EF Logo

Cummins · Fuel system

Cummins Fuel rail pressure and fuel supply pump fault codes

The rail pressure sensor reads the pressure in the injector metering rail that the high-pressure pump builds. The common rail has a pressure relief valve that opens to protect the rail from overpressure.

More about these parts

The high-pressure fuel pump has an electric actuator that meters fuel into the pressure chamber. An electric lift pump supplies fuel from the tank to the high-pressure pump.

FaultCheck451Cummins · Fuel rail pressure and fuel supply pump
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.

What do these codes mean?

Cummins codes 271 to 6259 are all about the fuel rail pressure and fuel supply pump. The most common failure type is real condition (8 of 24); 2 need an immediate stop. Start with this check: check fuel level, filters and supply restriction first; low-side problems are the most common root cause.

How urgent are they?

2 of 24 codes here mean stop now; 20 can wait until the shift ends, but find the cause before the next one; 2 are information only.

  • Stop now2
  • Check soon20
  • Info2

What should I check first?

Check fuel level, filters and supply restriction first; low-side problems are the most common root cause

Shared checks

24 of 24

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Engine fuel pump pressurizing assembly 1 circuit1 code

    • Cummins 272Engine fuel pump pressurizing assembly 1 circuit: Voltage high / shorted high

      The ECM sees the engine fuel pump pressurizing assembly 1 circuit drive circuit with voltage above the expected level.· Shorted high
      Check soon

      Causes

      • Output wire shorted to battery or a switched power feed
      • Open ground or return path on the component
      • Component winding failed or its connector damaged

      Checks

      1. 1Unplug the engine fuel pump pressurizing assembly 1 circuit connector, key on, and measure the output pin to ground; battery voltage with nothing connected points to a short to power
      2. 2Inspect the harness for a rubbed wire or damaged splice touching a power feed
      3. 3Measure the component resistance across its pins to rule out an open winding
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Engine fuel pump pressurizing assembly 1 circuit - voltage high (shorted to a high source)

  • Engine fuel pump pressurizing assembly 11 code

    • Cummins 281Engine fuel pump pressurizing assembly 1: Mechanical fault or not responding

      The ECM commands the engine fuel pump pressurizing assembly 1 but it does not respond as expected, or its movement is out of adjustment.· Part or controller
      Check soon

      Causes

      • Mechanism seized, sooted or blocked
      • Wear or incorrect adjustment of the linkage or part
      • Supply or return fault limiting its movement

      Checks

      1. 1Command the engine fuel pump pressurizing assembly 1 in INSITE and watch whether it moves and returns
      2. 2Inspect the part and its linkage for sticking, debris or wear
      3. 3Check supply and return connections before replacing it
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Injector metering rail 2 pressure sensor circuit2 codes

    • Cummins 483Injector metering rail 2 pressure sensor circuit: Voltage high / shorted high

      The ECM sees the injector metering rail 2 pressure sensor signal circuit above its normal voltage band.· Shorted high
      Check soon

      Causes

      • Signal wire shorted to the 5 V reference or battery voltage in the harness
      • Open sensor return wire letting the signal float up
      • Sensor failed high or its connector is corroded

      Checks

      1. 1Read the live injector metering rail 2 pressure sensor circuit value with the key on; a reading pinned at the top of its range confirms the high-voltage fault
      2. 2Unplug the sensor and check reference and return at the harness, since a lost return gives the same symptom
      3. 3With the key off, test the signal wire for continuity to the reference and to battery positive
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Injector metering rail 2 pressure sensor circuit - voltage high (shorted to a high source)

    • Cummins 484Injector metering rail 2 pressure sensor circuit: Voltage low / shorted low

      The ECM sees the injector metering rail 2 pressure sensor signal circuit below its normal voltage band.· Shorted low
      Check soon

      Causes

      • Signal wire shorted to ground in the harness
      • Open 5 V reference wire so the signal collapses
      • Sensor failed low or its connector is wet or corroded

      Checks

      1. 1Read the live injector metering rail 2 pressure sensor circuit value with the key on; a reading pinned at the bottom of its range confirms the low-voltage fault
      2. 2Unplug the sensor and check that the 5 V reference arrives at the connector
      3. 3With the key off, test the signal wire for a short to ground
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Injector metering rail 2 pressure sensor circuit - voltage low (shorted to a low source)

  • Injector metering rail 1 pressure3 codes

    • Cummins 553Injector metering rail 1 pressure: Above normal· moderately severe

      The injector metering rail 1 pressure is above its normal operating range and the ECM rates it as moderately severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too high because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live injector metering rail 1 pressure with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Injector metering rail 1 pressure - above normal - moderately severe

    • Cummins 755Injector metering rail 1 pressure: Mechanical fault or not responding

      The ECM commands the injector metering rail 1 pressure but it does not respond as expected, or its movement is out of adjustment.· Part or controller
      Check soon

      Causes

      • Mechanism seized, sooted or blocked
      • Wear or incorrect adjustment of the linkage or part
      • Supply or return fault limiting its movement

      Checks

      1. 1Command the injector metering rail 1 pressure in INSITE and watch whether it moves and returns
      2. 2Inspect the part and its linkage for sticking, debris or wear
      3. 3Check supply and return connections before replacing it
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 4727Injector metering rail 1 pressure: Above normal· least severe

      The injector metering rail 1 pressure is above its normal operating range and the ECM rates it as least severe.· Real condition
      Info

      Causes

      • The monitored condition really is too high because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live injector metering rail 1 pressure with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Injector metering rail 1 pressure - above normal - least severe

  • Injector metering rail 1 pressure circuit1 code

    • Cummins 1911Injector metering rail 1 pressure circuit: Above normal· most severe

      The injector metering rail 1 pressure circuit is above its normal operating range and the ECM rates it as most severe.· Real condition
      Stop now

      Causes

      • The monitored condition really is too high because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live injector metering rail 1 pressure circuit with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Injector metering rail 1 pressure circuit - above normal - most severe

  • Electric lift pump circuit1 code

    • Cummins 2265Electric lift pump circuit: Voltage high

      The ECM sees the electric lift pump driver high, which suggests a short to supply or an open return at the pump.· Shorted high
      Check soon

      Causes

      • Pump driver wire shorted to a supply wire
      • Open return at the pump
      • Pump relay stuck closed

      Checks

      1. 1Key off: check whether the pump still runs or the relay stays closed
      2. 2Pull the lift pump relay and check that its contacts are not stuck closed
      3. 3Measure the driver wire at the pump with the key on
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

  • High-pressure common rail fuel pressure relief valve1 code

    • Cummins 3727High-pressure common rail fuel pressure relief valve: Mechanical fault or not responding

      The ECM commands the high-pressure common rail fuel pressure relief valve but it does not respond as expected, or its movement is out of adjustment.· Part or controller
      Check soon

      Causes

      • Mechanism seized, sooted or blocked
      • Wear or incorrect adjustment of the linkage or part
      • Supply or return fault limiting its movement

      Checks

      1. 1Command the high-pressure common rail fuel pressure relief valve in INSITE and watch whether it moves and returns
      2. 2Inspect the part and its linkage for sticking, debris or wear
      3. 3Check supply and return connections before replacing it
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • High pressure common rail fuel pressure relief valve2 codes

    • Cummins 3741High pressure common rail fuel pressure relief valve: Above normal· most severe

      The high pressure common rail fuel pressure relief valve is above its normal operating range and the ECM rates it as most severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too high because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live high pressure common rail fuel pressure relief valve with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:High pressure common rail fuel pressure relief valve - above normal - most severe

    • Cummins 4265High pressure common rail fuel pressure relief valve: Root cause not known

      The ECM detects a problem with the high pressure common rail fuel pressure relief valve but cannot tie it to one specific cause.· Real condition
      Info

      Causes

      • A related fault that set first
      • An intermittent connection or supply problem

      Checks

      1. 1Read all active and inactive codes and work the others first
      2. 2Check the supply, ground and connectors of the circuit involved
      3. 3Read the freeze-frame data for the conditions when it set
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • High pressure common rail fuel pressure relief valve circuit2 codes

    • Cummins 4262High pressure common rail fuel pressure relief valve circuit: Voltage high / shorted high

      The ECM sees the high pressure common rail fuel pressure relief valve circuit drive circuit with voltage above the expected level.· Shorted high
      Check soon

      Causes

      • Output wire shorted to battery or a switched power feed
      • Open ground or return path on the component
      • Component winding failed or its connector damaged

      Checks

      1. 1Unplug the high pressure common rail fuel pressure relief valve circuit connector, key on, and measure the output pin to ground; battery voltage with nothing connected points to a short to power
      2. 2Inspect the harness for a rubbed wire or damaged splice touching a power feed
      3. 3Measure the component resistance across its pins to rule out an open winding
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:High pressure common rail fuel pressure relief valve circuit - voltage high (shorted to a high source)

    • Cummins 4263High pressure common rail fuel pressure relief valve circuit: Voltage low / shorted low

      The ECM sees the high pressure common rail fuel pressure relief valve circuit drive circuit with voltage below the expected level.· Shorted low
      Check soon

      Causes

      • Output wire shorted to ground or chafed through to the chassis
      • Component winding shorted internally
      • Connector corroded and bridging the pins

      Checks

      1. 1Unplug the high pressure common rail fuel pressure relief valve circuit connector and measure the output pin to ground; a short here means the harness is at fault
      2. 2Measure the component resistance across its pins; a very low reading means a shorted winding
      3. 3Inspect the connector for moisture and bridged terminals
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:High pressure common rail fuel pressure relief valve circuit - voltage low (shorted to a low source)

  • Engine injector metering rail 1 cranking pressure1 code

    • Cummins 4691Engine injector metering rail 1 cranking pressure: Below normal· moderately severe

      The engine injector metering rail 1 cranking pressure is below its normal operating range and the ECM rates it as moderately severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too low because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live engine injector metering rail 1 cranking pressure with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Engine injector metering rail 1 cranking pressure - below normal - moderately severe

  • Engine injector metering rail 1 cold start pressure1 code

    • Cummins 4841Engine injector metering rail 1 cold start pressure: Above normal· moderately severe

      The engine injector metering rail 1 cold start pressure is above its normal operating range and the ECM rates it as moderately severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too high because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live engine injector metering rail 1 cold start pressure with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Engine injector metering rail 1 cold start pressure - above normal - moderately severe

  • Electric lift pump for engine fuel supply2 codes

    • Cummins 6258Electric lift pump for engine fuel supply: Voltage high / shorted high

      The ECM sees the electric lift pump for engine fuel supply drive circuit with voltage above the expected level.· Shorted high
      Check soon

      Causes

      • Output wire shorted to battery or a switched power feed
      • Open ground or return path on the component
      • Component winding failed or its connector damaged

      Checks

      1. 1Unplug the electric lift pump for engine fuel supply connector, key on, and measure the output pin to ground; battery voltage with nothing connected points to a short to power
      2. 2Inspect the harness for a rubbed wire or damaged splice touching a power feed
      3. 3Measure the component resistance across its pins to rule out an open winding
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Electric lift pump for engine fuel supply - voltage high (shorted to a high source)

    • Cummins 6259Electric lift pump for engine fuel supply: Voltage low / shorted low

      The ECM sees the electric lift pump for engine fuel supply drive circuit with voltage below the expected level.· Shorted low
      Check soon

      Causes

      • Output wire shorted to ground or chafed through to the chassis
      • Component winding shorted internally
      • Connector corroded and bridging the pins

      Checks

      1. 1Unplug the electric lift pump for engine fuel supply connector and measure the output pin to ground; a short here means the harness is at fault
      2. 2Measure the component resistance across its pins; a very low reading means a shorted winding
      3. 3Inspect the connector for moisture and bridged terminals
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Electric lift pump for engine fuel supply - voltage low (shorted to a low source)

  • Other codes6 codes

    • Cummins 271Fuel pump actuator circuit shorted low or driver voltage low

      The ECM drives the fuel pump actuator circuit but sees its output pulled to ground.· Shorted low
      Check soon

      Causes

      • Fuel pump metering valve wire shorted to ground
      • Metering valve coil shorted
      • Connector fuel-soaked

      Checks

      1. 1Unplug the actuator and see whether the code becomes an open circuit code
      2. 2Measure the fuel metering actuator coil resistance at the pump connector against the service value
      3. 3Ohm the actuator driver wire to engine ground with the ECM plug removed to find a short
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

    • Cummins 449Fuel rail pressure too high· most severe

      The metering rail pressure is above the highest limit.· Real condition
      Stop now

      Causes

      • Fuel rail pressure sensor reading high
      • Fuel pump or pressure control valve stuck
      • High pressure relief valve not opening

      Checks

      1. 1Read the actual and commanded rail pressure in INSITE
      2. 2Check the rail pressure sensor and its connector for fuel leakage and loose pins
      3. 3Check the pressure control valve and the circuit
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Fuel rail pressure too high - most severe

    • Cummins 451Fuel rail (injector metering rail) pressure sensor signal voltage high

      The ECM sees the fuel rail (injector metering rail) pressure sensor signal above its normal voltage band.· Shorted high
      Check soon

      Causes

      • Rail pressure sensor signal wire shorted to the reference line at the rail connector
      • Return wire open at the rail sensor plug, so the signal floats high
      • Sensor failed high, often after a fuel leak into its connector
      • Water or fuel in the connector bridging reference and signal

      Checks

      1. 1Read the rail pressure with the key on, engine off; it should be near zero, so a high reading confirms a sensor signal fault
      2. 2Unplug the rail sensor and measure the reference and return at the harness before anything else
      3. 3Probe the signal wire to the reference wire with the ECM unplugged to find a hidden short
      4. 4Check the return wire resistance from the sensor to the ECM pin
      5. 5Fit a new rail sensor only after the harness checks and the connector is dry
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

    • Cummins 452Fuel rail (injector metering rail) pressure sensor signal voltage low

      The ECM sees the fuel rail (injector metering rail) pressure sensor signal below its normal voltage band.· Shorted low
      Check soon

      Causes

      • Rail pressure sensor signal wire shorted to ground against the head or rail bracket
      • 5 V reference open at the rail sensor plug, so the sensor outputs nothing
      • Sensor failed low internally
      • Connector backed out of the rail sensor, leaving the pins partly connected

      Checks

      1. 1Read the rail pressure while cranking; a value that stays pinned at zero with a running pump points at the sensor circuit
      2. 2Measure 5 V at the harness reference pin with the sensor unplugged
      3. 3Ohm the signal wire to ground with the ECM connector unplugged to find a short
      4. 4Pull the sensor plug and look for fuel in the connector or a bent pin
      5. 5Replace the sensor if the supply and signal wires are good
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

    • Cummins 559Fuel rail pressure low· moderately severe

      The rail pressure is below what the ECM requested.· Other
      Check soon

      Causes

      • Fuel filter blocked
      • Air in the fuel or a suction leak
      • Fuel transfer pump weak
      • High pressure pump worn or leaking injector
      • Rail pressure sensor reading low

      Checks

      1. 1Check the fuel level and the fuel filter condition
      2. 2Look for air in the fuel and fuel leaks in the supply line
      3. 3Check the fuel transfer pump pressure at the filter head with a gauge to prove the supply is adequate
      4. 4Read actual and commanded rail pressure while cranking
      5. 5Check for leaking injectors and the return line
      6. 6Check the rail pressure sensor reading at key on, engine off for a plausible near-zero value
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

      Source wording:Fuel rail pressure low - moderately severe

      Full page for 559
    • Cummins 2266Electric fuel lift pump circuit shorted low or driver voltage low

      The ECM drives the electric fuel lift pump circuit but sees its output pulled to ground.· Shorted low
      Check soon

      Causes

      • Lift pump driver wire shorted to ground
      • Pump motor shorted
      • Pump relay stuck

      Checks

      1. 1Turn the key on and listen for the lift pump to run for a few seconds as it primes
      2. 2Check the lift pump fuse and relay for burnt contacts and a good supply
      3. 3Measure the supply voltage at the lift pump connector while it is commanded on
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Check fuel level, filters and supply restriction first; low-side problems are the most common root cause
  2. 2Compare rail pressure behaviour with the valve commanded closed in INSITE
  3. 3Measure the actuator coil resistance and test the harness for shorts
  4. 4Check the lift pump fuse and relay first, since they are the cheapest cause
  5. 5Read actual and desired rail pressure in INSITE while cranking and under load to see where they diverge
  6. 6Measure the valve circuit resistance and test the harness for shorts to ground and battery
  7. 7Check low-side fuel pressure and filter condition

Causes

  • Air or restriction in the low-pressure supply to the pump
  • Valve leaking or stuck open
  • Open or shorted actuator circuit
  • Open or shorted pump circuit

Most common here: real condition (8 of 24)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: Hard starting, misfire, low power or a stall.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.