Cummins · Fuel system - SPN 157 FMI 4
Cummins Fault Code 452
Fuel rail (injector metering rail) pressure sensor signal voltage low
What does Cummins code 452 mean?
The ECM sees the fuel rail (injector metering rail) pressure sensor signal below its normal voltage band. Urgency: check soon - the machine may derate or limit a function. Check first: read the rail pressure while cranking; a value that stays pinned at zero with a running pump points at the sensor circuit.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read the rail pressure while cranking; a value that stays pinned at zero with a running pump points at the sensor circuit
Then 4 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 5 done
Causes
- Rail pressure sensor signal wire shorted to ground against the head or rail bracket
- 5 V reference open at the rail sensor plug, so the sensor outputs nothing
- Sensor failed low internally
- Connector backed out of the rail sensor, leaving the pins partly connected
How it failed
You'll notice: Expect hard starting, rough running or a limp-home power cut, because the ECM cannot control rail pressure well.
Shorted lowRead from how the source describes the code
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Fuel rail pressure and fuel supply pump
5 other codes on this part are also shorted low (271, 484, 2266, 4263 and more). When they show together, start at the wiring and connector they share.
- 272Engine fuel pump pressurizing assembly 1 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 281Engine fuel pump pressurizing assembly 1 - mechanical fault or not respondingPart or controllerCheck soon
- 449Fuel rail pressure too high - most severeReal conditionStop now
- 451Fuel rail (injector metering rail) pressure sensor signal voltage highShorted highCheck soon
- 452Fuel rail (injector metering rail) pressure sensor signal voltage lowShorted lowCheck soon
- 483Injector metering rail 2 pressure sensor circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 484Injector metering rail 2 pressure sensor circuit - voltage low (shorted to a low source)Shorted lowCheck soon
- 553Injector metering rail 1 pressure - above normal - moderately severeReal conditionCheck soon
- 559Fuel rail pressure low - moderately severeOtherCheck soon
Show the other 15 codesHide the other codes
- 271Fuel pump actuator circuit shorted low or driver voltage lowShorted lowCheck soon
- 755Injector metering rail 1 pressure - mechanical fault or not respondingPart or controllerCheck soon
- 1911Injector metering rail 1 pressure circuit - above normal - most severeReal conditionStop now
- 2265Electric lift pump circuit - voltage highShorted highCheck soon
- 2266Electric fuel lift pump circuit shorted low or driver voltage lowShorted lowCheck soon
- 3727High-pressure common rail fuel pressure relief valve - mechanical fault or not respondingPart or controllerCheck soon
- 3741High pressure common rail fuel pressure relief valve - above normal - most severeReal conditionCheck soon
- 4262High pressure common rail fuel pressure relief valve circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 4263High pressure common rail fuel pressure relief valve circuit - voltage low (shorted to a low source)Shorted lowCheck soon
- 4265High pressure common rail fuel pressure relief valve - root cause not knownReal conditionInformation
- 4691Engine injector metering rail 1 cranking pressure - below normal - moderately severeReal conditionCheck soon
- 4727Injector metering rail 1 pressure - above normal - least severeReal conditionInformation
- 4841Engine injector metering rail 1 cold start pressure - above normal - moderately severeReal conditionCheck soon
- 6258Electric lift pump for engine fuel supply - voltage high (shorted to a high source)Shorted highCheck soon
- 6259Electric lift pump for engine fuel supply - voltage low (shorted to a low source)Shorted lowCheck soon
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 452 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/ISB6.7/B6.7/L9 engines (J1939 SPN 157, FMI 4); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
