EF Logo

Develon · Pressure sensors

Develon Pump, pilot and brake pressure sensors fault codes

Pressure transducers on the pump outlets, the pilot circuits and the parking brake. The controller reads them to control pump power, protect the system and decide when the machine is allowed to move.

FaultCheckV000237Develon · Pump, pilot and brake pressure sensors
Code shows hereFAULTV000237

Where this code shows

Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.

What do these codes mean?

Develon codes V000237 to V000242 are all about the pump, pilot and brake pressure sensors. None needs an immediate stop. Start with this check: check the 5 V supply and ground at the sensor connector with the key on.

How urgent are they?

None of the 6 codes here means stop now; all 6 can wait until the shift ends, but find the cause before the next one.

  • Check soon6

What should I check first?

Check the 5 V supply and ground at the sensor connector with the key on.

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Develon V000237Front pump pressure sensor

    The front pump pressure sensor measures the outlet pressure of the front main pump.· Other
    Check soon

    Causes

    • Failed pressure sensor
    • Lost 5 V supply or sensor ground
    • Open or shorted signal wire
    • Water in the connector
    • Real pressure outside the sensor range from a hydraulic fault

    Checks

    1. 1Check the 5 V supply and ground at the sensor connector with the key on.
    2. 2Read the signal with the engine off; it should sit near the low end of the usual 0.5-4.5 V range and rise when the engine runs under load.
    3. 3Compare the monitor pressure reading with a test gauge if one can be fitted.
    4. 4Reseat the connector and inspect for moisture and bent pins.
    5. 5Swap with the rear pump sensor, if the type matches, to see whether the code follows the part.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V000238Rear pump pressure sensor

    Same failure as V000237 on the rear pump pressure sensor, a different part of the same kind as the front pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the rear pump pressure sensor or its wiring
    • Any cause listed under V000237

    Checks

    1. 1Check the rear pump pressure sensor connector and wiring first, then follow the checks listed under V000237.
    2. 2Clear the code and confirm whether V000238 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V000239OWD pressure sensor

    Same failure as V000237 on the owd pressure sensor, a different part of the same kind as the front pump pressure sensor.· Real condition
    Check soon

    Causes

    • Fault in the owd pressure sensor or its wiring
    • Any cause listed under V000237

    Checks

    1. 1Check the owd pressure sensor connector and wiring first, then follow the checks listed under V000237.
    2. 2Clear the code and confirm whether V000239 returns on its own.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Develon V000240Px(FRONT) pressure SENSOR

    Same failure as V000237 on the px(front) pressure sensor, a different part of the same kind as the front pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the px(front) pressure sensor or its wiring
    • Any cause listed under V000237

    Checks

    1. 1Check the px(front) pressure sensor connector and wiring first, then follow the checks listed under V000237.
    2. 2Clear the code and confirm whether V000240 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V000241Py(TRAVEL) pressure SENSOR

    Same failure as V000237 on the py(travel) pressure sensor, a different part of the same kind as the front pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the py(travel) pressure sensor or its wiring
    • Any cause listed under V000237

    Checks

    1. 1Check the py(travel) pressure sensor connector and wiring first, then follow the checks listed under V000237.
    2. 2Clear the code and confirm whether V000241 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V000242Parking brake pressure sensor

    Same failure as V000237 on the parking brake pressure sensor, a different part of the same kind as the front pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the parking brake pressure sensor or its wiring
    • Any cause listed under V000237

    Checks

    1. 1Check the parking brake pressure sensor connector and wiring first, then follow the checks listed under V000237.
    2. 2Clear the code and confirm whether V000242 returns on its own.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Check the 5 V supply and ground at the sensor connector with the key on.
  2. 2Compare the monitor pressure reading at rest with the expected near-zero value.
  3. 3Reseat and inspect the connector for moisture or bent pins.
  4. 4Swap with a sensor of the same type from another position to see if the code follows.

Causes

  • Failed pressure sensor
  • Damaged sensor wiring or water in the connector
  • Lost 5 V supply or sensor ground
  • Real over- or under-pressure from a hydraulic fault

When to stop

You'll notice: Power or response may drop and the monitor shows the code.

Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.