EF Logo

Cummins · Fuel system

Cummins Fuel filter, water in fuel and fuel quantity monitors fault codes

A differential pressure sensor across the fuel filter tells the ECM how restricted the filter is. A sensor in the fuel filter or water separator detects water in the fuel.

More about these parts

These are monitor codes from the injection system. The ECM boosts battery voltage to fire the injectors.

FaultStop351Cummins · Injector power supply
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.

What do these codes mean?

Cummins codes 351 to 4726 are all about the fuel filter, water in fuel and fuel quantity monitors. The most common failure type is real condition (5 of 15); 1 needs an immediate stop. Start with this check: replace the fuel filter at the service interval, then clear the code and retest.

How urgent are they?

1 of 15 codes here means stop now; 12 can wait until the shift ends, but find the cause before the next one; 2 are information only.

  • Stop now1
  • Check soon12
  • Info2

What should I check first?

Replace the fuel filter at the service interval, then clear the code and retest

Shared checks

15 of 15

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Injector power supply1 code

    • Cummins 351Injector power supply: Internal failure

      The ECM's internal injector power supply (the circuit that charges the injector solenoids) has failed.· Other
      Stop now

      Causes

      • Injector supply stage inside the ECM failed
      • Short in an injector harness loading the supply
      • Poor battery or ground feed to the ECM

      Checks

      1. 1Read the active codes; if injector circuit codes are also present, deal with those first
      2. 2Check battery and ground voltage at the ECM during cranking
      3. 3Unplug one injector at a time and see whether the code clears to isolate a shorted injector
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Water in fuel sensor circuit1 code

    • Cummins 428Water in fuel sensor circuit: Voltage high

      The water-in-fuel sensor circuit reads high, which can mean open wiring or a failed sensor.· Shorted high
      Check soon

      Causes

      • Open sensor ground
      • Sensor failed
      • Connector loose

      Checks

      1. 1Check the water-in-fuel sensor connector for loose or corroded pins
      2. 2Check the ground and the signal wire of the sensor for continuity
      3. 3Check the sensor reading with the filter bowl drained
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

  • Water-in-fuel indicator sensor circuit3 codes

    • Cummins 429Water-in-fuel indicator sensor circuit: Voltage low / shorted low

      The ECM sees the water-in-fuel indicator sensor signal circuit below its normal voltage band.· Shorted low
      Check soon

      Causes

      • Signal wire shorted to ground in the harness
      • Open 5 V reference wire so the signal collapses
      • Sensor failed low or its connector is wet or corroded

      Checks

      1. 1Read the live water-in-fuel indicator sensor circuit value with the key on; a reading pinned at the bottom of its range confirms the low-voltage fault
      2. 2Unplug the sensor and check that the 5 V reference arrives at the connector
      3. 3With the key off, test the signal wire for a short to ground
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Water-in-fuel indicator sensor circuit - voltage low (shorted to a low source)

    • Cummins 1845Water-in-fuel indicator sensor circuit: Voltage high / shorted high

      The ECM sees the water-in-fuel indicator sensor signal circuit above its normal voltage band.· Shorted high
      Check soon

      Causes

      • Signal wire shorted to the 5 V reference or battery voltage in the harness
      • Open sensor return wire letting the signal float up
      • Sensor failed high or its connector is corroded

      Checks

      1. 1Read the live water-in-fuel indicator sensor circuit value with the key on; a reading pinned at the top of its range confirms the high-voltage fault
      2. 2Unplug the sensor and check reference and return at the harness, since a lost return gives the same symptom
      3. 3With the key off, test the signal wire for continuity to the reference and to battery positive
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Water-in-fuel indicator sensor circuit - voltage high (shorted to a high source)

    • Cummins 1846Water-in-fuel indicator sensor circuit: Voltage low / shorted low

      The ECM sees the water-in-fuel indicator sensor signal circuit below its normal voltage band.· Shorted low
      Check soon

      Causes

      • Signal wire shorted to ground in the harness
      • Open 5 V reference wire so the signal collapses
      • Sensor failed low or its connector is wet or corroded

      Checks

      1. 1Read the live water-in-fuel indicator sensor circuit value with the key on; a reading pinned at the bottom of its range confirms the low-voltage fault
      2. 2Unplug the sensor and check that the 5 V reference arrives at the connector
      3. 3With the key off, test the signal wire for a short to ground
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Water-in-fuel indicator sensor circuit - voltage low (shorted to a low source)

  • Water-in-fuel indicator1 code

    • Cummins 1852Water-in-fuel indicator: Above normal· moderately severe

      The water-in-fuel indicator is above its normal operating range and the ECM rates it as moderately severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too high because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live water-in-fuel indicator with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Water-in-fuel indicator - above normal - moderately severe

  • Fuel filter differential pressure1 code

    • Cummins 2372Fuel filter differential pressure: Above normal· moderately severe

      The fuel filter differential pressure is above its normal operating range and the ECM rates it as moderately severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too high because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live fuel filter differential pressure with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Fuel filter differential pressure - above normal - moderately severe

  • Engine injector bank 1 barcodes1 code

    • Cummins 2765Engine injector bank 1 barcodes: Out of calibration

      The ECM reports the engine injector bank 1 barcodes as out of calibration, so its value does not agree with the stored calibration or with the other data it is compared against.· Part or controller
      Check soon

      Causes

      • Sensor or device out of tolerance
      • Wrong calibration or learn data after a repair

      Checks

      1. 1Check whether a learn or calibration procedure is needed after the last repair
      2. 2Compare with a related sensor and replace the part if the offset is real
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Engine idle fuel quantity1 code

    • Cummins 3338Engine idle fuel quantity: Below normal· moderately severe

      The engine idle fuel quantity is below its normal operating range and the ECM rates it as moderately severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too low because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live engine idle fuel quantity with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Engine idle fuel quantity - below normal - moderately severe

  • Desired engine fueling state1 code

    • Cummins 4284Desired engine fueling state: Abnormal update rate

      The ECM is not receiving fresh data for the desired engine fueling state at the expected rate.· Lost message
      Check soon

      Causes

      • Data link wiring fault or a poor connector contact
      • The module that sends the message is offline or failing
      • Power or ground problem at the sending module

      Checks

      1. 1Look for other modules reporting timeouts to find where the link is broken
      2. 2Check the data link wiring, connectors and terminators
      3. 3Read the sending module for its own codes
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Engine fuel injection quantity error for multiple cylinders1 code

    • Cummins 4713Engine fuel injection quantity error for multiple cylinders: Condition exists

      The ECM sets this code when it recognises a defined condition for the engine fuel injection quantity error for multiple cylinders.· Other
      Info

      Causes

      • A monitor or protection condition that has been met
      • A related fault that set first

      Checks

      1. 1Read the code description and freeze-frame in INSITE for the exact condition
      2. 2Work the related active codes first, then recheck
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Engine fuel leakage1 code

    • Cummins 4726Engine fuel leakage: Above normal· moderately severe

      The engine fuel leakage is above its normal operating range and the ECM rates it as moderately severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too high because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live engine fuel leakage with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Engine fuel leakage - above normal - moderately severe

  • Other codes3 codes

    • Cummins 418Water in fuel detected· least severe

      The water-in-fuel sensor reports water in the fuel filter or separator.· Lost message
      Check soon

      Causes

      • Water collected in the filter bowl
      • Contaminated fuel
      • Water sensor reading wrong

      Checks

      1. 1Drain the water from the filter or water separator until clean fuel runs out
      2. 2Check the fuel tank for water, which often enters through condensation or a poor cap seal
      3. 3Replace the fuel filter if it is contaminated
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

      Source wording:Water in fuel detected - least severe

    • Cummins 2311Electronic fuel injection control valve circuit

      The ECM has found a problem in the fuel control valve circuit.· Other
      Check soon

      Causes

      • Fuel control valve coil failed
      • Harness fault at the fuel pump
      • Connector contamination

      Checks

      1. 1Check the valve connector for fuel and damage
      2. 2Measure the valve coil resistance against the service value
      3. 3Check the wiring between the fuel control valve and the ECM for chafing and open circuit
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

    • Cummins 2343Fuel filter differential pressure high· least severe

      The pressure drop across the fuel filter is above the first limit, which means the filter is getting restricted.· Real condition
      Info

      Causes

      • Fuel filter blocked by dirt or wax
      • Fuel contamination
      • Sensor reading high

      Checks

      1. 1Replace the fuel filter and check the old filter for contamination
      2. 2Check the fuel quality and the tank for contamination that blocks the filter
      3. 3Check the filter differential pressure sensor connector for damage
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Fuel filter differential pressure high - least severe

Shared checks

Checks, in order

  1. 1Replace the fuel filter at the service interval, then clear the code and retest
  2. 2Drain the water separator and check what comes out; clean fuel should follow the water
  3. 3Inspect the high-pressure fuel system for leaks and look for fuel in the oil
  4. 4Check battery voltage and the ECM power and ground connections under load
  5. 5Check the sensor connector and wiring for corrosion and loose terminals
  6. 6Inspect the sensor connector and wiring for corrosion and loose terminals
  7. 7Check low-side fuel pressure and look for air in the fuel

Causes

  • Filter plugged by contamination or wax
  • Water collected in the filter or separator
  • Injector or fuel line leak
  • ECM injector driver supply failed

Most common here: real condition (5 of 15)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: Reduced power under load and a service warning as the filter clogs.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.