Thermo King · Engine protection (SR-2/SR-3/SR-4)
Thermo King Fault Code 19
Low engine oil pressure
What does Thermo King code 19 mean?
The engine oil pressure signal dropped below the protection limit. The controller stops the engine to prevent wear because low oil pressure can wreck bearings fast. Urgency: stop now - shut down and fix before working on. Check first: check the dipstick level and look at the oil for fuel dilution.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Check the dipstick level and look at the oil for fuel dilution
Then 4 more checksWhere this code shows
Press the alarm key or open the Alarms menu on the controller display to list active alarms.
Checks
0 of 5 done
Causes
- Engine oil level low
- Oil pressure switch or sender failed
- Wrong or diluted oil
- Worn oil pump or bearings
1 more causeFewer causes
- Blocked oil filter
How it failed
You'll notice: Alarm 19 and the engine shuts down, sometimes soon after starting; the oil lamp may light if fitted.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Low oil pressure can wreck bearings in minutes. Stop the engine and check the level before restarting; if the level is right, do not run it again until the pressure is checked with a gauge.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine coolant, oil, overspeed, fuel and ECU temperature sensors
1 other code on this part is also lost message (83). When they show together, start at the wiring and connector they share.
- 06Check coolant temperature sensorReal conditionCheck soon
- 18High engine coolant temperatureOtherStop now
- 19Low engine oil pressureLost messageStop now
- 31Check oil pressure switchReal conditionCheck soon
- 37Check engine coolant levelReal conditionStop now
- 41Check engine coolant temperatureOtherCheck soon
- 44Check fuel systemOtherStop now
- 63Engine or vapor motor stoppedOtherStop now
- 66Low engine oil levelOtherCheck soon
Show the other 14 codesHide the other codes
- 83Low engine coolant temperatureLost messageInformation
- 96Low fuel levelOtherCheck soon
- 98Check fuel level sensorOtherCheck soon
- 235High engine coolant temperature checkOtherInformation
- 254Auxiliary coolant temperature sensor checkOtherInformation
- 529Check fuel pump circuitOtherStop now
- 604Check coolant temperature sensor (engine ECU)OtherCheck soon
- 607Fuel temperature sensor checkOtherInformation
- 616Engine overspeedReal conditionStop now
- 804Engine coolant temperature sensor errorOtherInformation
- 807Fuel temperature sensor errorOtherInformation
- 834Water in fuel sensor errorOtherInformation
- 853Engine overspeed (no DTC)Real conditionCheck soon
- 854Engine protection self shutdownReal conditionStop now
Other Thermo King codes: Engine protection (SR-2/SR-3/SR-4)
Source
Thermo King Alarm Codes - North America (thermoking.com alarm code list)
This source lists 19 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Thermo King SR-2, SR-3, SR-4 truck and trailer units and related Thermo King controllers (the families the source lists).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
