EF Logo

Cummins fault codes

Cummins engines show their own fault code number, and each one stands for a J1939 SPN and FMI. Read it on the dash or with INSITE, then look it up here by the Cummins number.

831 codes in 42 families24 stop now, 690 check soon, 117 info

831 Cummins codes - type a code, or a word from the problem.

Covers Trucks, Excavators, Loaders, Generators.

Where to look

  1. 01Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
  2. 02Read the active codes first, then the inactive ones, and note the Cummins code number…
  3. 03Open the freeze-frame data to see engine speed, load and temperature at the moment…
  4. 04Work the codes in the order they set, because derate codes such as 3714 or 6255 only…
  5. 05Fix the cause, clear the codes with the tool and road-test under load to confirm they…
How to read Cummins fault codes, in full
  1. Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
  2. Read the active codes first, then the inactive ones, and note the Cummins code number with its SPN and FMI.
  3. Open the freeze-frame data to see engine speed, load and temperature at the moment the code set.
  4. Work the codes in the order they set, because derate codes such as 3714 or 6255 only report a problem found elsewhere.
  5. Fix the cause, clear the codes with the tool and road-test under load to confirm they do not return.

How urgent is a Cummins code?

Stop now24 codes
Shut down and fix before working on. Running on risks damage or the machine locks out.
Check soon690 codes
The machine may derate or limit a function. Find the cause before the next shift.
Information117 codes
A reminder or status message. Nothing is failing yet.

Pick your system

Find the part of the machine, then the family your code belongs to.

Code range
The first and last code in the family, as the machine shows them.
Codes
How many codes the family holds; each is explained on its page.
Severity mix
The share of stop, check and info codes. The dot after it is the most urgent one in the family.

Air handling138 codes

Starting aid17 codes

Cooling37 codes

Fuel system65 codes

Aftertreatment317 codes

Electrical18 codes

Engine control module24 codes

Engine protection4 codes

Operator controls89 codes

Vehicle speed22 codes

Engine speed sensors14 codes

Engine brake10 codes

Most searched Cummins codes

Quick answers

How do I read Cummins fault codes?

Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port. Read the active codes first, then the inactive ones, and note the Cummins code number with its SPN and FMI.

Which Cummins codes mean stop now?

24 of the 831 Cummins codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example 111, 115, 415, 3712. 690 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.

What should I check first on a Cummins code?

Most Cummins codes here (174 of 831) read as erratic or implausible: the reading jumps, drifts or disagrees with the sensors around it. First test, as general workshop practice: watch the live value on the service tool while you flex the harness and tap the connector.

Which Cummins codes are looked up most?

111 (engine control module - critical internal failure), 115 (engine speed/position - both sensor signals lost), 122 (intake manifold pressure sensor signal voltage high), 123 (intake manifold pressure sensor signal voltage low), 131 (accelerator pedal position sensor signal voltage high). Each page gives the meaning, the likely causes and the checks.

Sources

Every code was read from these documents and written in our own words.

Other makers

Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.