Develon · Fuel system
Develon Injector drivers and misfire monitoring fault codes
Injector solenoid power stages, injector circuits and misfire counters for each cylinder, plus charge-circuit and injection monitoring. Cylinder numbers follow the table.
Where this code shows
Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.
What do these codes mean?
Develon codes E000651 to E520626 are all about the injector drivers and misfire monitoring. The most common failure type is open circuit (6 of 26); none needs an immediate stop. Start with this check: note the cylinder number in the code and compare its misfire count with the others.
How urgent are they?
None of the 26 codes here means stop now; all 26 can wait until the shift ends, but find the cause before the next one.
- Check soon26
What should I check first?
Note the cylinder number in the code and compare its misfire count with the others.
Shared checks26 of 26
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Develon E000651Injector solenoid driver cylinder 1 circuit
Same failure as E000734 on the injector solenoid driver cylinder 1 circuit, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Injector solenoid driver cylinder 1 circuit'. The Isuzu engine table words this code as "Injection Nozzle #1Drive System Open Circuit Fault", so confirm against the table for your engine.· Open circuitOpen circuitCheck soonCauses
- Fault in the injector solenoid driver cylinder 1 circuit or its wiring
- Any cause listed under E000734
Checks
- 1Check the injector solenoid driver cylinder 1 circuit connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E000651 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Develon E000652Injector solenoid driver cylinder 2 circuit
Same failure as E000734 on the injector solenoid driver cylinder 2 circuit, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Injector solenoid driver cylinder 2 circuit'. The Isuzu engine table words this code as "Injection Nozzle #2Drive System Open Circuit Fault", so confirm against the table for your engine.· Open circuitOpen circuitCheck soonCauses
- Fault in the injector solenoid driver cylinder 2 circuit or its wiring
- Any cause listed under E000734
Checks
- 1Check the injector solenoid driver cylinder 2 circuit connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E000652 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Develon E000653Injector solenoid driver cylinder 3 circuit
Same failure as E000734 on the injector solenoid driver cylinder 3 circuit, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Injector solenoid driver cylinder 3 circuit'. The Isuzu engine table words this code as "Injection Nozzle #3Drive System Open Circuit Fault", so confirm against the table for your engine.· Open circuitOpen circuitCheck soonCauses
- Fault in the injector solenoid driver cylinder 3 circuit or its wiring
- Any cause listed under E000734
Checks
- 1Check the injector solenoid driver cylinder 3 circuit connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E000653 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Develon E000654Injector solenoid driver cylinder 4 circuit
Same failure as E000734 on the injector solenoid driver cylinder 4 circuit, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Injector solenoid driver cylinder 4 circuit'. The Isuzu engine table words this code as "Injection Nozzle #4Drive System Open Circuit Fault", so confirm against the table for your engine.· Open circuitOpen circuitCheck soonCauses
- Fault in the injector solenoid driver cylinder 4 circuit or its wiring
- Any cause listed under E000734
Checks
- 1Check the injector solenoid driver cylinder 4 circuit connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E000654 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Develon E000655Injector solenoid driver cylinder 5 circuit
Same failure as E000734 on the injector solenoid driver cylinder 5 circuit, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Injector solenoid driver cylinder 5 circuit'. The Isuzu engine table words this code as "Injection Nozzle #5Drive System Open Circuit Fault", so confirm against the table for your engine.· Open circuitOpen circuitCheck soonCauses
- Fault in the injector solenoid driver cylinder 5 circuit or its wiring
- Any cause listed under E000734
Checks
- 1Check the injector solenoid driver cylinder 5 circuit connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E000655 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Develon E000656Injector solenoid driver cylinder 6 circuit
Same failure as E000734 on the injector solenoid driver cylinder 6 circuit, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Injector solenoid driver cylinder 6 circuit'. The Isuzu engine table words this code as "Injection Nozzle #6Drive System Open Circuit Fault", so confirm against the table for your engine.· Open circuitOpen circuitCheck soonCauses
- Fault in the injector solenoid driver cylinder 6 circuit or its wiring
- Any cause listed under E000734
Checks
- 1Check the injector solenoid driver cylinder 6 circuit connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E000656 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Develon E000734Solenoid powerstage 1 (Cylinder 1)
A solenoid power stage for an injector cylinder is not working as commanded. That injector may not fire correctly, so the cylinder runs weak or drops out.· OtherOtherCheck soonCauses
- Open or shorted injector wiring or connector
- Faulty injector coil
- Driver fault in the controller
Checks
- 1Check the injector connector for oil, corrosion and a loose pin.
- 2Measure injector coil resistance and compare with the manual.
- 3Run the cylinder cut-out test in the tool to confirm which cylinder is weak.
- 4Inspect the injector harness under the valve cover for rubbing.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E000735Solenoid powerstage 2 (Cylinder 5)
Same failure as E000734 on the solenoid powerstage 2 (cylinder 5), a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Solenoid powerstage 2 (Cylinder 5)'.· OtherOtherCheck soonCauses
- Fault in the solenoid powerstage 2 (cylinder 5) or its wiring
- Any cause listed under E000734
Checks
- 1Check the solenoid powerstage 2 (cylinder 5) connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E000735 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E000736Solenoid powerstage 3 (Cylinder 3)
Same failure as E000734 on the solenoid powerstage 3 (cylinder 3), a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Solenoid powerstage 3 (Cylinder 3)'.· OtherOtherCheck soonCauses
- Fault in the solenoid powerstage 3 (cylinder 3) or its wiring
- Any cause listed under E000734
Checks
- 1Check the solenoid powerstage 3 (cylinder 3) connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E000736 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E000737Solenoid powerstage 4 (Cylinder 6)
Same failure as E000734 on the solenoid powerstage 4 (cylinder 6), a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Solenoid powerstage 4 (Cylinder 6)'.· OtherOtherCheck soonCauses
- Fault in the solenoid powerstage 4 (cylinder 6) or its wiring
- Any cause listed under E000734
Checks
- 1Check the solenoid powerstage 4 (cylinder 6) connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E000737 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E000738Solenoid powerstage 5 (Cylinder 2)
Same failure as E000734 on the solenoid powerstage 5 (cylinder 2), a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Solenoid powerstage 5 (Cylinder 2)'.· OtherOtherCheck soonCauses
- Fault in the solenoid powerstage 5 (cylinder 2) or its wiring
- Any cause listed under E000734
Checks
- 1Check the solenoid powerstage 5 (cylinder 2) connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E000738 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E000739Solenoid powerstage 6 (Cylinder 4)
Same failure as E000734 on the solenoid powerstage 6 (cylinder 4), a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Solenoid powerstage 6 (Cylinder 4)'.· OtherOtherCheck soonCauses
- Fault in the solenoid powerstage 6 (cylinder 4) or its wiring
- Any cause listed under E000734
Checks
- 1Check the solenoid powerstage 6 (cylinder 4) connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E000739 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001322Monitoring Misfire detection multiple cylinder
Same failure as E001323 on the monitoring misfire detection multiple cylinder, a different part of the same kind as the injection misfire detection cylinder 1. Specific to this code: the table names it 'Monitoring Misfire detection multiple cylinder'.· OtherOtherCheck soonCauses
- Fault in the monitoring misfire detection multiple cylinder or its wiring
- Any cause listed under E001323
Checks
- 1Check the monitoring misfire detection multiple cylinder connector and wiring first, then follow the checks listed under E001323.
- 2Clear the code and confirm whether E001322 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001323Injection Misfire detection cylinder 1
The misfire monitor recorded combustion trouble in one cylinder. It usually feels like rough idle, noise and loss of power.· OtherOtherCheck soonCauses
- Weak or sticking injector
- Poor compression in that cylinder
- Injector wiring fault
- Fuel leak at that injector
Checks
- 1Read the live misfire counts and compare the cylinders.
- 2Look for fuel leaks and injector return flow.
- 3Check the injector harness and connector.
- 4Check compression and valve condition if the misfire stays with the cylinder.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001324Injection Misfire detection cylinder 5
Same failure as E001323 on the injection misfire detection cylinder 5, a different part of the same kind as the injection misfire detection cylinder 1. Specific to this code: the table names it 'Injection Misfire detection cylinder 5'.· OtherOtherCheck soonCauses
- Fault in the injection misfire detection cylinder 5 or its wiring
- Any cause listed under E001323
Checks
- 1Check the injection misfire detection cylinder 5 connector and wiring first, then follow the checks listed under E001323.
- 2Clear the code and confirm whether E001324 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001325Injection Misfire detection cylinder 3
Same failure as E001323 on the injection misfire detection cylinder 3, a different part of the same kind as the injection misfire detection cylinder 1. Specific to this code: the table names it 'Injection Misfire detection cylinder 3'.· OtherOtherCheck soonCauses
- Fault in the injection misfire detection cylinder 3 or its wiring
- Any cause listed under E001323
Checks
- 1Check the injection misfire detection cylinder 3 connector and wiring first, then follow the checks listed under E001323.
- 2Clear the code and confirm whether E001325 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001326Injection Misfire detection cylinder 6
Same failure as E001323 on the injection misfire detection cylinder 6, a different part of the same kind as the injection misfire detection cylinder 1. Specific to this code: the table names it 'Injection Misfire detection cylinder 6'.· OtherOtherCheck soonCauses
- Fault in the injection misfire detection cylinder 6 or its wiring
- Any cause listed under E001323
Checks
- 1Check the injection misfire detection cylinder 6 connector and wiring first, then follow the checks listed under E001323.
- 2Clear the code and confirm whether E001326 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001327Injection Misfire detection cylinder 2
Same failure as E001323 on the injection misfire detection cylinder 2, a different part of the same kind as the injection misfire detection cylinder 1. Specific to this code: the table names it 'Injection Misfire detection cylinder 2'.· OtherOtherCheck soonCauses
- Fault in the injection misfire detection cylinder 2 or its wiring
- Any cause listed under E001323
Checks
- 1Check the injection misfire detection cylinder 2 connector and wiring first, then follow the checks listed under E001323.
- 2Clear the code and confirm whether E001327 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E001328Injection Misfire detection cylinder 4
Same failure as E001323 on the injection misfire detection cylinder 4, a different part of the same kind as the injection misfire detection cylinder 1. Specific to this code: the table names it 'Injection Misfire detection cylinder 4'.· OtherOtherCheck soonCauses
- Fault in the injection misfire detection cylinder 4 or its wiring
- Any cause listed under E001323
Checks
- 1Check the injection misfire detection cylinder 4 connector and wiring first, then follow the checks listed under E001323.
- 2Clear the code and confirm whether E001328 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E010003Injection Nozzle Common 1 Drive System Fault
Same failure as E000734 on the injection nozzle common 1 drive system fault, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Injection Nozzle Common 1 Drive System Fault'.· OtherOtherCheck soonCauses
- Fault in the injection nozzle common 1 drive system fault or its wiring
- Any cause listed under E000734
Checks
- 1Check the injection nozzle common 1 drive system fault connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E010003 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E010004Injection Nozzle Common 2 Drive System Fault
Same failure as E000734 on the injection nozzle common 2 drive system fault, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Injection Nozzle Common 2 Drive System Fault'.· OtherOtherCheck soonCauses
- Fault in the injection nozzle common 2 drive system fault or its wiring
- Any cause listed under E000734
Checks
- 1Check the injection nozzle common 2 drive system fault connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E010004 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E010005Charge Circuit Fault Bank 1
Same failure as E000734 on the charge circuit fault bank 1, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Charge Circuit Fault Bank 1'.· OtherOtherCheck soonCauses
- Fault in the charge circuit fault bank 1 or its wiring
- Any cause listed under E000734
Checks
- 1Check the charge circuit fault bank 1 connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E010005 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E010006Charge Circuit Fault Bank 2
Same failure as E000734 on the charge circuit fault bank 2, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Charge Circuit Fault Bank 2'.· OtherOtherCheck soonCauses
- Fault in the charge circuit fault bank 2 or its wiring
- Any cause listed under E000734
Checks
- 1Check the charge circuit fault bank 2 connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E010006 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E010032QR Code Error
Same failure as E000734 on the qr code error, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'QR Code Error'.· OtherOtherCheck soonCauses
- Fault in the qr code error or its wiring
- Any cause listed under E000734
Checks
- 1Check the qr code error connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E010032 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E520624Monitoring of injection
Same failure as E000734 on the monitoring of injection, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Monitoring of injection'.· OtherOtherCheck soonCauses
- Fault in the monitoring of injection or its wiring
- Any cause listed under E000734
Checks
- 1Check the monitoring of injection connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E520624 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Develon E520626Injection bank
Same failure as E000734 on the injection bank, a different part of the same kind as the solenoid powerstage 1 (cylinder 1). Specific to this code: the table names it 'Injection bank'.· OtherOtherCheck soonCauses
- Fault in the injection bank or its wiring
- Any cause listed under E000734
Checks
- 1Check the injection bank connector and wiring first, then follow the checks listed under E000734.
- 2Clear the code and confirm whether E520626 returns on its own.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Note the cylinder number in the code and compare its misfire count with the others.
- 2Inspect the injector harness and connector for oil, rub marks and corrosion.
- 3Run the cylinder cut-out or injector test, if the tool allows.
- 4Check compression and valve condition if the misfire stays with the cylinder.
Causes
- Injector coil or wiring fault
- Worn or sticking injector
- Driver or charge-circuit fault in the controller
Most common here: open circuit (6 of 26)
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
When to stop
You'll notice: Rough running, white or black smoke, noise and loss of power; the code usually names the cylinder.
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
