EF Logo

Develon · Engine sensors

Develon Engine pressure, temperature, pedal and speed sensors fault codes

Sensors the engine controller reads for oil pressure, boost, coolant, intake and fuel temperatures, throttle and pedal position and crank and cam speed. A bad reading is replaced by a default value, so the engine may run with less power or start hard.

FaultCheckE000051Develon · Engine pressure, temperature, pedal and speed sensors
Code shows hereFAULTE000051

Where this code shows

Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.

What do these codes mean?

Develon codes E000051 to E520612 are all about the engine pressure, temperature, pedal and speed sensors. The most common failure type is lost message (2 of 24); none needs an immediate stop. Start with this check: read the live value for the named sensor with the tool and compare with the condition on the machine.

How urgent are they?

None of the 24 codes here means stop now; all 24 can wait until the shift ends, but find the cause before the next one.

  • Check soon24

What should I check first?

Read the live value for the named sensor with the tool and compare with the condition on the machine.

Shared checks

24 of 24

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Develon E000051Throttle valve position sensor

    Same failure as E000091 on the throttle valve position sensor, a different part of the same kind as the accelerator pedal position.· Other
    Check soon

    Causes

    • Fault in the throttle valve position sensor or its wiring
    • Any cause listed under E000091

    Checks

    1. 1Check the throttle valve position sensor connector and wiring first, then follow the checks listed under E000091.
    2. 2Clear the code and confirm whether E000051 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000091Accelerator Pedal Position

    The accelerator pedal position signal tells the engine controller how much speed the operator asks for.· Other
    Check soon

    Causes

    • Worn pedal or sensor track
    • Open or shorted signal wire
    • Lost sensor supply or ground
    • Connector corrosion

    Checks

    1. 1Press the pedal slowly and watch the live position for a smooth change.
    2. 2Check the 5 V supply and ground at the pedal connector.
    3. 3Inspect the pedal harness and connector for wear.
    4. 4Compare both signal channels, if present, to see that they agree.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000100Oil pressure sensor

    The oil pressure sensor reports engine oil pressure to the engine controller.· Other
    Check soon

    Causes

    • Failed oil pressure sensor
    • Lost 5 V supply or ground
    • Open or shorted signal wire
    • Real low oil pressure from low oil or a worn pump

    Checks

    1. 1Check the oil level and condition before anything else.
    2. 2Check the 5 V supply and ground at the sensor connector with the key on.
    3. 3Read the live value with the engine off and then running; the signal should move within the 0.5-4.5 V range.
    4. 4Fit a mechanical gauge to confirm real pressure if the reading is low.
    5. 5Inspect the connector for oil and corrosion.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000102Boost pressure sensor

    Same failure as E000100 on the boost pressure sensor, a different part of the same kind as the oil pressure sensor.· Other
    Check soon

    Causes

    • Fault in the boost pressure sensor or its wiring
    • Any cause listed under E000100

    Checks

    1. 1Check the boost pressure sensor connector and wiring first, then follow the checks listed under E000100.
    2. 2Clear the code and confirm whether E000102 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000105Air Intake Manifold temperature

    Same failure as E000110 on the air intake manifold temperature, a different part of the same kind as the coolant temperature.· Other
    Check soon

    Causes

    • Fault in the air intake manifold temperature or its wiring
    • Any cause listed under E000110

    Checks

    1. 1Check the air intake manifold temperature connector and wiring first, then follow the checks listed under E000110.
    2. 2Clear the code and confirm whether E000105 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000108Barometric pressure sensor in ECU

    Same failure as E000100 on the barometric pressure sensor in ecu, a different part of the same kind as the oil pressure sensor.· Other
    Check soon

    Causes

    • Fault in the barometric pressure sensor in ecu or its wiring
    • Any cause listed under E000100

    Checks

    1. 1Check the barometric pressure sensor in ecu connector and wiring first, then follow the checks listed under E000100.
    2. 2Clear the code and confirm whether E000108 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000110Coolant temperature

    The coolant temperature sensor tells the engine controller how hot the coolant is.· Lost message
    Check soon

    Causes

    • Failed temperature sensor
    • Open or shorted signal wire
    • Corroded connector
    • Real overheating or a stuck thermostat

    Checks

    1. 1Measure the sensor resistance with the connector unplugged and compare with the manual curve.
    2. 2Compare the live value with an infrared reading on the thermostat housing.
    3. 3Check the harness for chafe near the cylinder head.
    4. 4Check coolant level and the thermostat if the value is really high.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon E000132Air Mass Flow sensor

    Same failure as E000100 on the air mass flow sensor, a different part of the same kind as the oil pressure sensor.· Other
    Check soon

    Causes

    • Fault in the air mass flow sensor or its wiring
    • Any cause listed under E000100

    Checks

    1. 1Check the air mass flow sensor connector and wiring first, then follow the checks listed under E000100.
    2. 2Clear the code and confirm whether E000132 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000172Air Mass Flow sensor temperature

    Same failure as E000110 on the air mass flow sensor temperature, a different part of the same kind as the coolant temperature.· Other
    Check soon

    Causes

    • Fault in the air mass flow sensor temperature or its wiring
    • Any cause listed under E000110

    Checks

    1. 1Check the air mass flow sensor temperature connector and wiring first, then follow the checks listed under E000110.
    2. 2Clear the code and confirm whether E000172 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000174Fuel temperature sensor

    Same failure as E000110 on the fuel temperature sensor, a different part of the same kind as the coolant temperature.· Other
    Check soon

    Causes

    • Fault in the fuel temperature sensor or its wiring
    • Any cause listed under E000110

    Checks

    1. 1Check the fuel temperature sensor connector and wiring first, then follow the checks listed under E000110.
    2. 2Clear the code and confirm whether E000174 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000175Oil temperature sensor

    Same failure as E000110 on the oil temperature sensor, a different part of the same kind as the coolant temperature.· Other
    Check soon

    Causes

    • Fault in the oil temperature sensor or its wiring
    • Any cause listed under E000110

    Checks

    1. 1Check the oil temperature sensor connector and wiring first, then follow the checks listed under E000110.
    2. 2Clear the code and confirm whether E000175 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000190E/G SPEED SENSOR

    Same failure as E000091 on the e/g speed sensor, a different part of the same kind as the accelerator pedal position.· Other
    Check soon

    Causes

    • Fault in the e/g speed sensor or its wiring
    • Any cause listed under E000091

    Checks

    1. 1Check the e/g speed sensor connector and wiring first, then follow the checks listed under E000091.
    2. 2Clear the code and confirm whether E000190 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000611Intermediate speed switch validation

    Same failure as E000091 on the intermediate speed switch validation, a different part of the same kind as the accelerator pedal position.· Other
    Check soon

    Causes

    • Fault in the intermediate speed switch validation or its wiring
    • Any cause listed under E000091

    Checks

    1. 1Check the intermediate speed switch validation connector and wiring first, then follow the checks listed under E000091.
    2. 2Clear the code and confirm whether E000611 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000612E/G magnetic pickup. speed/position lost both signals

    Same failure as E000091 on the e/g magnetic pickup. speed/position lost both signals, a different part of the same kind as the accelerator pedal position.· Other
    Check soon

    Causes

    • Fault in the e/g magnetic pickup. speed/position lost both signals or its wiring
    • Any cause listed under E000091

    Checks

    1. 1Check the e/g magnetic pickup. speed/position lost both signals connector and wiring first, then follow the checks listed under E000091.
    2. 2Clear the code and confirm whether E000612 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000636G Sensor Fault

    Same failure as E000091 on the g sensor fault, a different part of the same kind as the accelerator pedal position.· Other
    Check soon

    Causes

    • Fault in the g sensor fault or its wiring
    • Any cause listed under E000091

    Checks

    1. 1Check the g sensor fault connector and wiring first, then follow the checks listed under E000091.
    2. 2Clear the code and confirm whether E000636 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000723Engine speed sensor error

    Same failure as E000091 on the engine speed sensor error, a different part of the same kind as the accelerator pedal position.· Other
    Check soon

    Causes

    • Fault in the engine speed sensor error or its wiring
    • Any cause listed under E000091

    Checks

    1. 1Check the engine speed sensor error connector and wiring first, then follow the checks listed under E000091.
    2. 2Clear the code and confirm whether E000723 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E000968Idle Speed Up-Down Switch Fault

    Same failure as E000091 on the idle speed up-down switch fault, a different part of the same kind as the accelerator pedal position.· Other
    Check soon

    Causes

    • Fault in the idle speed up-down switch fault or its wiring
    • Any cause listed under E000091

    Checks

    1. 1Check the idle speed up-down switch fault connector and wiring first, then follow the checks listed under E000091.
    2. 2Clear the code and confirm whether E000968 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E001131Manifold Temperature Sensor Fault

    Same failure as E000110 on the manifold temperature sensor fault, a different part of the same kind as the coolant temperature.· Other
    Check soon

    Causes

    • Fault in the manifold temperature sensor fault or its wiring
    • Any cause listed under E000110

    Checks

    1. 1Check the manifold temperature sensor fault connector and wiring first, then follow the checks listed under E000110.
    2. 2Clear the code and confirm whether E001131 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E001136Sensor circuit-voltage

    Same failure as E000091 on the sensor circuit-voltage, a different part of the same kind as the accelerator pedal position.· Other
    Check soon

    Causes

    • Fault in the sensor circuit-voltage or its wiring
    • Any cause listed under E000091

    Checks

    1. 1Check the sensor circuit-voltage connector and wiring first, then follow the checks listed under E000091.
    2. 2Clear the code and confirm whether E001136 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E003464Throttle valve control

    Same failure as E000091 on the throttle valve control, a different part of the same kind as the accelerator pedal position.· Other
    Check soon

    Causes

    • Fault in the throttle valve control or its wiring
    • Any cause listed under E000091

    Checks

    1. 1Check the throttle valve control connector and wiring first, then follow the checks listed under E000091.
    2. 2Clear the code and confirm whether E003464 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520199Crankshaft sensor

    Same failure as E000091 on the crankshaft sensor, a different part of the same kind as the accelerator pedal position.· Other
    Check soon

    Causes

    • Fault in the crankshaft sensor or its wiring
    • Any cause listed under E000091

    Checks

    1. 1Check the crankshaft sensor connector and wiring first, then follow the checks listed under E000091.
    2. 2Clear the code and confirm whether E520199 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520200Camshaft sensor

    Same failure as E000091 on the camshaft sensor, a different part of the same kind as the accelerator pedal position.· Other
    Check soon

    Causes

    • Fault in the camshaft sensor or its wiring
    • Any cause listed under E000091

    Checks

    1. 1Check the camshaft sensor connector and wiring first, then follow the checks listed under E000091.
    2. 2Clear the code and confirm whether E520200 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon E520336Engine temperature sensor plausibility

    Same failure as E000110 on the engine temperature sensor plausibility, a different part of the same kind as the coolant temperature.· Erratic or implausible
    Check soon

    Causes

    • Fault in the engine temperature sensor plausibility or its wiring
    • Any cause listed under E000110

    Checks

    1. 1Check the engine temperature sensor plausibility connector and wiring first, then follow the checks listed under E000110.
    2. 2Clear the code and confirm whether E520336 returns on its own.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Develon E520612Accel pedal CAN Max error

    Same failure as E000091 on the accel pedal can max error, a different part of the same kind as the accelerator pedal position.· Lost message
    Check soon

    Causes

    • Fault in the accel pedal can max error or its wiring
    • Any cause listed under E000091

    Checks

    1. 1Check the accel pedal can max error connector and wiring first, then follow the checks listed under E000091.
    2. 2Clear the code and confirm whether E520612 returns on its own.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

Shared checks

Checks, in order

  1. 1Read the live value for the named sensor with the tool and compare with the condition on the machine.
  2. 2Check 5 V reference and ground at the sensor connector with the key on.
  3. 3Inspect the connector for water, green corrosion and pushed-back pins.
  4. 4Wiggle the harness while watching the value for dropouts.

Causes

  • Failed sensor or connector
  • Wiring open, short or chafed
  • Lost sensor supply or ground
  • Real condition out of range (low oil, hot coolant)

Most common here: lost message (2 of 24)

Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

When to stop

You'll notice: A warning lamp lights and the engine may derate or idle roughly; the code is stored in the engine controller and shown on the monitor.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.