Thermo King alarm codes
Thermo King truck and trailer units show an alarm as a number on the controller display, with a bracket around codes that clear themselves. These are the North American alarm codes Thermo King publishes.
285 codes in 15 families49 stop now, 133 check soon, 103 info
285 Thermo King codes - type a code, or a word from the problem.
Covers Reefer trucks, Reefer trailers.
Where to look
- 01Press the alarm key or open the Alarms menu on the controller display to list active…
- 02Write down every alarm number, because one fault often raises several, and fix the…
- 03Look at the code in the list below to see which circuit or sensor it points at, and…
- 04Clear the alarm from the Alarms menu after the repair.
- 05Run a pretrip test and confirm the alarm does not come back.
How to read Thermo King alarm codes, in full
- Press the alarm key or open the Alarms menu on the controller display to list active alarms.
- Write down every alarm number, because one fault often raises several, and fix the earliest or most basic one first.
- Look at the code in the list below to see which circuit or sensor it points at, and check that part before replacing anything.
- Clear the alarm from the Alarms menu after the repair; some alarms (3, 4, 74, 203, 204) must be cleared from the Maintenance or Guarded Access menu.
- Run a pretrip test and confirm the alarm does not come back.
How urgent is a Thermo King code?
- Stop now49 codes
- Shut down and fix before working on. Running on risks damage or the machine locks out.
- Check soon133 codes
- The machine may derate or limit a function. Find the cause before the next shift.
- Information103 codes
- A reminder or status message. Nothing is failing yet.
Pick your system
Find the part of the machine, then the family your code belongs to.
- Code range
- The first and last code in the family, as the machine shows them.
- Codes
- How many codes the family holds; each is explained on its page.
- Severity mix
- The share of stop, check and info codes. The dot after it is the most urgent one in the family.
Temperature sensors (SR-2/SR-3/SR-4)21 codes
Refrigeration system (SR-2/SR-3/SR-4)23 codes
Temperature control (SR-2/SR-3/SR-4)18 codes
Compressor and valves (SR-2/SR-3/SR-4)21 codes
Engine speed and starting (SR-2/SR-3/SR-4)23 codes
Engine protection (SR-2/SR-3/SR-4)23 codes
Engine ECU faults (SR-2/SR-3/SR-4)49 codes
Charging system (SR-2/SR-3/SR-4)22 codes
Electric standby (SR-2/SR-3/SR-4)18 codes
Controller (SR-2/SR-3/SR-4)19 codes
Maintenance reminders (SR-2/SR-3/SR-4)12 codes
Communications and modules (SR-2/SR-3/SR-4)24 codes
Cryogenic CR units12 codes
Most searched Thermo King codes
- 02Check evaporator coil sensor
- 03Check return air sensor
- 04Check discharge air sensor
- 05Check ambient temperature sensor
- 06Check coolant temperature sensor
- 07Check engine RPM sensor
- 10High discharge pressure or temperature
- 14Defrost terminated by time
- 15Check glow plugs or intake air heater
- 17Engine failed to crank
- 18High engine coolant temperature
- 19Low engine oil pressure
- 20Engine failed to start
- 23Cooling cycle fault
- 25Alternator check
- 26Check refrigeration capacity
- 31Check oil pressure switch
- 32Refrigeration capacity low
- 36Electric motor failed to run
- 37Check engine coolant level
- 38Electric phase reversed
- 44Check fuel system
- 48Check belts or clutch
- 61Low battery voltage
- 63Engine or vapor motor stopped
- 66Low engine oil level
- 74Controller reset to defaults
- 81High compressor temperature
- 82High compressor temperature shutdown
- 84Restart null
- 86Check discharge pressure sensor
- 87Check suction pressure sensor
- 89Check electronic throttling valve (ETV) circuit
- 90Electric overload
- 91Check electric ready input
- 93Low compressor suction pressure
- 96Low fuel level
- 108Door open timeout
- 115Check high pressure cutout switch
- 128Engine run time maintenance reminder 1 / service due
- 144Lost CAN communications to expansion module
- 150Sensor out of range low
- 151Sensor out of range high
- 155Lost CAN communications to HMI
- 159Check battery condition
- 203Check display return air sensor
- 204Check display discharge air sensor
- 600Check crankshaft speed sensor
- 601Check camshaft speed sensor
- 608Check rail pressure sensor
- 611Check glow plug circuit
- 613Check injectors
- 615Rail pressure fault
- 616Engine overspeed
- 618Check EGR system
- 620No RPM detected during start attempt
- 844Engine failed to crank (engine ECU)
Quick answers
How do I read Thermo King alarm codes?
Press the alarm key or open the Alarms menu on the controller display to list active alarms. Write down every alarm number, because one fault often raises several, and fix the earliest or most basic one first.
Which Thermo King codes mean stop now?
49 of the 285 Thermo King codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example 03, 07, 10, 17. 133 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.
What should I check first on a Thermo King code?
Most Thermo King codes here (27 of 285) read as real condition: the sensor reading is valid but outside the allowed range - the problem may be real. First test, as general workshop practice: check the real value with a separate gauge or thermometer before blaming the sensor.
Sources
Every code was read from these documents and written in our own words.
Other makers
Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.
Post a request