
  3. Match the code to the family table in this section and check the part named, starting with its connector and harness.
  4. Clear the code after the repair and run the machine to see if it returns; newer machines may add a two-digit suffix after a dash for the failure type.
  5. Use the dealer diagnostic software (DMS) when the monitor shows more than one fault or a code you cannot match.

How urgent is a Develon code?

Stop now32 codes
Shut down and fix before working on. Running on risks damage or the machine locks out.
Check soon331 codes
The machine may derate or limit a function. Find the cause before the next shift.
Information0 codes
A reminder or status message. Nothing is failing yet.

Pick your system

Find the part of the machine, then the family your code belongs to.

Code range
The first and last code in the family, as the machine shows them.
Codes
How many codes the family holds; each is explained on its page.
Severity mix
The share of stop, check and info codes. The dot after it is the most urgent one in the family.

Hydraulic valve drivers56 codes

Relays6 codes

Pressure sensors16 codes

Sensors and inputs28 codes

Engine sensors48 codes

Communication18 codes

Engine controller37 codes

Fuel system59 codes

Air and exhaust20 codes

Aftertreatment45 codes

Engine protection20 codes

Transmission10 codes

Most searched Develon codes

Quick answers

How do I read Develon fault codes?

Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes. Note the full code exactly as written, including the number of digits, and your model, because V and E codes change between models.

Which Develon codes mean stop now?

32 of the 363 Develon codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example E000015, E000093, E000129, E000157. 331 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.

What should I check first on a Develon code?

Most Develon codes here (27 of 363) read as real condition: the sensor reading is valid but outside the allowed range - the problem may be real. First test, as general workshop practice: check the real value with a separate gauge or thermometer before blaming the sensor.

Which Develon codes are looked up most?

V000201 (gauge panel error), V201 (gauge panel communication error (v201)), V210 (pump p/v fault (v210)), V211 (cooling fan proportional valve fault (v211)). Each page gives the meaning, the likely causes and the checks.

Sources

Every code was read from these documents and written in our own words.

Other makers

Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.