EF Logo

Thermo King · Maintenance reminders (SR-2/SR-3/SR-4)

Thermo King Run-time reminders and hourmeter limits fault codes

This page covers the service reminders: engine, electric and total run-time reminders and the hourmeter limits. The controller counts engine, electric and total run hours and tells the owner when a service is due.

More about these parts

Extra hourmeters on the controller can be set to remind the owner of a service.

FaultInfo128Thermo King · Run-time reminders and hourmeter limits
Code shows hereFAULT128

Where this code shows

Press the alarm key or open the Alarms menu on the controller display to list active alarms.

What do these codes mean?

Thermo King codes 64 to 134 are all about the run-time reminders and hourmeter limits. The most common failure type is real condition (3 of 12); none needs an immediate stop. Start with this check: do the service that is due for the counter shown on the display.

How urgent are they?

None of the 12 codes here means stop now; 1 can wait until the shift ends, but find the cause before the next one; 11 are information only.

  • Check soon1
  • Info11

What should I check first?

Do the service that is due for the counter shown on the display

Shared checks

12 of 12

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Thermo King 64Pretrip reminder

    A reminder that a pretrip inspection is due based on the elapsed time since the last pretrip was completed.· Other
    Info

    Causes

    • Pretrip interval has expired
    • Pretrip never run since the interval was set
    • Hour meter threshold reached

    Checks

    1. 1Run a pretrip test from the controller menu and watch each step through
    2. 2Clear the alarm after the pretrip completes, so the interval timer restarts
    3. 3Check the interval setting in the configuration
    4. 4Record the date of the pretrip in the maintenance log for the unit
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 70Hourmeter failure

    The controller found an error in one of its hourmeter counters, so run-time records for service intervals may be wrong.· Other
    Check soon

    Causes

    • Memory fault inside the controller
    • Controller reset after power loss
    • Failed controller board

    Checks

    1. 1Open the hourmeter display and compare with the unit service records
    2. 2Clear alarms and watch if the hours count normally
    3. 3Replace the controller if the meter keeps failing
    4. 4Re-enter the hour values if the service tool allows
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 71Hourmeter 4 exceeds set time limit

    Hourmeter 4 has run past the time limit it was set to.· Real condition
    Info

    Causes

    • Maintenance interval reached
    • Hourmeter not reset after service

    Checks

    1. 1Do the service that hourmeter 4 tracks
    2. 2Reset the hourmeter after service
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Thermo King 72Hourmeter 5 exceeds set time limit

    Hourmeter 5 has run past the time limit it was set to.· Real condition
    Info

    Causes

    • Maintenance interval reached
    • Hourmeter not reset after service

    Checks

    1. 1Do the service that hourmeter 5 tracks
    2. 2Reset the hourmeter after service
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Thermo King 73Hourmeter 6 exceeds set time limit

    Hourmeter 6 has run past the time limit it was set to.· Real condition
    Info

    Causes

    • Maintenance interval reached
    • Hourmeter not reset after service

    Checks

    1. 1Do the service that hourmeter 6 tracks
    2. 2Reset the hourmeter after service
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Thermo King 128Engine run time maintenance reminder 1 / service due

    The engine run time has reached the first maintenance interval, so the unit is due for its engine service.· Other
    Info

    Causes

    • Engine hours reached the service interval
    • Hourmeter not reset after the last service
    • Interval set shorter than needed

    Checks

    1. 1Do the engine service: oil, filters and belt inspection per the service schedule
    2. 2Reset the maintenance hourmeter in the menu after the work is complete
    3. 3Check the interval setting is what the fleet intends and was not changed by mistake
    4. 4Record the service in the maintenance log with the hours
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 129Engine run time maintenance reminder 2

    The second engine run-time service reminder has come due.· Other
    Info

    Causes

    • Service interval reached
    • Reminder not reset after the last service

    Checks

    1. 1Do the service listed for reminder 2
    2. 2Reset the reminder in the maintenance menu
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 130Engine run time maintenance reminder 1

    The first engine run-time service reminder has come due.· Other
    Info

    Causes

    • Service interval reached
    • Reminder not reset after the last service

    Checks

    1. 1Do the service listed for reminder 1
    2. 2Reset the reminder in the maintenance menu
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 131Electric run time maintenance reminder 2

    The second electric run-time service reminder has come due.· Other
    Info

    Causes

    • Service interval reached
    • Reminder not reset

    Checks

    1. 1Do the electric standby service
    2. 2Reset the reminder in the maintenance menu
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 132Total unit run time maintenance reminder 1

    The first total unit run-time reminder has come due.· Other
    Info

    Causes

    • Service interval reached
    • Reminder not reset

    Checks

    1. 1Do the service for total run time
    2. 2Reset the reminder in the maintenance menu
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 133Total unit run time maintenance reminder 2

    The second total unit run-time reminder has come due.· Other
    Info

    Causes

    • Service interval reached
    • Reminder not reset

    Checks

    1. 1Do the service for total run time
    2. 2Reset the reminder in the maintenance menu
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Thermo King 134Controller power on hours

    The controller power-on hours have reached a set limit.· Other
    Info

    Causes

    • Set hours reached
    • Reminder not reset

    Checks

    1. 1Do the service linked to the controller hours
    2. 2Reset the reminder after service
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Do the service that is due for the counter shown on the display
  2. 2Do the service tracked by the hourmeter that tripped
  3. 3Reset the reminder in the maintenance menu after the service
  4. 4Reset the hourmeter after the service is finished
  5. 5Check the interval settings in the controller
  6. 6Check the hourmeter limit settings in the controller menu
  7. 7Record the service in the unit log for the next visit

Causes

  • Service interval reached
  • Limit reached
  • Reminder not reset
  • Not reset after service

Most common here: real condition (3 of 12)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: A reminder alarm for the end-of-day report that does not affect running.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.