EF Logo

Thermo King · Engine ECU faults (SR-2/SR-3/SR-4)

Thermo King Engine ECU internal faults, enable signals and run relays fault codes

This page covers ECU internal faults, enable and run signals, and the run and shutdown relay circuits of the unit. The engine ECU needs an enable signal and a run signal from the controller and runs self-tests.

More about these parts

The controller switches the run relay and watches the shutdown circuit.

FaultStop35Thermo King · Engine ECU internal faults, enable signals and run relays
Code shows hereFAULT35

Where this code shows

Press the alarm key or open the Alarms menu on the controller display to list active alarms.

What do these codes mean?

Thermo King codes 35 to 899 are all about the engine ECU internal faults, enable signals and run relays. 2 need an immediate stop. Start with this check: check the enable and run signal wires and plugs between controller and ECU.

How urgent are they?

2 of 12 codes here mean stop now; 9 can wait until the shift ends, but find the cause before the next one; 1 is information only.

  • Stop now2
  • Check soon9
  • Info1

What should I check first?

Check the enable and run signal wires and plugs between controller and ECU

Shared checks

12 of 12

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Thermo King 35Check run relay circuit

    The controller found a problem with the run relay circuit that feeds power to the fuel solenoid and engine run circuits.· Other
    Stop now

    Causes

    • Run relay coil or contacts failed
    • Blown fuse in the run circuit
    • Wire from relay to fuel solenoid open

    Checks

    1. 1Check the run circuit fuse and replace it if blown
    2. 2Listen and test the relay for pull-in when run is commanded
    3. 3Measure voltage at the fuel solenoid with run active
    4. 4Check the relay socket terminals for burnt or spread pins that cause a poor contact
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 51Check shutdown circuit

    The controller found an issue in the shutdown circuit that cuts the fuel or run power to stop the engine.· Other
    Stop now

    Causes

    • Fuel solenoid hold circuit fault
    • Run relay failure
    • Wiring short in the shutdown line

    Checks

    1. 1Check the shutdown wire for shorts to supply or ground
    2. 2Test the fuel solenoid hold and pull-in coils
    3. 3Check the run relay pulls in and releases correctly when the unit starts and stops
    4. 4Test the related fuses for continuity and check their holders for heat damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 509ECU failed to enable

    The engine ECU did not switch on when the controller asked it to.· Other
    Check soon

    Causes

    • Enable wire open or shorted
    • ECU supply fuse or relay failed

    Checks

    1. 1Check the ECU enable wire and its fuse
    2. 2Check the ECU main relay and supply voltage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 510ECU run signal failed

    The run signal between the controller and the engine ECU failed while the engine was meant to run.· Other
    Check soon

    Causes

    • Run signal wire open or shorted
    • Connector problem at the ECU

    Checks

    1. 1Check the run signal wire and plug
    2. 2Monitor the run signal while cranking
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 540Illegal engine operating state

    The engine ECU or controller found the engine in a state that should not be possible, for example running without a request.· Other
    Check soon

    Causes

    • Faulty enable or run signal
    • ECU software fault

    Checks

    1. 1Check the enable and run signal wiring
    2. 2Cycle the unit power and see whether the alarm returns
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 599Engine service tool connected

    A service tool is connected to the engine ECU.· Other
    Info

    Causes

    • Diagnostic tool left plugged in
    • Faulty connector

    Checks

    1. 1Disconnect the service tool and restart the unit
    2. 2Check the diagnostic connector for a stuck pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 617Internal ECU fault

    The engine ECU detected a fault inside itself.· Lost message
    Check soon

    Causes

    • ECU internal failure
    • Unstable supply voltage

    Checks

    1. 1Check the battery voltage and ECU fuses
    2. 2Read the stored ECU codes with the service tool
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Thermo King 699Unknown ECU fault

    The engine ECU reported a fault code the controller does not know.· Other
    Check soon

    Causes

    • New ECU fault not listed in the controller
    • Software mismatch

    Checks

    1. 1Read the ECU fault codes with the service tool
    2. 2Compare the ECU and controller software versions
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 836Major ECU failures

    The engine ECU reports a serious internal failure.· Other
    Check soon

    Causes

    • ECU hardware failure
    • Water in the ECU connector

    Checks

    1. 1Check the ECU plug for water and corrosion
    2. 2Check supply voltage and earth
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 846T50 switch error

    The T50 switch input read by the engine ECU is faulty.· Other
    Check soon

    Causes

    • Switch wiring damaged
    • Switch failed

    Checks

    1. 1Check the T50 switch and its wiring
    2. 2Compare the input state with the display
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 847Variant coding error

    The engine ECU does not hold the right variant coding for this unit.· Other
    Check soon

    Causes

    • ECU replaced without coding
    • Software mismatch

    Checks

    1. 1Have the variant coding re-entered with the service tool
    2. 2Check the ECU part number against the unit
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 899Unknown ECU fault

    The engine ECU sent a fault code that is not in the controller table.· Other
    Check soon

    Causes

    • Fault code from a newer ECU
    • Software mismatch

    Checks

    1. 1Read the stored ECU codes with the service tool
    2. 2Check the software versions
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Check the enable and run signal wires and plugs between controller and ECU
  2. 2Swap the relay with a known good one of the same type
  3. 3Check the supply voltage and earths at the ECU
  4. 4Check the wiring and the fuse for the circuit
  5. 5Read the stored codes with the service tool
  6. 6Measure the relay coil resistance and the supply at the socket
  7. 7Have the ECU recoded or replaced by a Thermo King dealer

Causes

  • ECU internal failure
  • Relay failed
  • Enable or run signal wiring fault
  • Wiring fault

When to stop

You'll notice: The engine may not start or may stop, with the alarm on the display.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.