EF Logo

Develon · Sensors and inputs

Develon Wheel loader sensors, joysticks and pedals fault codes

Pressure and angle sensors, joystick and pedal inputs, alternator potential and fuel-water detection on the H-series wheel loader table.

FaultCheckV023Develon · Wheel loader sensors, joysticks and pedals
Code shows hereFAULTV023

Where this code shows

Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.

What do these codes mean?

Develon codes V023 to V038 are all about the wheel loader sensors, joysticks and pedals. None needs an immediate stop. Start with this check: match the code name to the part and check its connector.

How urgent are they?

None of the 16 codes here means stop now; all 16 can wait until the shift ends, but find the cause before the next one.

  • Check soon16

What should I check first?

Match the code name to the part and check its connector.

Shared checks

16 of 16

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Develon V023Main Pump Pressure Sensor

    The main pump pressure sensor on the wheel loader reports hydraulic pressure to the controller.· Other
    Check soon

    Causes

    • Failed pressure sensor
    • Lost 5 V supply or ground
    • Open or shorted signal wire
    • Water in the connector

    Checks

    1. 1Check 5 V supply and ground at the sensor with the key on.
    2. 2Read the signal at rest and under load within the 0.5-4.5 V range.
    3. 3Inspect the connector for moisture.
    4. 4Compare with a test gauge if fitted.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V024Steering Pump Pressure Sensor

    Same failure as V023 on the steering pump pressure sensor, a different part of the same kind as the main pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the steering pump pressure sensor or its wiring
    • Any cause listed under V023

    Checks

    1. 1Check the steering pump pressure sensor connector and wiring first, then follow the checks listed under V023.
    2. 2Clear the code and confirm whether V024 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V025Boom Angle Sensor

    Same failure as V023 on the boom angle sensor, a different part of the same kind as the main pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the boom angle sensor or its wiring
    • Any cause listed under V023

    Checks

    1. 1Check the boom angle sensor connector and wiring first, then follow the checks listed under V023.
    2. 2Clear the code and confirm whether V025 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V026Bucket Angle Sensor

    Same failure as V023 on the bucket angle sensor, a different part of the same kind as the main pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the bucket angle sensor or its wiring
    • Any cause listed under V023

    Checks

    1. 1Check the bucket angle sensor connector and wiring first, then follow the checks listed under V023.
    2. 2Clear the code and confirm whether V026 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V027Electronic MCV Boom Joystick

    The electronic joystick input (boom joystick) tells the controller how far the lever is moved.· Other
    Check soon

    Causes

    • Worn joystick sensor
    • Open or shorted signal wire
    • Lost supply or ground
    • Connector corrosion

    Checks

    1. 1Move the lever slowly through its range and watch the monitor value for steps or dropouts.
    2. 2Check supply and ground at the joystick connector.
    3. 3Inspect the harness at the cab base.
    4. 4Compare with the other joystick if the type matches.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V028Electronic MCV Bucket Joystick

    Same failure as V027 on the electronic mcv bucket joystick, a different part of the same kind as the electronic mcv boom joystick.· Other
    Check soon

    Causes

    • Fault in the electronic mcv bucket joystick or its wiring
    • Any cause listed under V027

    Checks

    1. 1Check the electronic mcv bucket joystick connector and wiring first, then follow the checks listed under V027.
    2. 2Clear the code and confirm whether V028 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V029Electronic MCV Option Joystick

    Same failure as V027 on the electronic mcv option joystick, a different part of the same kind as the electronic mcv boom joystick.· Other
    Check soon

    Causes

    • Fault in the electronic mcv option joystick or its wiring
    • Any cause listed under V027

    Checks

    1. 1Check the electronic mcv option joystick connector and wiring first, then follow the checks listed under V027.
    2. 2Clear the code and confirm whether V029 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V030Electric Steering Joystick

    Same failure as V027 on the electric steering joystick, a different part of the same kind as the electronic mcv boom joystick.· Other
    Check soon

    Causes

    • Fault in the electric steering joystick or its wiring
    • Any cause listed under V027

    Checks

    1. 1Check the electric steering joystick connector and wiring first, then follow the checks listed under V027.
    2. 2Clear the code and confirm whether V030 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V031Alternator Potential

    Same failure as V023 on the alternator potential, a different part of the same kind as the main pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the alternator potential or its wiring
    • Any cause listed under V023

    Checks

    1. 1Check the alternator potential connector and wiring first, then follow the checks listed under V023.
    2. 2Clear the code and confirm whether V031 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V032Boom Magnet

    Same failure as V023 on the boom magnet, a different part of the same kind as the main pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the boom magnet or its wiring
    • Any cause listed under V023

    Checks

    1. 1Check the boom magnet connector and wiring first, then follow the checks listed under V023.
    2. 2Clear the code and confirm whether V032 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V033Reserved Magnet

    Same failure as V023 on the reserved magnet, a different part of the same kind as the main pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the reserved magnet or its wiring
    • Any cause listed under V023

    Checks

    1. 1Check the reserved magnet connector and wiring first, then follow the checks listed under V023.
    2. 2Clear the code and confirm whether V033 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V034Return to Dig Magnet

    Same failure as V023 on the return to dig magnet, a different part of the same kind as the main pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the return to dig magnet or its wiring
    • Any cause listed under V023

    Checks

    1. 1Check the return to dig magnet connector and wiring first, then follow the checks listed under V023.
    2. 2Clear the code and confirm whether V034 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V035Water In Fuel Sensor

    Same failure as V023 on the water in fuel sensor, a different part of the same kind as the main pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the water in fuel sensor or its wiring
    • Any cause listed under V023

    Checks

    1. 1Check the water in fuel sensor connector and wiring first, then follow the checks listed under V023.
    2. 2Clear the code and confirm whether V035 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V036Brake Oil Pressure Sensor

    Same failure as V023 on the brake oil pressure sensor, a different part of the same kind as the main pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the brake oil pressure sensor or its wiring
    • Any cause listed under V023

    Checks

    1. 1Check the brake oil pressure sensor connector and wiring first, then follow the checks listed under V023.
    2. 2Clear the code and confirm whether V036 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V037Accel Pedal

    Same failure as V027 on the accel pedal, a different part of the same kind as the electronic mcv boom joystick.· Other
    Check soon

    Causes

    • Fault in the accel pedal or its wiring
    • Any cause listed under V027

    Checks

    1. 1Check the accel pedal connector and wiring first, then follow the checks listed under V027.
    2. 2Clear the code and confirm whether V037 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V038Power Mode Foot Switch

    Same failure as V027 on the power mode foot switch, a different part of the same kind as the electronic mcv boom joystick.· Other
    Check soon

    Causes

    • Fault in the power mode foot switch or its wiring
    • Any cause listed under V027

    Checks

    1. 1Check the power mode foot switch connector and wiring first, then follow the checks listed under V027.
    2. 2Clear the code and confirm whether V038 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Match the code name to the part and check its connector.
  2. 2Measure supply and signal with the key on and note what you find before replacing any part.
  3. 3Compare the monitor reading with the real position or pressure.
  4. 4Inspect the harness at the cab and articulation joint for chafe.

Causes

  • Failed sensor or joystick
  • Open or chafed wiring
  • Connector moisture
  • Supply or ground fault

When to stop

You'll notice: A joystick or pedal movement is not recognised, a gauge is wrong or a protection is disabled, with the V code on the monitor.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.