Thermo King · Charging system (SR-2/SR-3/SR-4)
Thermo King Alternator, battery and battery charger fault codes
This page covers the charging system: alternator and battery alarms, and the battery charger input, output, electrical, temperature and status alarms. The alternator charges the unit battery and the controller watches the voltage.
More about these partsLess
The on-board battery charger takes mains power and charges the unit battery. These alarms report electrical faults in the battery charger: shorts, overvoltage and out of range voltages. These alarms report the battery charger temperature and status: low temperature, derating, charging a low battery and sensor faults.
Where this code shows
Press the alarm key or open the Alarms menu on the controller display to list active alarms.
What do these codes mean?
Thermo King codes bAt to 553 are all about the alternator, battery and battery charger. The most common failure type is shorted low (2 of 22); 1 needs an immediate stop. Start with this check: measure the battery voltage at rest and with the engine running.
How urgent are they?
1 of 22 codes here means stop now; 11 can wait until the shift ends, but find the cause before the next one; 10 are information only.
- Stop now1
- Check soon11
- Info10
What should I check first?
Measure the battery voltage at rest and with the engine running
Shared checks22 of 22
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Thermo King bAtLow battery voltage
The battery voltage is low. The unit may stop if it falls further.· Shorted lowShorted lowStop nowCauses
- Weak battery
- Alternator not charging
Checks
- 1Measure the battery voltage
- 2Check the alternator output
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Thermo King 25Alternator check
The charging output from the unit alternator is wrong, either not charging at all or giving a voltage the controller does not accept. The battery will eventually go flat.· OtherOtherCheck soonCauses
- Alternator drive belt loose or broken
- Alternator excite wire open or its fuse blown
- Voltage regulator failed
- Battery cables corroded
Checks
- 1Check the alternator belt tension and condition
- 2Measure battery voltage with the engine running
- 3Watch battery voltage with the engine running; it should rise above its resting voltage
- 4Check the excite circuit wire and fuse at the alternator
- 5Clean the battery cables and the main alternator output lug
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 61Low battery voltage
The battery voltage seen by the controller dropped below the minimum it needs, risking a failed start or controller reset.· OtherOtherCheck soonCauses
- Battery discharged or worn
- Charging system not working
- Corroded or loose cables
Checks
- 1Load test the battery and check its age, since old batteries fail under cranking load
- 2Check the alternator output with the engine running
- 3Clean and tighten the battery cables and the engine ground strap
- 4Check for a parasitic drain with the unit off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 120Check alternator excite circuit
A fault is found in the alternator excite circuit, which the controller uses to turn the alternator on.· OtherOtherCheck soonCauses
- Excite wire open or shorted
- Fuse blown
- Alternator regulator fault
Checks
- 1Check the alternator excite wire and its fuse for continuity
- 2Measure the voltage at the alternator excite terminal with the key on
- 3Check the voltage regulator in the alternator for correct operation
- 4Inspect the alternator connector for corrosion and loose terminals
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 159Check battery condition
The controller judged the battery condition to be poor, for example low voltage after starting or a battery that does not recover between starts.· Shorted lowShorted lowCheck soonCauses
- Battery aged and unable to hold charge
- Charging system output low
- Loose or corroded terminals
- Parasitic load draining the battery
Checks
- 1Load test the battery and check its state of charge
- 2Measure the alternator output with the engine running
- 3Clean the terminals and check cable lugs for heat discoloration
- 4Check for any accessory load left switched on while the unit is parked and off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Thermo King 519Battery charger input power check
The input power to the battery charger is out of range. The charger may not charge the unit battery.· OtherOtherCheck soonCauses
- Supply plug or cable damaged
- Low supply voltage
Checks
- 1Check the supply voltage and cable to the charger
- 2Check the charger input fuse
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 520Battery charger output power check
The output power of the battery charger is out of range. The battery may not get charged.· OtherOtherCheck soonCauses
- Output cable damaged
- Charger failure
Checks
- 1Check the output cable and battery connection
- 2Measure the charger output voltage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 521Battery charger external or environmental fault
The charger reports an external or environmental cause such as heat or a wiring fault outside the charger.· OtherOtherCheck soonCauses
- High ambient temperature
- Wiring fault
Checks
- 1Check the charger surroundings and wiring
- 2Let it cool and recheck
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 522Battery temperature sensor alarm
The battery temperature sensor used by the charger gives an out-of-range reading. Charging cannot be corrected for temperature.· OtherOtherCheck soonCauses
- Sensor wire damaged
- Sensor failed
Checks
- 1Check the sensor wire and plug
- 2Measure the sensor resistance
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 523Battery charger indicated conditions
The charger reports a general condition that the controller flags as an alarm. Read the charger display for the actual fault.· OtherOtherCheck soonCauses
- Charger internal condition
- Supply fault
Checks
- 1Read the charger status and codes
- 2Check the supply
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 528Failed J1939 CAN communication base controller to charger
The controller and the battery charger cannot talk over the J1939 CAN link. Charger information is lost.· Lost messageLost messageCheck soonCauses
- CAN wire damaged
- Charger supply lost
Checks
- 1Check the CAN wires and plugs
- 2Check the charger supply
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Thermo King 542Battery charger fault: unit forced to low speed
The battery charger has a fault that forces the unit to low speed. It is maintenance information only.· OtherOtherInfoCauses
- Charger fault
- Battery fault
Checks
- 1Read the charger status
- 2Check the battery condition
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 543Battery charger internal short
The battery charger reports an internal short circuit. It is maintenance information only.· Short circuitShort circuitInfoCauses
- Charger internal fault
- Water in the charger
Checks
- 1Check the charger for damage
- 2Replace the charger if the alarm remains
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
Thermo King 544Battery charger external short
The battery charger reports a short circuit outside the charger on the output side.· Short circuitShort circuitInfoCauses
- Output cable shorted
- Battery terminal shorted
Checks
- 1Check the output cable and terminals for shorts
- 2Measure the output resistance
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
Thermo King 545Battery charger output voltage exceeded limit
The battery charger output voltage went above its limit. It is maintenance information only.· Real conditionReal conditionInfoCauses
- Charger regulator fault
- Battery disconnected during charging
Checks
- 1Check the battery connection
- 2Measure the charger output voltage
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Thermo King 546Battery charger operating bulk voltage out of range
The bulk charging voltage of the charger is outside its range. The battery may not charge correctly.· OtherOtherInfoCauses
- Charger regulator fault
- Poor battery connection
Checks
- 1Measure the charger bulk voltage
- 2Check the battery connection
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 548Battery charger temperature below operating range
The temperature of the battery charger is below its operating range, as in cold weather. Charging may be delayed.· OtherOtherInfoCauses
- Very low ambient temperature
- Temperature sensor fault
Checks
- 1Check the ambient temperature
- 2Check the charger sensor
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 549Battery charger AC input overvoltage
The AC voltage to the charger is above its limit. The charger may stop until the supply returns to normal.· OtherOtherInfoCauses
- Supply voltage too high
- Generator or site supply fault
Checks
- 1Measure the AC supply voltage
- 2Check the source of the supply
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 550Battery charger internal overvoltage fault
The charger detected an overvoltage inside itself. The charger stops to protect the battery.· OtherOtherCheck soonCauses
- Charger internal fault
- Battery connection loose
Checks
- 1Check the battery connection
- 2Replace the charger if the fault returns
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 551Battery charger internal temperature sensor fault
The temperature sensor inside the charger is faulty. The charger cannot protect itself from heat.· OtherOtherInfoCauses
- Sensor failed
- Charger internal fault
Checks
- 1Check the charger for other alarms
- 2Replace the charger if the alarm remains
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 552Battery charger charging, low battery
The charger reports that it is charging a low battery. It is a status message.· OtherOtherInfoCauses
- Battery discharged
- Battery weak
Checks
- 1Let the battery charge and recheck
- 2Test the battery
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 553Battery charger operating derated due to high temperature
The charger reduces its output because it is hot. Charging takes longer.· Real conditionReal conditionInfoCauses
- High ambient temperature
- Charger cooling blocked
Checks
- 1Check the charger cooling
- 2Allow it to cool
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Measure the battery voltage at rest and with the engine running
- 2Check the supply voltage at the charger input with a meter
- 3Check the output cable and terminals for shorts
- 4Check the ambient temperature around the charger
- 5Check the drive belt and the battery terminals
- 6Check the output cable and battery connection for corrosion
- 7Check the battery connection is secure and clean
Causes
- Weak battery
- Supply cable damaged
- Short in the output
- Extreme temperature
Most common here: shorted low (2 of 22)
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
When to stop
You'll notice: Low battery or alternator alarms and, in the worst case, the engine not starting.
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
