EF Logo

Cummins · Air handling

Cummins EGR valve, position sensor and system performance fault codes

The position sensor built into the EGR valve tells the ECM how far the valve plate is open so it can close the loop on EGR flow. The ECM drives a motor inside the EGR valve to open and close it.

More about these parts

These codes come from the ECM's own EGR monitors rather than a single sensor.

FaultCheck1228Cummins · EGR valve position
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.

What do these codes mean?

Cummins codes 1228 to 7232 are all about the eGR valve, position sensor and system performance. The most common failure type is shorted low (3 of 15); none needs an immediate stop. Start with this check: command the EGR valve open and closed in INSITE and watch whether the position reading follows the command.

How urgent are they?

None of the 15 codes here means stop now; 14 can wait until the shift ends, but find the cause before the next one; 1 is information only.

  • Check soon14
  • Info1

What should I check first?

Command the EGR valve open and closed in INSITE and watch whether the position reading follows the command

Shared checks

15 of 15

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Cummins 1228EGR valve position - Erratic reading

    The ECM judges the EGR valve position to be erratic, intermittent or implausible.· Erratic or implausible
    Check soon

    Causes

    • Intermittent connector or wiring contact
    • Sensor ageing or failing
    • A real fluctuation in the system it measures

    Checks

    1. 1Watch the EGR valve position live and wiggle the harness and connector to catch dropouts
    2. 2Compare it with a related sensor to see which one is wrong
    3. 3Check the connector for moisture and corrosion
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

    Source wording:EGR valve position - data erratic or incorrect

  • Cummins 1896EGR valve controller - Out of calibration

    The ECM reports the EGR valve controller as out of calibration, so its value does not agree with the stored calibration or with the other data it is compared against.· Part or controller
    Check soon

    Causes

    • Sensor or device out of tolerance
    • Wrong calibration or learn data after a repair

    Checks

    1. 1Check whether a learn or calibration procedure is needed after the last repair
    2. 2Compare with a related sensor and replace the part if the offset is real
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Cummins 1961EGR valve control circuit calculated over temperature - Above normal· least severe

    The EGR valve control circuit calculated over temperature is above its normal operating range and the ECM rates it as least severe.· Real condition
    Info

    Causes

    • The monitored condition really is too high because of the system it measures
    • A related fault that set first and is pushing the reading out of range

    Checks

    1. 1Compare the live EGR valve control circuit calculated over temperature with a second reading or gauge to see whether the condition is real
    2. 2Read the freeze-frame for speed, load and temperature when the code set
    3. 3Clear any other active codes first and retest under load
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

    Source wording:EGR valve control circuit calculated over temperature - above normal - least severe

  • Cummins 2271EGR valve position sensor signal voltage high

    The ECM sees the EGR valve position sensor signal above its normal voltage band.· Shorted high
    Check soon

    Causes

    • EGR valve position sensor signal shorted to the reference inside the valve connector
    • Return wire open in the valve harness
    • Position sensor inside the valve failed high
    • Harness cooked by the EGR pipe next to it

    Checks

    1. 1Command the EGR valve closed in INSITE and see whether the position reads high with the valve shut
    2. 2Unplug the valve and measure reference and return at the harness
    3. 3Probe the position signal wire for a short to the reference
    4. 4Inspect the valve connector for heat damage and carbon
    5. 5Replace the EGR valve assembly only after the supply, return and signal wires all test good at the connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Cummins 2272EGR valve position sensor signal voltage low

    The ECM sees the EGR valve position sensor signal below its normal voltage band.· Shorted low
    Check soon

    Causes

    • EGR valve position signal wire chafed to ground
    • Reference wire open at the EGR valve connector
    • Position sensor in the valve failed low
    • Heat-damaged harness

    Checks

    1. 1Command the EGR valve open in INSITE and see whether the position reading stays low
    2. 2Measure the 5 V reference at the unplugged valve connector
    3. 3Ohm the signal wire to ground with the ECM unplugged
    4. 4Check the connector for a backed-out terminal
    5. 5Replace the EGR valve assembly only after the supply and signal wires test good and the valve still shows low position
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Cummins 2349EGR valve actuator open circuit

    The ECM finds no current flowing in the EGR valve actuator circuit when it commands it on, so the circuit is open or the load is unplugged.· Open circuit
    Check soon

    Causes

    • EGR valve motor winding open
    • Valve driver wire broken near the valve connector
    • Connector pin burnt by exhaust heat

    Checks

    1. 1Command the EGR valve in INSITE and see whether any current flows
    2. 2Measure the valve motor winding resistance against the service value
    3. 3Test both EGR valve driver wires for continuity between the valve plug and the ECM connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Cummins 2351EGR valve actuator shorted low or driver voltage low

    The ECM drives the EGR valve actuator but sees its output pulled to ground.· Shorted low
    Check soon

    Causes

    • EGR valve driver wire shorted to ground
    • Valve motor winding shorted internally
    • Connector wet or melted

    Checks

    1. 1Unplug the valve; if the code changes to open circuit, the valve was shorted
    2. 2Measure each driver wire to ground at the harness with the key off
    3. 3Check the EGR valve motor winding resistance against the service value to see whether it is shorted
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Cummins 2352EGR valve actuator shorted high or driver voltage high

    The ECM drives the EGR valve actuator but sees its output voltage higher than commanded.· Shorted high
    Check soon

    Causes

    • EGR valve driver wire shorted to a supply
    • Open ground at the valve
    • ECM output fault (rare)

    Checks

    1. 1Unplug the valve and measure the driver pin at the harness with the key on
    2. 2Check the valve ground (return) wire for continuity to the ECM and for a loose pin
    3. 3Inspect the EGR valve connector for pins touching each other or a cracked housing
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Cummins 2353EGR valve control circuit - Current high / grounded

    The ECM sees too much current in the EGR valve control circuit, which points to a short to ground in the wiring or a winding that has shorted inside the component.· Shorted low
    Check soon

    Causes

    • Wire shorted to ground or chafed to the chassis
    • Shorted winding inside the component

    Checks

    1. 1Unplug the EGR valve control circuit connector and see whether the fault clears; if so the component is likely at fault
    2. 2Test the harness for a short to ground with the key off
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

    Source wording:EGR valve control circuit - current high or grounded circuit

  • Cummins 2357EGR valve control circuit - Mechanical fault or not responding

    The ECM commands the EGR valve control circuit but it does not respond as expected, or its movement is out of adjustment.· Part or controller
    Check soon

    Causes

    • Mechanism seized, sooted or blocked
    • Wear or incorrect adjustment of the linkage or part
    • Supply or return fault limiting its movement

    Checks

    1. 1Command the EGR valve control circuit in INSITE and watch whether it moves and returns
    2. 2Inspect the part and its linkage for sticking, debris or wear
    3. 3Check supply and return connections before replacing it
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Cummins 3342EGR cooler efficiency low

    The EGR cooler is not lowering the gas temperature as much as expected.· Other
    Check soon

    Causes

    • EGR cooler fouled inside
    • Low coolant flow or air in the cooling system
    • EGR temperature sensor reading wrong

    Checks

    1. 1Check the coolant level and look for air trapped in the system
    2. 2Compare the EGR temperature before and after the cooler
    3. 3Check the thermostat opens fully at operating temperature
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Cummins 3382EGR system flow low· moderately severe

    The EGR system is not flowing as much exhaust gas as the ECM wants, so NOx control suffers.· Other
    Check soon

    Causes

    • EGR valve stuck closed or sticking with carbon
    • EGR cooler or pipe blocked with soot
    • EGR delta pressure sensor lines blocked

    Checks

    1. 1Run the EGR valve test in INSITE and watch whether the valve opens as commanded
    2. 2Inspect the delta pressure sensor lines for soot blockage or splitting
    3. 3Check the EGR cooler for soot blockage that restricts the flow
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

    Source wording:EGR system flow low - moderately severe

  • Cummins 3383Engine EGR system - Above normal· moderately severe

    The engine EGR system is above its normal operating range and the ECM rates it as moderately severe.· Real condition
    Check soon

    Causes

    • The monitored condition really is too high because of the system it measures
    • A related fault that set first and is pushing the reading out of range

    Checks

    1. 1Compare the live engine EGR system with a second reading or gauge to see whether the condition is real
    2. 2Read the freeze-frame for speed, load and temperature when the code set
    3. 3Clear any other active codes first and retest under load
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

    Source wording:Engine EGR system - above normal - moderately severe

  • Cummins 3389Engine EGR system - Abnormal rate of change

    The engine EGR system reading is changing faster than the real quantity could move.· Erratic or implausible
    Check soon

    Causes

    • Loose or corroded connector causing intermittent contact
    • Intermittent wiring fault that opens and closes
    • Sensor starting to fail

    Checks

    1. 1Watch the engine EGR system reading live and wiggle the harness and connector to see whether it jumps
    2. 2Inspect the connector pins for corrosion and spread terminals
    3. 3Compare with a related sensor to see whether the jump is real
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Cummins 7232Engine EGR system - Above normal· most severe

    The engine EGR system is above its normal operating range and the ECM rates it as most severe.· Real condition
    Check soon

    Causes

    • The monitored condition really is too high because of the system it measures
    • A related fault that set first and is pushing the reading out of range

    Checks

    1. 1Compare the live engine EGR system with a second reading or gauge to see whether the condition is real
    2. 2Read the freeze-frame for speed, load and temperature when the code set
    3. 3Clear any other active codes first and retest under load
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

    Source wording:Engine EGR system - above normal - most severe

Shared checks

Checks, in order

  1. 1Command the EGR valve open and closed in INSITE and watch whether the position reading follows the command
  2. 2Run the EGR valve test in INSITE and watch the commanded and actual position together
  3. 3Clear all sensor and circuit codes first, because the flow monitor is only valid when the sensors are healthy
  4. 4Unplug the valve and check reference and return at the harness before condemning the valve
  5. 5Measure the drive wires for continuity and for shorts to ground and battery with the connector unplugged
  6. 6Run the EGR valve test and confirm the valve opens and closes fully
  7. 7Inspect the connector for burnt or loose terminals near the EGR pipe

Causes

  • Carbon or heat damage inside the valve connector
  • Open, shorted or high-resistance wire in the valve drive harness
  • EGR valve stuck or sooted so flow does not match the command
  • Open return or reference wire in the valve harness

Most common here: shorted low (3 of 15)

Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

When to stop

You'll notice: EGR flow is not controlled accurately, so the engine may smoke, run rough or lose power and the ECM may close the valve.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.