Thermo King · Engine ECU faults (SR-2/SR-3/SR-4)
Thermo King Engine ECU rail pressure, injectors and EGR fault codes
This page covers the engine ECU fuel and emission side: common rail pressure and pump, injectors and fuel injection, and EGR and emission control. The engine uses a high pressure pump and a common rail, with a pressure sensor and a regulator.
More about these partsLess
The engine ECU drives the injectors and watches the injection system. The exhaust gas recirculation valve, its actuator and its sensors, together with the emission control system, are watched by the engine ECU.
Where this code shows
Press the alarm key or open the Alarms menu on the controller display to list active alarms.
What do these codes mean?
Thermo King codes 163 to 843 are all about the engine ECU rail pressure, injectors and EGR. The most common failure type is real condition (4 of 16); 3 need an immediate stop. Start with this check: check the fuel supply, lift pump and filter first for restriction and air.
How urgent are they?
3 of 16 codes here mean stop now; 3 can wait until the shift ends, but find the cause before the next one; 10 are information only.
- Stop now3
- Check soon3
- Info10
What should I check first?
Check the fuel supply, lift pump and filter first for restriction and air
Shared checks16 of 16
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Thermo King 163Emission control failure
The controller recorded a fault in the engine emission control system, which on newer engines includes the EGR and related sensors.· OtherOtherCheck soonCauses
- EGR valve or its position sensor faulty
- Intake or exhaust sensor failure
- Engine ECU fault reporting an emission problem
Checks
- 1Read the engine ECU fault codes with the engine service tool
- 2Check the EGR valve and its connector for sticking or soot
- 3Look at the related temperature and pressure sensors for open or short circuits
- 4Clear the faults and run the engine under load to see if they come back
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 608Check rail pressure sensor
The common rail fuel pressure sensor reading is out of range, so the ECU cannot regulate fuel pressure with confidence.· OtherOtherStop nowCauses
- Rail pressure sensor connector wet or corroded
- Open or shorted sensor wire
- Sensor failed
- 5 V reference missing
Checks
- 1Check the rail pressure sensor plug for water and corrosion
- 2Measure the 5 V reference and the signal at the sensor
- 3Check the wires to the ECU for an open or short to ground
- 4Compare the displayed pressure with the engine off, where it should read near zero
- 5Inspect the rail and its fittings for fuel leaks or wetness
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 613Check injectors
The engine ECU found a problem in the injector circuit, such as an open or shorted injector coil.· OtherOtherStop nowCauses
- Injector coil open or shorted
- Injector connector corroded or loose
- Harness chafed at the valve cover
- ECU injector driver fault
Checks
- 1Measure each injector coil resistance and compare them
- 2Inspect the injector connectors and harness at the valve cover
- 3Run an injector cut-out test with the service tool
- 4Check the injector return flow if the manual lists a test
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 614High pressure fuel pump check
The engine ECU suspects the high pressure fuel pump is not delivering as expected. Rail pressure may be low or unstable.· Real conditionReal conditionInfoCauses
- Worn pump
- Air or restriction in the fuel supply
Checks
- 1Check the fuel supply, filter and lines
- 2Read the rail pressure with the service tool
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Thermo King 615Rail pressure fault
The common rail pressure is not following the target, either too low or too high, so the ECU has logged a rail pressure fault.· Real conditionReal conditionStop nowCauses
- Fuel filter blocked or air in the fuel
- High pressure pump worn
- Rail pressure regulator or relief valve leaking
- Injector leak-off high
Checks
- 1Replace the fuel filter and bleed the fuel system
- 2Check the supply pressure to the high pressure pump
- 3Read actual and target rail pressure while cranking
- 4Check injector return flow for excessive leakage
- 5Check the fuel for water or contamination in a clear sample
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Thermo King 618Check EGR system
The engine ECU found a problem in the exhaust gas recirculation system, such as the EGR valve not following its command.· OtherOtherCheck soonCauses
- EGR valve carbon-stuck
- EGR position sensor fault
- EGR valve actuator wiring damaged
- Blocked EGR cooler or pipe
Checks
- 1Command the EGR valve in the service tool and see if it moves
- 2Inspect the EGR valve connector and wiring for heat damage
- 3Remove the valve and look for carbon build-up
- 4Check the EGR cooler and pipe for blockage by soot
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 624EGR temperature sensor check
The EGR temperature sensor is out of range. The ECU cannot control recirculation correctly.· OtherOtherInfoCauses
- Sensor lead open or shorted
- Failed sensor
Checks
- 1Check the sensor lead and plug
- 2Measure the sensor resistance
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 808Rail pressure sensor error
The rail pressure sensor reading is not plausible. It covers the same part as alarm 608.· Erratic or implausibleErratic or implausibleInfoCauses
- Sensor wiring damaged
- Sensor failed
Checks
- 1Check the sensor supply and signal
- 2Compare the reading with the expected rail pressure
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Thermo King 813General injector error
The engine ECU found a general fault in an injector circuit. Misfire and rough running are possible.· OtherOtherInfoCauses
- Injector wiring damaged
- Injector coil failed
Checks
- 1Check the injector connectors
- 2Measure the injector coil resistance
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 815Fuel pressure regulator error
The regulator that controls fuel pressure in the common rail is not working. The unit may derate or fail to start.· OtherOtherCheck soonCauses
- Regulator wiring damaged
- Regulator stuck
Checks
- 1Check the regulator plug and wiring
- 2Read the commanded and actual rail pressure
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 818EGR valve actuator error
The EGR valve actuator reports an error. Recirculation may be stuck open or closed.· OtherOtherInfoCauses
- Actuator wiring damaged
- Valve stuck with soot
Checks
- 1Check the actuator plug and wiring
- 2Inspect the valve for soot
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 827EGR valve position sensor error
The EGR valve position sensor reports an error. The ECU cannot confirm where the valve is.· OtherOtherInfoCauses
- Sensor wiring fault
- Sensor failed
Checks
- 1Check the sensor plug
- 2Read the valve position with the service tool
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 833High pressure pump fuel metering unit error
The fuel metering unit on the high pressure pump reports an error. Rail pressure cannot be regulated properly.· Real conditionReal conditionInfoCauses
- Metering unit wiring fault
- Dirty fuel in the unit
Checks
- 1Check the metering unit plug and wiring
- 2Check the fuel quality and filters
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Thermo King 840Fuel injection energizing error
The way the ECU energizes the injectors is faulty. The engine may run on fewer cylinders.· OtherOtherInfoCauses
- Injector wiring or coil fault
- ECU driver fault
Checks
- 1Check the injector wiring
- 2Read the injector codes with the service tool
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Thermo King 841High pressure pump wear
The engine ECU believes the high pressure pump is wearing out because it needs unusual control values to build pressure.· Real conditionReal conditionInfoCauses
- Pump wear
- Fuel contamination
Checks
- 1Check fuel quality and filters
- 2Have the pump tested
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Thermo King 843Fuel injection system error
The ECU reports a fuel injection system fault that is not a single injector. Check the fuel supply and injector circuits.· OtherOtherInfoCauses
- Poor fuel quality
- Injector wiring or pump fault
Checks
- 1Check the fuel filter and supply
- 2Read other injection codes with the service tool
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Check the fuel supply, lift pump and filter first for restriction and air
- 2Check the injector plugs for a firm latch and clean contacts
- 3Inspect the valve for soot and free movement
- 4Read the rail pressure with the service tool and compare it with the target
- 5Measure each injector coil resistance and compare them
- 6Check the actuator and sensor plugs for corrosion
- 7Check the sensor and regulator plugs for corrosion and bent pins
Causes
- Air or water in the fuel
- Injector wiring damaged
- Valve stuck with soot
- Rail pressure sensor wiring fault
Most common here: real condition (4 of 16)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: Hard starting, loss of power or an engine stop, with an engine ECU alarm on the display.
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
