EF Logo

Cummins · Air handling

Cummins Exhaust gas pressure and ambient air sensors fault codes

Pressure sensors in the exhaust, before the turbine or on a second bank, measure back-pressure so the ECM can control EGR and protect the turbo. The ECM reads outside air temperature and barometric pressure, either from its own sensors or from the vehicle network, and uses them to correct fuelling and derate for altitude.

FaultCheck221Cummins · Barometric pressure sensor circuit
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.

What do these codes mean?

Cummins codes 221 to 7864 are all about the exhaust gas pressure and ambient air sensors. The most common failure type is real condition (7 of 25); none needs an immediate stop. Start with this check: compare the sensor reading at key on, engine off with barometric pressure.

How urgent are they?

None of the 25 codes here means stop now; 21 can wait until the shift ends, but find the cause before the next one; 4 are information only.

  • Check soon21
  • Info4

What should I check first?

Compare the sensor reading at key on, engine off with barometric pressure

Shared checks

25 of 25

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Barometric pressure sensor circuit2 codes

    • Cummins 221Barometric pressure sensor circuit: Voltage high / shorted high

      Same failure as 2373 on the barometric pressure sensor circuit: the same fault condition as 2373, reported for this part.· Shorted high
      Check soon

      Causes

      • Same causes as 2373, applied to the barometric pressure sensor circuit
      • Wiring or connector problem local to the barometric pressure sensor circuit

      Checks

      1. 1Compare the reading with the local barometric pressure at key on, engine off.
      2. 2Work through the checks listed for 2373, starting at the barometric pressure sensor circuit and its connector
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Barometric pressure sensor circuit - voltage high (shorted to a high source)

    • Cummins 222Barometric pressure sensor circuit: Voltage low / shorted low

      Same failure as 2374 on the barometric pressure sensor circuit: the same fault condition as 2374, reported for this part.· Shorted low
      Check soon

      Causes

      • Same causes as 2374, applied to the barometric pressure sensor circuit
      • Wiring or connector problem local to the barometric pressure sensor circuit

      Checks

      1. 1Compare the reading with the local barometric pressure at key on, engine off.
      2. 2Work through the checks listed for 2374, starting at the barometric pressure sensor circuit and its connector
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Barometric pressure sensor circuit - voltage low (shorted to a low source)

  • Ambient air temperature sensor 1 circuit2 codes

    • Cummins 249Ambient air temperature sensor 1 circuit: Voltage high / shorted high

      Same failure as 2373 on the ambient air temperature sensor 1 circuit: the same fault condition as 2373, reported for this part.· Shorted high
      Check soon

      Causes

      • Same causes as 2373, applied to the ambient air temperature sensor 1 circuit
      • Wiring or connector problem local to the ambient air temperature sensor 1 circuit

      Checks

      1. 1Compare it with a thermometer in the shade and check whether the vehicle or the engine supplies the value.
      2. 2Work through the checks listed for 2373, starting at the ambient air temperature sensor 1 circuit and its connector
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Ambient air temperature sensor 1 circuit - voltage high (shorted to a high source)

    • Cummins 256Ambient air temperature sensor 1 circuit: Voltage low / shorted low

      Same failure as 2374 on the ambient air temperature sensor 1 circuit: the same fault condition as 2374, reported for this part.· Shorted low
      Check soon

      Causes

      • Same causes as 2374, applied to the ambient air temperature sensor 1 circuit
      • Wiring or connector problem local to the ambient air temperature sensor 1 circuit

      Checks

      1. 1Compare it with a thermometer in the shade and check whether the vehicle or the engine supplies the value.
      2. 2Work through the checks listed for 2374, starting at the ambient air temperature sensor 1 circuit and its connector
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Ambient air temperature sensor 1 circuit - voltage low (shorted to a low source)

  • Barometric pressure1 code

    • Cummins 295Barometric pressure: Erratic reading

      Same failure as 2554 on the barometric pressure: the same fault condition as 2554, reported for this part.· Erratic or implausible
      Check soon

      Causes

      • Same causes as 2554, applied to the barometric pressure
      • Wiring or connector problem local to the barometric pressure

      Checks

      1. 1Compare the reading with the local barometric pressure at key on, engine off.
      2. 2Work through the checks listed for 2554, starting at the barometric pressure and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:Barometric pressure - data erratic or incorrect

  • Ambient air density1 code

    • Cummins 1943Ambient air density: Below normal· least severe

      Same failure as 7273 on the ambient air density: the same fault condition as 7273, reported for this part.· Real condition
      Info

      Causes

      • Same causes as 7273, applied to the ambient air density
      • Wiring or connector problem local to the ambient air density

      Checks

      1. 1Check the barometric and ambient temperature readings that this value is calculated from.
      2. 2Work through the checks listed for 7273, starting at the ambient air density and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Ambient air density - below normal - least severe

  • Exhaust gas pressure sensor circuit2 codes

    • Cummins 2373Exhaust gas pressure sensor circuit: Voltage high / shorted high

      The ECM reads the exhaust gas pressure sensor circuit above its allowed voltage band.· Shorted high
      Check soon

      Causes

      • Short to a 5 V reference or a battery wire in the harness to the exhaust gas pressure sensor circuit
      • Open or high-resistance return wire that lets the signal float high
      • Water or corrosion in the connector bridging two pins together

      Checks

      1. 1Key on, unplug the exhaust gas pressure sensor circuit and read its circuit at the harness: a high reading with the part removed means the wiring is shorted high or the return is lost
      2. 2Jumper the signal wire of the exhaust gas pressure sensor circuit to ground at the harness and see whether the code changes to a low-voltage code, which proves the wiring and the ECM input
      3. 3Check continuity and resistance of the return wire from the exhaust gas pressure sensor circuit back to the ECM
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Exhaust gas pressure sensor circuit - voltage high (shorted to a high source)

    • Cummins 2374Exhaust gas pressure sensor circuit: Voltage low / shorted low

      The ECM reads the exhaust gas pressure sensor circuit below its allowed voltage band.· Shorted low
      Check soon

      Causes

      • Signal wire to the exhaust gas pressure sensor circuit rubbed through and shorted to ground or to the engine block
      • Open 5 V reference or open signal wire that lets the input drop to zero
      • Corroded or backed-out pin in the exhaust gas pressure sensor circuit connector

      Checks

      1. 1Key on, unplug the exhaust gas pressure sensor circuit and read its circuit at the harness: a reading near zero with the part removed means the wiring is shorted to ground or open
      2. 2Jumper the 5 V reference to the signal wire at the harness and see whether the code changes to a high-voltage code, which proves the wiring and the ECM input
      3. 3Measure resistance from the exhaust gas pressure sensor circuit signal wire to ground with the ECM unplugged to find a short
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Exhaust gas pressure sensor circuit - voltage low (shorted to a low source)

  • Ambient air temperature4 codes

    • Cummins 2398Ambient air temperature: Erratic reading

      Same failure as 2554 on the ambient air temperature: the same fault condition as 2554, reported for this part.· Lost message
      Check soon

      Causes

      • Same causes as 2554, applied to the ambient air temperature
      • Wiring or connector problem local to the ambient air temperature

      Checks

      1. 1Compare it with a thermometer in the shade and check whether the vehicle or the engine supplies the value.
      2. 2Work through the checks listed for 2554, starting at the ambient air temperature and its connector
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

      Source wording:Ambient air temperature - data erratic or incorrect

    • Cummins 3531Ambient air temperature: Abnormal update rate

      The ECM is not receiving fresh data for the ambient air temperature at the expected rate.· Lost message
      Check soon

      Causes

      • Data link wiring fault or a poor connector contact
      • The module that sends the message for the ambient air temperature is offline or failing
      • Power or ground problem at the sending module

      Checks

      1. 1Look for other modules reporting timeouts to find where the link is broken
      2. 2Check the data link wiring, connectors and both terminators near the ambient air temperature source
      3. 3Read the module that sends the ambient air temperature for its own codes and for power or ground faults
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

    • Cummins 3532Ambient air temperature: Network data in error

      The ECM received data for the ambient air temperature over the network, but the message was flagged as in error.· Lost message
      Check soon

      Causes

      • Sending module flagging the data as not available or in error
      • Data link noise, a wiring fault or a bad terminator
      • Mismatched configuration between the ECM and the sending module

      Checks

      1. 1Read the sending module for its own codes and the source sensor for faults
      2. 2Check the data link wiring and terminators for faults near the ambient air temperature source
      3. 3Check the ECM and sending module configuration for the ambient air temperature
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

      Source wording:Ambient air temperature - network data received in error

    • Cummins 7863Ambient air temperature: Abnormal rate of change

      Same failure as 7864 on the ambient air temperature: the same fault condition as 7864, reported for this part.· Lost message
      Check soon

      Causes

      • Same causes as 7864, applied to the ambient air temperature
      • Wiring or connector problem local to the ambient air temperature

      Checks

      1. 1Compare it with a thermometer in the shade and check whether the vehicle or the engine supplies the value.
      2. 2Work through the checks listed for 7864, starting at the ambient air temperature and its connector
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Exhaust gas pressure6 codes

    • Cummins 2554Exhaust gas pressure: Erratic reading

      The ECM judges the exhaust gas pressure to be erratic or implausible: the value jumps, drifts or disagrees with related readings, which suggests a poor connection or a part on its way out.· Erratic or implausible
      Check soon

      Causes

      • Intermittent connector or wiring contact on the exhaust gas pressure
      • Part ageing or failing and giving unstable output
      • Electrical noise from a poorly routed wire or a bad ground

      Checks

      1. 1Watch the exhaust gas pressure live in INSITE and wiggle the harness and connector to catch dropouts
      2. 2Compare the exhaust gas pressure with a related reading to decide which one is wrong
      3. 3Check the connector for moisture and corrosion and the ground connection for tightness
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:Exhaust gas pressure - data erratic or incorrect

    • Cummins 2764Exhaust gas pressure: Above normal· moderately severe

      The exhaust gas pressure is above its normal range (severity: moderately severe).· Real condition
      Check soon

      Causes

      • A real over-limit condition in the system the exhaust gas pressure measures
      • Sensor or circuit reading high from a wiring fault
      • A cooling, flow or restriction problem upstream that drives the value up

      Checks

      1. 1Confirm the real condition with a gauge or a second reading before replacing the exhaust gas pressure
      2. 2Check that the exhaust gas pressure circuit codes are not active, since a wiring fault can fake a high reading
      3. 3Look for the physical cause upstream, such as restriction, leakage, poor cooling or heavy load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Exhaust gas pressure - above normal - moderately severe

    • Cummins 4728Exhaust gas pressure: Below normal· moderately severe

      Same failure as 7273 on the exhaust gas pressure: the same fault condition as 7273, reported for this part.· Real condition
      Check soon

      Causes

      • Same causes as 7273, applied to the exhaust gas pressure
      • Wiring or connector problem local to the exhaust gas pressure

      Checks

      1. 1Clear the sensor sensing tube of soot and check the sensor on the first exhaust path.
      2. 2Work through the checks listed for 7273, starting at the exhaust gas pressure and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Exhaust gas pressure - below normal - moderately severe

    • Cummins 7273Exhaust gas pressure: Below normal· least severe

      The exhaust gas pressure is below its normal range (severity: least severe).· Real condition
      Info

      Causes

      • A real shortfall in the system the exhaust gas pressure measures
      • Sensor or circuit reading low from a wiring fault
      • A leak, low level or weak supply that lets the value fall

      Checks

      1. 1Confirm the real condition with a gauge or a second reading before replacing the exhaust gas pressure
      2. 2Check that the exhaust gas pressure circuit codes are not active, since a wiring fault can fake a low reading
      3. 3Look for the physical cause upstream, such as a leak, low fluid, weak pump or blocked supply
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Exhaust gas pressure - below normal - least severe

    • Cummins 7582Exhaust gas pressure: Below normal· least severe

      Same failure as 7273 on the exhaust gas pressure: the same fault condition as 7273, reported for this part.· Real condition
      Info

      Causes

      • Same causes as 7273, applied to the exhaust gas pressure
      • Wiring or connector problem local to the exhaust gas pressure

      Checks

      1. 1Clear the sensor sensing tube of soot and check the sensor on the first exhaust path.
      2. 2Work through the checks listed for 7273, starting at the exhaust gas pressure and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Exhaust gas pressure - below normal - least severe

    • Cummins 7864Exhaust gas pressure: Abnormal rate of change

      The exhaust gas pressure changed faster than it physically could, so the ECM treats the reading as a sensor or wiring problem and not as a real change.· Erratic or implausible
      Check soon

      Causes

      • Intermittent contact in the harness or connector of the exhaust gas pressure
      • Failing part giving unstable output
      • Poor ground or noisy supply feeding the circuit

      Checks

      1. 1Log the exhaust gas pressure while moving the harness and connector, and look for steps instead of smooth changes
      2. 2Inspect the exhaust gas pressure connector for water, corrosion and loose pins
      3. 3Check the supply and ground at the exhaust gas pressure while the engine runs
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Engine exhaust gas pressure 21 code

    • Cummins 4126Engine exhaust gas pressure 2: Above normal· moderately severe

      Same failure as 2764 on the engine exhaust gas pressure 2: the same fault condition as 2764, reported for this part.· Real condition
      Check soon

      Causes

      • Same causes as 2764, applied to the engine exhaust gas pressure 2
      • Wiring or connector problem local to the engine exhaust gas pressure 2

      Checks

      1. 1Clear the sensing tube of this second sensor and compare its reading with the first exhaust pressure sensor.
      2. 2Work through the checks listed for 2764, starting at the engine exhaust gas pressure 2 and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Engine exhaust gas pressure 2 - above normal - moderately severe

  • Engine exhaust gas bank 2 pressure sensor 12 codes

    • Cummins 4127Engine exhaust gas bank 2 pressure sensor 1: Voltage high / shorted high

      Same failure as 2373 on the engine exhaust gas bank 2 pressure sensor 1: the same fault condition as 2373, reported for this part.· Shorted high
      Check soon

      Causes

      • Same causes as 2373, applied to the engine exhaust gas bank 2 pressure sensor 1
      • Wiring or connector problem local to the engine exhaust gas bank 2 pressure sensor 1

      Checks

      1. 1Clear the sensing tube of this second sensor and compare its reading with the first exhaust pressure sensor.
      2. 2Work through the checks listed for 2373, starting at the engine exhaust gas bank 2 pressure sensor 1 and its connector
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Engine exhaust gas bank 2 pressure sensor 1 - voltage high (shorted to a high source)

    • Cummins 4128Engine exhaust gas bank 2 pressure sensor 1: Voltage low / shorted low

      Same failure as 2374 on the engine exhaust gas bank 2 pressure sensor 1: the same fault condition as 2374, reported for this part.· Shorted low
      Check soon

      Causes

      • Same causes as 2374, applied to the engine exhaust gas bank 2 pressure sensor 1
      • Wiring or connector problem local to the engine exhaust gas bank 2 pressure sensor 1

      Checks

      1. 1Clear the sensing tube of this second sensor and compare its reading with the first exhaust pressure sensor.
      2. 2Work through the checks listed for 2374, starting at the engine exhaust gas bank 2 pressure sensor 1 and its connector
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Engine exhaust gas bank 2 pressure sensor 1 - voltage low (shorted to a low source)

  • Engine exhaust pressure 21 code

    • Cummins 7193Engine exhaust pressure 2: Below normal· moderately severe

      Same failure as 7273 on the engine exhaust pressure 2: the same fault condition as 7273, reported for this part.· Real condition
      Check soon

      Causes

      • Same causes as 7273, applied to the engine exhaust pressure 2
      • Wiring or connector problem local to the engine exhaust pressure 2

      Checks

      1. 1Clear the sensing tube of this second sensor and compare its reading with the first exhaust pressure sensor.
      2. 2Work through the checks listed for 7273, starting at the engine exhaust pressure 2 and its connector
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Engine exhaust pressure 2 - below normal - moderately severe

  • Engine exhaust gas pressure 2 sensor3 codes

    • Cummins 7218Engine exhaust gas pressure 2 sensor: Condition exists

      The ECM has flagged a condition on the engine exhaust gas pressure 2 sensor.· Other
      Info

      Causes

      • The underlying system problem that the ECM is reporting on the engine exhaust gas pressure 2 sensor
      • A related sensor or circuit fault that triggered this condition
      • Operating conditions outside what the strategy expects

      Checks

      1. 1Read all active and inactive codes and work the circuit or sensor codes for the engine exhaust gas pressure 2 sensor first
      2. 2Check the live data around the engine exhaust gas pressure 2 sensor while reproducing the operating condition
      3. 3Inspect the system the engine exhaust gas pressure 2 sensor belongs to for leaks, blockage or damage
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

    • Cummins 7446Engine exhaust gas pressure 2 sensor: Reading drifted low

      The engine exhaust gas pressure 2 sensor reads lower than the ECM calculates it should, and it has crept downward over time.· Erratic or implausible
      Check soon

      Causes

      • Sensing element ageing and reading low
      • Sensor port blocked or leaking so it does not see the true value
      • Slow rise in resistance in a connector or wire

      Checks

      1. 1Compare the engine exhaust gas pressure 2 sensor with a known good sensor or a reference gauge at the same operating point
      2. 2Inspect the engine exhaust gas pressure 2 sensor sensing port and seals for blockage or leakage
      3. 3Measure the voltage drop in the wiring to the engine exhaust gas pressure 2 sensor for extra resistance
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:Engine exhaust gas pressure 2 sensor - data drifted low

    • Cummins 7447Engine exhaust gas pressure 2 sensor: Reading drifted high

      The engine exhaust gas pressure 2 sensor reads higher than the ECM calculates it should, and it has crept upward over time.· Erratic or implausible
      Check soon

      Causes

      • Sensing element ageing and reading high
      • Sensor contaminated by soot, oil or deposits
      • Slow rise in resistance in a connector or wire

      Checks

      1. 1Compare the engine exhaust gas pressure 2 sensor with a known good sensor or a reference gauge at the same operating point
      2. 2Clean or replace the engine exhaust gas pressure 2 sensor if it is contaminated, and check its sensing port for blockage
      3. 3Measure the voltage drop in the wiring to the engine exhaust gas pressure 2 sensor for extra resistance
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:Engine exhaust gas pressure 2 sensor - data drifted high

Shared checks

Checks, in order

  1. 1Compare the sensor reading at key on, engine off with barometric pressure
  2. 2Compare the ambient temperature and barometric pressure with a known reference or other vehicle data
  3. 3Remove the sensing tube and clear soot with compressed air
  4. 4Inspect the sensor and its connector, which are often exposed at the grille or ECM
  5. 5Check reference, return and signal at the sensor with it unplugged
  6. 6Check whether the value arrives over J1939 and look for data-link faults
  7. 7Inspect the exhaust system for leaks or blockage

Causes

  • Sensor sense line plugged with soot or burnt
  • Sensor or harness damaged at the front of the vehicle
  • Exhaust restriction or leak changing the real pressure
  • Connector corrosion from road spray

Most common here: real condition (7 of 25)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: The ECM may limit EGR or boost, and the engine can show a derate when exhaust pressure looks abnormal.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.