EF Logo

Thermo King · Engine ECU faults (SR-2/SR-3/SR-4)

Thermo King Engine ECU air sensors, power, relays and CAN link fault codes

This page covers the engine ECU inputs and links: intake air, pressure and exhaust sensors, ECU power and relays, and the engine CAN data link. The engine ECU reads intake air and exhaust temperatures, intake, atmospheric and exhaust pressures and the air flow.

More about these parts

The engine ECU needs a switched supply through a relay and a stable battery voltage. The controller and the engine ECU communicate over a CAN data link.

FaultInfo508Thermo King · Engine ECU air sensors, power, relays and CAN link
Code shows hereFAULT508

Where this code shows

Press the alarm key or open the Alarms menu on the controller display to list active alarms.

What do these codes mean?

Thermo King codes 508 to 838 are all about the engine ECU air sensors, power, relays and CAN link. The most common failure type is lost message (6 of 21); 1 needs an immediate stop. Start with this check: check the sensor plug and lead for damage and oil.

How urgent are they?

1 of 21 codes here means stop now; 1 can wait until the shift ends, but find the cause before the next one; 19 are information only.

  • Stop now1
  • Check soon1
  • Info19

What should I check first?

Check the sensor plug and lead for damage and oil

Shared checks

21 of 21

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Thermo King 508Speed request communication error

    The speed request the controller sends to the engine ECU did not get through correctly.· Lost message
    Info

    Causes

    • Damaged CAN wiring between controller and ECU
    • Loose ECU connector

    Checks

    1. 1Check the CAN wires and plugs between the controller and the engine ECU
    2. 2Look for related CAN alarms such as 538 or 539
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Thermo King 538Engine J1939 CAN data link degraded

    The J1939 data link between the controller and the engine ECU is working poorly, with lost or corrupted messages.· Lost message
    Check soon

    Causes

    • CAN wiring damaged
    • Terminating resistor fault
    • Connector corrosion

    Checks

    1. 1Check the CAN wiring for chafing and loose pins
    2. 2Measure the CAN bus resistance with power off at the engine connector
    3. 3Inspect the CAN connectors for water, green corrosion and bent pins
    4. 4Read the ECU faults with the engine service tool for related CAN codes
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Thermo King 539Engine J1939 CAN data link failed

    The J1939 data link between the controller and the engine ECU has failed completely, so the controller no longer hears the engine.· Lost message
    Stop now

    Causes

    • CAN wires cut or shorted together
    • ECU not powered
    • Controller CAN port failed

    Checks

    1. 1Check the CAN wires between controller and ECU for cuts
    2. 2Check the ECU power and ground supply with a meter at its connector
    3. 3Inspect the CAN connectors for corrosion and loose, spread pins
    4. 4Replace the ECU or the controller if the link stays dead
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Thermo King 603Exhaust pressure sensor check

    The exhaust pressure sensor signal is out of range, so the ECU loses the back-pressure reading it uses for EGR and boost control.· Other
    Info

    Causes

    • Exhaust pressure sensor wiring damaged by heat
    • Sensing port clogged with soot

    Checks

    1. 1Look at the sensor plug and port near the exhaust for heat damage and soot.
    2. 2Read the exhaust pressure with the service tool at idle and compare it with the other pressure readings.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 605Fresh air temperature sensor check

    The fresh air temperature sensor in the engine air inlet is out of range, so the ECU loses the air temperature it uses to correct fuelling.· Other
    Info

    Causes

    • Fresh air sensor lead open or shorted
    • Sensor failed

    Checks

    1. 1Inspect the fresh air sensor lead and plug at the air inlet.
    2. 2Measure the sensor resistance and compare it with the ambient temperature.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 609Intake pressure sensor check

    The intake manifold pressure sensor is out of range, so the ECU cannot correct fuelling for boost.· Other
    Info

    Causes

    • Intake pressure sensor supply or signal wire damaged
    • Sensor failed

    Checks

    1. 1Check the intake pressure sensor plug and its supply voltage.
    2. 2Read the intake pressure with the service tool with the engine off and then running.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 610Atmospheric pressure sensor check

    The atmospheric pressure sensor is out of range, so altitude corrections to fuelling are lost.· Other
    Info

    Causes

    • Atmospheric sensor wire damaged
    • Sensor failed

    Checks

    1. 1Check the atmospheric sensor plug for corrosion.
    2. 2With the engine off compare the reading with the known local air pressure.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 619ECU main relay fault

    The engine ECU main relay is not behaving correctly, so the ECU may not be powered or may not switch off.· Other
    Info

    Causes

    • Relay contacts sticking
    • Relay socket corroded

    Checks

    1. 1Swap the relay with a known good one
    2. 2Check the relay socket and fuse
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 623TRUCAN message timeout

    The engine ECU stopped receiving an expected message from the unit controller over the TRUCAN data link.· Lost message
    Info

    Causes

    • Intermittent CAN wiring fault
    • Controller reset

    Checks

    1. 1Check the data link wiring and connectors
    2. 2Look for power supply dips at the controller
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Thermo King 625Intake air temperature sensor check

    The intake air temperature sensor is out of range, so the ECU may over or under fuel as the intake air changes temperature.· Other
    Info

    Causes

    • Intake air sensor lead open or shorted
    • Sensor failed

    Checks

    1. 1Inspect the intake air sensor lead and plug.
    2. 2Measure the sensor resistance cold and compare it with ambient.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 626Exhaust temperature sensor check

    The exhaust temperature sensor is out of range, so emission and exhaust protection functions that rely on it may be limited.· Other
    Info

    Causes

    • Exhaust sensor wire burnt or open near the exhaust
    • Sensor failed

    Checks

    1. 1Inspect the exhaust sensor lead near the exhaust pipe for burnt insulation.
    2. 2Measure the sensor resistance and see that it changes with temperature.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 809Intake air pressure sensor error

    The intake air pressure sensor reports an error flag; it is the same sensor as alarm 609 and is cleared the same way.· Other
    Info

    Causes

    • Intake pressure sensor wiring fault
    • Sensor failed

    Checks

    1. 1Check the intake pressure sensor plug and wiring.
    2. 2Read the intake pressure with the service tool and note if it matches 609.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 810Atmospheric pressure sensor error

    The atmospheric pressure sensor reports an error flag; it is the same sensor as alarm 610 and is cleared the same way.· Other
    Info

    Causes

    • Atmospheric sensor wiring fault
    • Sensor failed

    Checks

    1. 1Check the atmospheric sensor plug and wiring.
    2. 2Read the value with the service tool and compare it with local air pressure.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 819ECU power relay error

    The relay that powers the engine ECU shows an error.· Lost message
    Info

    Causes

    • Relay faulty
    • Socket or fuse fault

    Checks

    1. 1Swap the relay with a known good one
    2. 2Check the supply wire to the ECU
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Thermo King 825T1 air intake temperature sensor error

    The T1 intake air temperature sensor reports an error, so the ECU cannot use that sensor to correct fuelling.· Other
    Info

    Causes

    • T1 sensor lead damaged
    • T1 sensor failed

    Checks

    1. 1Check the T1 sensor plug and lead.
    2. 2Compare the T1 resistance with the T2 sensor, if fitted, on the same engine.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 826T2 air intake temperature sensor error

    The T2 intake air temperature sensor reports an error, so the ECU cannot use that sensor to correct fuelling.· Other
    Info

    Causes

    • T2 sensor lead damaged
    • T2 sensor failed

    Checks

    1. 1Check the T2 sensor plug and lead.
    2. 2Compare the T2 resistance with the T1 sensor on the same engine.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 828Lambda system error

    The lambda (oxygen) system reports an error, so exhaust control cannot be verified in the normal way.· Other
    Info

    Causes

    • Lambda sensor wiring fault
    • Lambda sensor failed

    Checks

    1. 1Check the lambda sensor plug and wiring near the exhaust.
    2. 2Read the lambda value with the service tool when the engine is warm.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 829Main ECU relay error

    The main relay of the engine ECU reports an error.· Other
    Info

    Causes

    • Relay failed
    • Wiring fault

    Checks

    1. 1Check the relay and its socket
    2. 2Measure the relay coil supply
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 830Air flow meter error

    The air flow meter on the intake reports an error, so the ECU cannot meter the incoming air correctly.· Other
    Info

    Causes

    • Air flow meter wiring fault
    • Meter element dirty or failed

    Checks

    1. 1Check the air flow meter plug and the air cleaner for a blockage or oil.
    2. 2Read the air flow with the service tool and see whether it follows engine speed.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 832Engine power supply error

    The supply voltage seen by the engine ECU is outside its range.· Lost message
    Info

    Causes

    • Weak battery or loose battery terminal
    • Alternator fault

    Checks

    1. 1Check the battery voltage with the engine off and running
    2. 2Check the battery terminals and earth
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Thermo King 838Intake air system error

    The ECU reports a general intake air system fault, such as a blockage or a leak between the air cleaner and the engine.· Other
    Info

    Causes

    • Air cleaner blocked
    • Leak or split in an intake hose

    Checks

    1. 1Inspect the air cleaner and replace it if clogged.
    2. 2Check the intake hoses and clamps for splits and loose joints, then read the intake pressure.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Check the sensor plug and lead for damage and oil
  2. 2Swap the relay with a known good one of the same type
  3. 3Check the CAN wiring and connectors between controller and engine ECU
  4. 4Measure the sensor resistance or output voltage against the service data
  5. 5Check the battery and its terminals for voltage drop
  6. 6Check the supply voltage at both ends of the link
  7. 7Read the live value with the service tool and compare with the engine state

Causes

  • Sensor wiring damaged
  • Relay failed
  • CAN wires damaged
  • Sensor failed

Most common here: lost message (6 of 21)

Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

When to stop

You'll notice: Power loss, smoke or a sensor alarm on the display, often with no other symptom.

Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.