EF Logo

Develon · Transmission

Develon Wheel loader transmission T codes fault codes

Transmission controller entries: logical errors from the shift levers, gear range and direction signals, and open or shorted circuits on the clutch cut-off and sump temperature sensor. The source copy of the table is cut off after T026, so later T codes are not listed.

FaultCheckT010Develon · Wheel loader transmission T codes
Code shows hereFAULTT010

Where this code shows

Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.

What do these codes mean?

Develon codes T010 to T026 are all about the wheel loader transmission T codes. The most common failure type is shorted high (4 of 10); none needs an immediate stop. Start with this check: check the shift lever and its connector and note what you find before replacing any part.

How urgent are they?

None of the 10 codes here means stop now; all 10 can wait until the shift ends, but find the cause before the next one.

  • Check soon10

What should I check first?

Check the shift lever and its connector and note what you find before replacing any part.

Shared checks

10 of 10

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Develon T010Logical error at direction select signal, 3rd shift lever

    Same failure as T012 on the logical error at direction select signal, 3rd shift lever, a different part of the same kind as the logical error at gear range signal.· Other
    Check soon

    Causes

    • Fault in the logical error at direction select signal, 3rd shift lever or its wiring
    • Any cause listed under T012

    Checks

    1. 1Check the logical error at direction select signal, 3rd shift lever connector and wiring first, then follow the checks listed under T012.
    2. 2Clear the code and confirm whether T010 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon T012Logical error at gear range signal

    The transmission controller sees contradictory gear range inputs, for example two ranges at once or none.· Other
    Check soon

    Causes

    • Faulty range switch or lever
    • Wiring short or open
    • Connector corrosion

    Checks

    1. 1Check the live range inputs against the lever position.
    2. 2Measure the switch circuit for each position.
    3. 3Inspect the lever connector.
    4. 4Look for a wire shared by two circuits that may be shorted.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon T013Logical error at direction select signal

    Same failure as T012 on the logical error at direction select signal, a different part of the same kind as the logical error at gear range signal.· Other
    Check soon

    Causes

    • Fault in the logical error at direction select signal or its wiring
    • Any cause listed under T012

    Checks

    1. 1Check the logical error at direction select signal connector and wiring first, then follow the checks listed under T012.
    2. 2Clear the code and confirm whether T013 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon T014Logical error at engine derating device

    Same failure as T012 on the logical error at engine derating device, a different part of the same kind as the logical error at gear range signal.· Other
    Check soon

    Causes

    • Fault in the logical error at engine derating device or its wiring
    • Any cause listed under T012

    Checks

    1. 1Check the logical error at engine derating device connector and wiring first, then follow the checks listed under T012.
    2. 2Clear the code and confirm whether T014 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon T015Logical error at parkbrake status

    Same failure as T012 on the logical error at parkbrake status, a different part of the same kind as the logical error at gear range signal.· Other
    Check soon

    Causes

    • Fault in the logical error at parkbrake status or its wiring
    • Any cause listed under T012

    Checks

    1. 1Check the logical error at parkbrake status connector and wiring first, then follow the checks listed under T012.
    2. 2Clear the code and confirm whether T015 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon T016Logical error at direction select signal, 2nd shift lever

    Same failure as T012 on the logical error at direction select signal, 2nd shift lever, a different part of the same kind as the logical error at gear range signal.· Other
    Check soon

    Causes

    • Fault in the logical error at direction select signal, 2nd shift lever or its wiring
    • Any cause listed under T012

    Checks

    1. 1Check the logical error at direction select signal, 2nd shift lever connector and wiring first, then follow the checks listed under T012.
    2. 2Clear the code and confirm whether T016 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon T021Short circuit to battery voltage at clutch cut-off / inch pedal input

    The clutch cut-off or inching pedal input of the transmission controller is shorted to battery voltage.· Shorted high
    Check soon

    Causes

    • Short to battery in the pedal wire
    • Faulty pedal switch or sensor
    • Connector damage

    Checks

    1. 1Measure the pedal input with the key on and compare with the pedal position.
    2. 2Check the wire for a short to a power circuit.
    3. 3Inspect the pedal connector and mounting.
    4. 4Compare live pedal data in the tool.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Develon T022Short circuit to ground or open circuit at clutch cut-off / inch pedal input

    Same failure as T021 on the short circuit to ground or open circuit at clutch cut-off / inch pedal input, a different part of the same kind as the short circuit to battery voltage at clutch cut-off / inch pedal input.· Shorted high
    Check soon

    Causes

    • Fault in the short circuit to ground or open circuit at clutch cut-off / inch pedal input or its wiring
    • Any cause listed under T021

    Checks

    1. 1Check the short circuit to ground or open circuit at clutch cut-off / inch pedal input connector and wiring first, then follow the checks listed under T021.
    2. 2Clear the code and confirm whether T022 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Develon T025Short circuit to battery voltage or open circuit at transmission sump temperature sensor input

    Same failure as T021 on the short circuit to battery voltage or open circuit at transmission sump temperature sensor input, a different part of the same kind as the short circuit to battery voltage at clutch cut-off / inch pedal input.· Shorted high
    Check soon

    Causes

    • Fault in the short circuit to battery voltage or open circuit at transmission sump temperature sensor input or its wiring
    • Any cause listed under T021

    Checks

    1. 1Check the short circuit to battery voltage or open circuit at transmission sump temperature sensor input connector and wiring first, then follow the checks listed under T021.
    2. 2Clear the code and confirm whether T025 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Develon T026Short circuit to ground at transmission sump temperature sensor input

    Same failure as T021 on the short circuit to ground at transmission sump temperature sensor input, a different part of the same kind as the short circuit to battery voltage at clutch cut-off / inch pedal input.· Shorted high
    Check soon

    Causes

    • Fault in the short circuit to ground at transmission sump temperature sensor input or its wiring
    • Any cause listed under T021

    Checks

    1. 1Check the short circuit to ground at transmission sump temperature sensor input connector and wiring first, then follow the checks listed under T021.
    2. 2Clear the code and confirm whether T026 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

Shared checks

Checks, in order

  1. 1Check the shift lever and its connector and note what you find before replacing any part.
  2. 2Measure the sensor and its wires and note what you find before replacing any part.
  3. 3Check for contradictory signals in the live data.
  4. 4Inspect harness near the transmission and note what you find before replacing any part.

Causes

  • Faulty shift lever or switch
  • Wiring short or open
  • Faulty sensor
  • Controller fault

Most common here: shorted high (4 of 10)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: The loader may not shift or select direction, or the clutch cut-off may act wrongly.

Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.