EF Logo

Cummins · Air handling

Cummins Turbocharger speed and compressor inlet sensors fault codes

A speed sensor reads the turbine shaft rotation so the ECM can protect the turbo from overspeed and control boost. Sensors at the compressor inlet measure air pressure and temperature before the turbo, which lets the ECM correct boost and protect the turbo from surge or overheating.

More about these parts

The ECM calculates compressor outlet and turbine inlet temperature from other sensor readings rather than measuring them directly, and sets a fault when the calculated value gets too high.

FaultCheck595Cummins · Turbocharger 1 speed
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.

What do these codes mean?

Cummins codes 595 to 7861 are all about the turbocharger speed and compressor inlet sensors. The most common failure type is real condition (8 of 17); none needs an immediate stop. Start with this check: check the turbo shaft for play and the compressor wheel for damage before anything else.

How urgent are they?

None of the 17 codes here means stop now; 14 can wait until the shift ends, but find the cause before the next one; 3 are information only.

  • Check soon14
  • Info3

What should I check first?

Check the turbo shaft for play and the compressor wheel for damage before anything else

Shared checks

17 of 17

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Turbocharger 1 speed4 codes

    • Cummins 595Turbocharger 1 speed: Above normal· moderately severe

      Same failure as 2288 on the turbocharger 1 speed: the same fault condition as 2288, reported for this part.· Real condition
      Check soon

      Causes

      • Same causes as 2288, applied to the turbocharger 1 speed
      • Wiring or connector problem local to the turbocharger 1 speed

      Checks

      1. 1Inspect the speed sensor tip for contact with the compressor wheel nut and for oil or debris.
      2. 2Work through the checks listed for 2288, starting at the turbocharger 1 speed and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Turbocharger 1 speed - above normal - moderately severe

    • Cummins 686Turbocharger 1 speed: Erratic reading

      The ECM judges the turbocharger 1 speed to be erratic or implausible: the value jumps, drifts or disagrees with related readings, which suggests a poor connection or a part on its way out.· Erratic or implausible
      Check soon

      Causes

      • Intermittent connector or wiring contact on the turbocharger 1 speed
      • Part ageing or failing and giving unstable output
      • Electrical noise from a poorly routed wire or a bad ground

      Checks

      1. 1Watch the turbocharger 1 speed live in INSITE and wiggle the harness and connector to catch dropouts
      2. 2Compare the turbocharger 1 speed with a related reading to decide which one is wrong
      3. 3Check the connector for moisture and corrosion and the ground connection for tightness
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:Turbocharger 1 speed - data erratic or incorrect

    • Cummins 687Turbocharger 1 speed: Below normal· moderately severe

      The turbocharger 1 speed is below its normal range (severity: moderately severe).· Real condition
      Check soon

      Causes

      • A real shortfall in the system the turbocharger 1 speed measures
      • Sensor or circuit reading low from a wiring fault
      • A leak, low level or weak supply that lets the value fall

      Checks

      1. 1Confirm the real condition with a gauge or a second reading before replacing the turbocharger 1 speed
      2. 2Check that the turbocharger 1 speed circuit codes are not active, since a wiring fault can fake a low reading
      3. 3Look for the physical cause upstream, such as a leak, low fluid, weak pump or blocked supply
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Turbocharger 1 speed - below normal - moderately severe

    • Cummins 2288Turbocharger 1 speed: Above normal· least severe

      The turbocharger 1 speed is above its normal range (severity: least severe).· Real condition
      Info

      Causes

      • A real over-limit condition in the system the turbocharger 1 speed measures
      • Sensor or circuit reading high from a wiring fault
      • A cooling, flow or restriction problem upstream that drives the value up

      Checks

      1. 1Confirm the real condition with a gauge or a second reading before replacing the turbocharger 1 speed
      2. 2Check that the turbocharger 1 speed circuit codes are not active, since a wiring fault can fake a high reading
      3. 3Look for the physical cause upstream, such as restriction, leakage, poor cooling or heavy load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Turbocharger 1 speed - above normal - least severe

  • Turbocharger 1 compressor inlet pressure1 code

    • Cummins 629Turbocharger 1 compressor inlet pressure: Below normal· moderately severe

      Same failure as 687 on the turbocharger 1 compressor inlet pressure: the same fault condition as 687, reported for this part.· Real condition
      Check soon

      Causes

      • Same causes as 687, applied to the turbocharger 1 compressor inlet pressure
      • Wiring or connector problem local to the turbocharger 1 compressor inlet pressure

      Checks

      1. 1Check the air filter restriction and the intake piping for collapse or blockage.
      2. 2Work through the checks listed for 687, starting at the turbocharger 1 compressor inlet pressure and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Turbocharger 1 compressor inlet pressure - below normal - moderately severe

  • Turbocharger 1 compressor intake temperature sensor circuit1 code

    • Cummins 691Turbocharger 1 compressor intake temperature sensor circuit: Voltage high / shorted high

      The ECM reads the turbocharger 1 compressor intake temperature sensor circuit above its allowed voltage band.· Shorted high
      Check soon

      Causes

      • Short to a 5 V reference or a battery wire in the harness to the turbocharger 1 compressor intake temperature sensor circuit
      • Open or high-resistance return wire that lets the signal float high
      • Water or corrosion in the connector bridging two pins together

      Checks

      1. 1Key on, unplug the turbocharger 1 compressor intake temperature sensor circuit and read its circuit at the harness: a high reading with the part removed means the wiring is shorted high or the return is lost
      2. 2Jumper the signal wire of the turbocharger 1 compressor intake temperature sensor circuit to ground at the harness and see whether the code changes to a low-voltage code, which proves the wiring and the ECM input
      3. 3Check continuity and resistance of the return wire from the turbocharger 1 compressor intake temperature sensor circuit back to the ECM
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Turbocharger 1 compressor intake temperature sensor circuit - voltage high (shorted to a high source)

  • Turbocharger 1 compressor intake temperature circuit1 code

    • Cummins 692Turbocharger 1 compressor intake temperature circuit: Voltage low / shorted low

      The ECM reads the turbocharger 1 compressor intake temperature circuit below its allowed voltage band.· Shorted low
      Check soon

      Causes

      • Signal wire to the turbocharger 1 compressor intake temperature circuit rubbed through and shorted to ground or to the engine block
      • Open 5 V reference or open signal wire that lets the input drop to zero
      • Corroded or backed-out pin in the turbocharger 1 compressor intake temperature circuit connector

      Checks

      1. 1Key on, unplug the turbocharger 1 compressor intake temperature circuit and read its circuit at the harness: a reading near zero with the part removed means the wiring is shorted to ground or open
      2. 2Jumper the 5 V reference to the signal wire at the harness and see whether the code changes to a high-voltage code, which proves the wiring and the ECM input
      3. 3Measure resistance from the turbocharger 1 compressor intake temperature circuit signal wire to ground with the ECM unplugged to find a short
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Turbocharger 1 compressor intake temperature circuit - voltage low (shorted to a low source)

  • Turbocharger 1 compressor intake temperature1 code

    • Cummins 693Turbocharger 1 compressor intake temperature: Erratic reading

      Same failure as 686 on the turbocharger 1 compressor intake temperature: the same fault condition as 686, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 686, applied to the turbocharger 1 compressor intake temperature
      • Wiring or connector problem local to the turbocharger 1 compressor intake temperature

      Checks

      1. 1Check the sensor is clear of the air filter housing connector and the intake piping is not leaking.
      2. 2Work through the checks listed for 686, starting at the turbocharger 1 compressor intake temperature and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:Turbocharger 1 compressor intake temperature - data erratic or incorrect

  • Turbocharger 1 compressor intake pressure circuit2 codes

    • Cummins 741Turbocharger 1 compressor intake pressure circuit: Voltage high / shorted high

      Same failure as 691 on the turbocharger 1 compressor intake pressure circuit: the same fault condition as 691, reported for this part.· Shorted high
      Check soon

      Causes

      • Same causes as 691, applied to the turbocharger 1 compressor intake pressure circuit
      • Wiring or connector problem local to the turbocharger 1 compressor intake pressure circuit

      Checks

      1. 1Check the air filter restriction and the intake piping for collapse or blockage.
      2. 2Work through the checks listed for 691, starting at the turbocharger 1 compressor intake pressure circuit and its connector
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Turbocharger 1 compressor intake pressure circuit - voltage high (shorted to a high source)

    • Cummins 742Turbocharger 1 compressor intake pressure circuit: Voltage low / shorted low

      Same failure as 692 on the turbocharger 1 compressor intake pressure circuit: the same fault condition as 692, reported for this part.· Shorted low
      Check soon

      Causes

      • Same causes as 692, applied to the turbocharger 1 compressor intake pressure circuit
      • Wiring or connector problem local to the turbocharger 1 compressor intake pressure circuit

      Checks

      1. 1Check the air filter restriction and the intake piping for collapse or blockage.
      2. 2Work through the checks listed for 692, starting at the turbocharger 1 compressor intake pressure circuit and its connector
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Turbocharger 1 compressor intake pressure circuit - voltage low (shorted to a low source)

  • Turbocharger 1 compressor intake pressure2 codes

    • Cummins 743Turbocharger 1 compressor intake pressure: Erratic reading

      Same failure as 686 on the turbocharger 1 compressor intake pressure: the same fault condition as 686, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 686, applied to the turbocharger 1 compressor intake pressure
      • Wiring or connector problem local to the turbocharger 1 compressor intake pressure

      Checks

      1. 1Check the air filter restriction and the intake piping for collapse or blockage.
      2. 2Work through the checks listed for 686, starting at the turbocharger 1 compressor intake pressure and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:Turbocharger 1 compressor intake pressure - data erratic or incorrect

    • Cummins 3348Turbocharger 1 compressor intake pressure: Below normal· most severe

      Same failure as 687 on the turbocharger 1 compressor intake pressure: the same fault condition as 687, reported for this part.· Real condition
      Check soon

      Causes

      • Same causes as 687, applied to the turbocharger 1 compressor intake pressure
      • Wiring or connector problem local to the turbocharger 1 compressor intake pressure

      Checks

      1. 1Check the air filter restriction and the intake piping for collapse or blockage.
      2. 2Work through the checks listed for 687, starting at the turbocharger 1 compressor intake pressure and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Turbocharger 1 compressor intake pressure - below normal - most severe

  • Turbocharger turbine intake temperature2 codes

    • Cummins 2346Turbocharger turbine intake temperature: Above normal· least severe

      Same failure as 2288 on the turbocharger turbine intake temperature: the same fault condition as 2288, reported for this part.· Real condition
      Info

      Causes

      • Same causes as 2288, applied to the turbocharger turbine intake temperature
      • Wiring or connector problem local to the turbocharger turbine intake temperature

      Checks

      1. 1Look for a real cause of high exhaust heat, such as an overloaded engine or an air supply restriction.
      2. 2Work through the checks listed for 2288, starting at the turbocharger turbine intake temperature and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Turbocharger turbine intake temperature - above normal - least severe

    • Cummins 2451Turbocharger turbine intake temperature: Above normal· moderately severe

      Same failure as 2288 on the turbocharger turbine intake temperature: the same fault condition as 2288, reported for this part.· Real condition
      Check soon

      Causes

      • Same causes as 2288, applied to the turbocharger turbine intake temperature
      • Wiring or connector problem local to the turbocharger turbine intake temperature

      Checks

      1. 1Look for a real cause of high exhaust heat, such as an overloaded engine or an air supply restriction.
      2. 2Work through the checks listed for 2288, starting at the turbocharger turbine intake temperature and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Turbocharger turbine intake temperature - above normal - moderately severe

  • Turbocharger compressor outlet temperature (calculated)1 code

    • Cummins 2347Turbocharger compressor outlet temperature (calculated): Above normal· least severe

      Same failure as 2288 on the turbocharger compressor outlet temperature: the same fault condition as 2288, reported for this part.· Real condition
      Info

      Causes

      • Same causes as 2288, applied to the turbocharger compressor outlet temperature
      • Wiring or connector problem local to the turbocharger compressor outlet temperature

      Checks

      1. 1Check the compressor inlet temperature and boost sensors, which this value is calculated from.
      2. 2Work through the checks listed for 2288, starting at the turbocharger compressor outlet temperature and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Turbocharger compressor outlet temperature (calculated) - above normal - least severe

  • Engine turbocharger 1 speed1 code

    • Cummins 5943Engine turbocharger 1 speed: Mechanical fault or not responding

      The ECM commands the engine turbocharger 1 speed but sees no matching response, so it reports a mechanical fault or a part that is not responding even though the wiring may be fine.· Part or controller
      Check soon

      Causes

      • Engine turbocharger 1 speed stuck, seized or restricted by dirt, soot or wear
      • Electrical supply too weak to move the part
      • Mechanical linkage or return spring broken

      Checks

      1. 1Command the engine turbocharger 1 speed with the service tool and watch or listen for it to move
      2. 2Remove the engine turbocharger 1 speed and inspect it for sticking, wear, carbon or debris
      3. 3Check supply voltage and ground at the engine turbocharger 1 speed while it is commanded
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Turbocharger 1 compressor intake temperature sensor1 code

    • Cummins 7861Turbocharger 1 compressor intake temperature sensor: Abnormal rate of change

      The turbocharger 1 compressor intake temperature sensor changed faster than it physically could, so the ECM treats the reading as a sensor or wiring problem and not as a real change.· Erratic or implausible
      Check soon

      Causes

      • Intermittent contact in the harness or connector of the turbocharger 1 compressor intake temperature sensor
      • Failing part giving unstable output
      • Poor ground or noisy supply feeding the circuit

      Checks

      1. 1Log the turbocharger 1 compressor intake temperature sensor while moving the harness and connector, and look for steps instead of smooth changes
      2. 2Inspect the turbocharger 1 compressor intake temperature sensor connector for water, corrosion and loose pins
      3. 3Check the supply and ground at the turbocharger 1 compressor intake temperature sensor while the engine runs
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

Shared checks

Checks, in order

  1. 1Check the turbo shaft for play and the compressor wheel for damage before anything else
  2. 2Check the air filter restriction and inlet piping for collapse before testing the sensor
  3. 3Check the air filter, charge-air cooler and cooling fan for restriction or poor airflow
  4. 4Inspect the sensor and its connector for heat damage and oil
  5. 5Compare the inlet pressure with barometric pressure at key on, engine off
  6. 6Review related temperature and pressure codes, because the calculation depends on them
  7. 7Watch turbo speed live while running the VGT actuator test; speed should rise smoothly with boost

Causes

  • Speed sensor air gap changed or sensor damaged
  • Restricted air filter or inlet piping making the inlet pressure genuinely low
  • Restricted air filter or charge-air cooler raising compressor outlet temperature
  • Harness chafed or corroded at the turbo connector

Most common here: real condition (8 of 17)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The ECM limits boost and torque to keep the turbo safe, so the engine feels weak under load.

Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.