EF Logo

Thermo King · Engine protection (SR-2/SR-3/SR-4)

Thermo King Engine coolant, oil, overspeed, fuel and ECU temperature sensors fault codes

This page covers engine protection: overheat and low coolant, oil pressure and level, overspeed and protective shutdown, the fuel system and level, and the engine ECU coolant and fuel temperature sensors. The unit controller compares the engine coolant temperature and level against its limits.

More about these parts

The oil pressure switch and the oil level sensor protect the engine from running dry. These alarms report that the engine stopped or ran above its allowed speed, or that the engine protection shut the engine down by itself. These alarms cover the fuel supply to the engine: a general fuel system check, the fuel level and its sensor, the fuel pump circuit and the water-in-fuel sensor. The engine ECU has its own coolant, auxiliary coolant and fuel temperature sensors, separate from the unit controller protection alarms.

FaultStop18Thermo King · Engine coolant, oil, overspeed, fuel and ECU temperature sensors
Code shows hereFAULT18

Where this code shows

Press the alarm key or open the Alarms menu on the controller display to list active alarms.

What do these codes mean?

Thermo King codes 06 to 854 are all about the engine coolant, oil, overspeed, fuel and ECU temperature sensors. The most common failure type is real condition (6 of 23); 8 need an immediate stop. Start with this check: with the engine cold, check the coolant bottle and radiator level and look for wet spots at hoses, pump and radiator.

How urgent are they?

8 of 23 codes here mean stop now; 8 can wait until the shift ends, but find the cause before the next one; 7 are information only.

  • Stop now8
  • Check soon8
  • Info7

What should I check first?

With the engine cold, check the coolant bottle and radiator level and look for wet spots at hoses, pump and radiator

Shared checks

23 of 23

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Thermo King 06Check coolant temperature sensor

    The engine coolant temperature sensor signal is out of range, so the controller cannot protect the engine against overheating or confirm the engine has warmed up.· Real condition
    Check soon

    Causes

    • Coolant sensor at the engine thermostat housing has a bad connector
    • Wire damaged by engine heat or vibration
    • Sensor failed open or shorted
    • Corrosion in the engine harness plug

    Checks

    1. 1Find the coolant sensor on the engine and inspect its connector and wires for heat damage
    2. 2Measure resistance at the sensor with the engine cold and compare to ambient
    3. 3Check the harness for continuity back to the controller
    4. 4Look for short to ground with the sensor unplugged
    5. 5Warm the engine and watch if the reading moves smoothly or jumps
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Thermo King 18High engine coolant temperature

    Engine coolant went above the controller limit.· Other
    Stop now

    Causes

    • Low coolant from a leak
    • Radiator or condenser airflow blocked
    • Fan belt loose or water pump worn
    • Thermostat stuck closed
    • Coolant sensor reading false high

    Checks

    1. 1Let the engine cool, then check coolant level and look for leaks
    2. 2Inspect the radiator fins and the engine fan belt tension
    3. 3Check that the thermostat opens as the engine warms
    4. 4Compare the displayed temperature with an infrared thermometer on the housing
    5. 5Pressure test the cooling system and check the water pump
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 19Low engine oil pressure

    The engine oil pressure signal dropped below the protection limit.· Lost message
    Stop now

    Causes

    • Engine oil level low
    • Oil pressure switch or sender failed
    • Wrong or diluted oil
    • Worn oil pump or bearings
    • Blocked oil filter

    Checks

    1. 1Check the dipstick level and look at the oil for fuel dilution
    2. 2Compare the switch with a mechanical gauge fitted in the oil port
    3. 3Check the oil pressure switch wiring for chafing or a short
    4. 4Change the oil and filter if the service is overdue
    5. 5Investigate pump and bearings if the gauge shows real low pressure
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Thermo King 31Check oil pressure switch

    The engine oil pressure switch input does not make sense: the switch state conflicts with the engine running state, which suggests a switch or wiring fault rather than real low pressure.· Real condition
    Check soon

    Causes

    • Oil pressure switch failed open or stuck
    • Switch wire shorted to ground
    • Connector at the engine corroded

    Checks

    1. 1Check the switch state with the engine off and then running
    2. 2Test continuity of the switch wire to the controller
    3. 3Compare with a mechanical oil gauge to rule out real pressure loss
    4. 4Replace the switch if it does not change state
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Thermo King 37Check engine coolant level

    The coolant level sensor or switch indicates the engine coolant is too low.· Real condition
    Stop now

    Causes

    • Coolant leak at hose, radiator or water pump
    • Coolant not topped up after service
    • Level sensor fouled or failed

    Checks

    1. 1Check the coolant overflow bottle and radiator level when cold
    2. 2Look for wet spots at hoses, pump and radiator
    3. 3Test the level sensor by raising the level and watching the alarm clear
    4. 4Pressure test the cooling system for slow leaks
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Thermo King 41Check engine coolant temperature

    The coolant temperature reading is outside the range the controller expects, which may be a sensor fault or a real temperature problem.· Other
    Check soon

    Causes

    • Coolant sensor drifting
    • Wiring or connector fault
    • Thermostat stuck open or closed

    Checks

    1. 1Compare the display with a temperature probe on the engine
    2. 2Check the coolant sensor and its connector for corrosion or a loose terminal
    3. 3Check the thermostat opens as the engine warms
    4. 4Look for air pockets in the coolant that can give a false high reading at the sensor
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 44Check fuel system

    The controller found an issue in the fuel system, usually the fuel solenoid or supply, that prevents steady engine running.· Other
    Stop now

    Causes

    • Empty or low fuel tank
    • Clogged fuel filter or air in lines
    • Fuel solenoid failed
    • Fuel pump not working

    Checks

    1. 1Check fuel level and make sure the tank pickup is not drawing air or sludge
    2. 2Replace the fuel filter and bleed the air out of the system after the change
    3. 3Check the fuel solenoid for voltage and operation
    4. 4Check the lift pump delivers a steady flow and pressure at the filter head
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 63Engine or vapor motor stopped

    The controller saw the engine (or the vapor motor on CR units) stop while it was supposed to be running.· Other
    Stop now

    Causes

    • Fuel starvation from filter or air
    • Engine protection shutdown
    • Belt or compressor load stalling engine
    • Loose wiring cutting run power

    Checks

    1. 1Check the fuel level and the filter first, since fuel starvation is the common cause
    2. 2Read earlier alarms in the log for high temperature, pressure or oil
    3. 3Check the wiring at the run relay and fuel solenoid
    4. 4Check the compressor turns freely by hand with the belt off, to rule out a seized pump
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 66Low engine oil level

    The oil level sensor reports the engine oil is low.· Other
    Check soon

    Causes

    • Oil level genuinely low
    • Oil level sensor failure
    • Oil leak

    Checks

    1. 1Check the engine dipstick on level ground and top up to the full mark
    2. 2Look for oil leaks around the filter, sump gasket and valve cover
    3. 3Test the oil level sensor by comparing its output with the real oil level
    4. 4Check the oil consumption over a few hundred hours to see if the engine burns oil
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 83Low engine coolant temperature

    The engine coolant is not reaching its normal temperature, which can mean the thermostat is stuck open or the sensor is wrong.· Lost message
    Info

    Causes

    • Thermostat stuck open
    • Coolant sensor reading low
    • Very cold ambient with the engine lightly loaded

    Checks

    1. 1Check the thermostat opens at the correct temperature
    2. 2Compare the display with a probe on the engine
    3. 3Check the coolant sensor wiring for resistance or corrosion that shifts the reading
    4. 4Check the engine is not running too lightly in cold weather
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Thermo King 96Low fuel level

    The fuel level sensor reports the fuel tank is almost empty, so the unit will soon run out of fuel and stop cooling.· Other
    Check soon

    Causes

    • Tank is truly low on fuel
    • Fuel level sensor reading low
    • Fuel level wiring fault

    Checks

    1. 1Check the tank level with a dipstick or by eye
    2. 2Refill the tank and see whether the low fuel alarm clears on its own
    3. 3Check the level sensor reading against the actual level
    4. 4Inspect the level sensor wiring and connector for corrosion or damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 98Check fuel level sensor

    The fuel level sensor signal is outside its range, so the controller cannot read the fuel level.· Other
    Check soon

    Causes

    • Fuel sender wiring open or shorted
    • Sender float stuck
    • Connector corroded

    Checks

    1. 1Check the fuel sender plug and wires for corrosion or breaks at the tank
    2. 2Measure the sender resistance as the float moves
    3. 3Check the sender ground connection to the tank and chassis for resistance
    4. 4Replace the sender if the reading does not change
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 235High engine coolant temperature check

    A reminder that the engine coolant temperature has been high.· Other
    Info

    Causes

    • Coolant low or radiator dirty
    • Fan or belt problem

    Checks

    1. 1Check the coolant level and radiator
    2. 2Check the fan belt
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 254Auxiliary coolant temperature sensor check

    The auxiliary coolant temperature sensor is out of range.· Other
    Info

    Causes

    • Sensor wire damaged
    • Sensor failed

    Checks

    1. 1Check the sensor plug and lead
    2. 2Measure the sensor resistance
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 529Check fuel pump circuit

    The controller found a fault in the fuel pump circuit, the electric lift pump that feeds the engine.· Other
    Stop now

    Causes

    • Fuel pump failed
    • Pump wire or fuse open
    • Connector corroded

    Checks

    1. 1Check the pump fuse and relay for continuity and clean the holders
    2. 2Measure the voltage at the pump when run is commanded
    3. 3Listen for the fuel pump running for a few seconds at key on
    4. 4Check the pump connector at the tank for corrosion and loose pins
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 604Check coolant temperature sensor (engine ECU)

    The engine ECU sees its coolant temperature sensor outside its valid range, so it cannot correct fuel and glow time for engine temperature.· Other
    Check soon

    Causes

    • ECU coolant sensor connector corroded
    • Sensor failed open or shorted
    • Wire damaged near the thermostat housing

    Checks

    1. 1Unplug the ECU coolant sensor and measure its resistance cold, comparing with ambient
    2. 2Look at the sensor connector for green corrosion and a loose latch
    3. 3Test the wires for an open or a short to ground back to the ECU
    4. 4Check the live reading in the ECU data as the engine warms
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 607Fuel temperature sensor check

    The fuel temperature sensor is out of range.· Other
    Info

    Causes

    • Sensor lead damaged
    • Failed sensor

    Checks

    1. 1Check the sensor plug and lead
    2. 2Measure the sensor resistance
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 616Engine overspeed

    The engine speed went above the safe limit and the ECU logged an overspeed event, shutting the engine down.· Real condition
    Stop now

    Causes

    • Speed actuator or throttle stuck open
    • Runaway on oil from a leaking turbo or breather
    • Speed sensor fault giving false readings
    • Bad ECU control

    Checks

    1. 1Check the speed control linkage or actuator for sticking
    2. 2Look for oil entering the intake, such as a leaking turbo seal
    3. 3Compare the displayed speed with a handheld tachometer
    4. 4Read the ECU stored data for the overspeed event
    5. 5Check the speed sensor signal on the scope or with the service tool
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Thermo King 804Engine coolant temperature sensor error

    The engine ECU reports an error on the coolant temperature sensor.· Other
    Info

    Causes

    • Sensor wire damaged
    • Sensor failed

    Checks

    1. 1Check the sensor plug and lead
    2. 2Measure the sensor resistance
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 807Fuel temperature sensor error

    The fuel temperature sensor reports an error.· Other
    Info

    Causes

    • Sensor wire damaged
    • Sensor failed

    Checks

    1. 1Check the sensor plug and lead
    2. 2Measure the sensor resistance
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 834Water in fuel sensor error

    The water-in-fuel sensor reports a fault.· Other
    Info

    Causes

    • Sensor wire damaged
    • Water really in the fuel

    Checks

    1. 1Drain the fuel filter water trap
    2. 2Check the sensor plug and wiring
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 853Engine overspeed (no DTC)

    The engine ran above its allowed speed but no fault code was stored by the ECU.· Real condition
    Check soon

    Causes

    • Governor or speed signal fault
    • Loose speed sensor

    Checks

    1. 1Check the speed sensor and its wiring
    2. 2Compare the display speed with a tachometer
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Thermo King 854Engine protection self shutdown

    The engine ECU shut the engine down by itself to protect it from a condition such as overheating or low oil pressure.· Real condition
    Stop now

    Causes

    • High coolant temperature
    • Low oil pressure
    • ECU protection limit hit

    Checks

    1. 1Read the ECU stored faults for the cause of the self shutdown
    2. 2Check the coolant level and oil level and condition
    3. 3Check the temperature and pressure sensors for plausible readings
    4. 4Clear the faults and run the unit to see whether it trips again
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1With the engine cold, check the coolant bottle and radiator level and look for wet spots at hoses, pump and radiator
  2. 2Check the oil level on the dipstick on level ground
  3. 3Read the alarm list for the first alarm, since the shutdown is often the last in a chain
  4. 4Check the fuel level against the gauge and look at the fuel tank sender wiring
  5. 5Unplug the sensor and measure its resistance cold, then warm, to see that it falls as the engine heats
  6. 6Clean the radiator fins and check the fan belt tension
  7. 7Check the oil pressure with a mechanical gauge at the sender port

Causes

  • Coolant lost through a leak, or not topped up after service
  • Low oil level
  • Governor or speed signal fault
  • Fuel tank low or sensor reading wrongly

Most common here: real condition (6 of 23)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: High coolant temperature or low coolant alarm and, if ignored, an engine shutdown.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.