EF Logo

Cummins · Aftertreatment

Cummins DPF regeneration status, inhibit and switches fault codes

These codes are not component faults. Cab switches let the operator inhibit or request a DPF regeneration.

FaultInfo2777Cummins · DPF active regeneration inhibited due to inhibit switch
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.

What do these codes mean?

Cummins codes 2777 to 14357 are all about the dPF regeneration status, inhibit and switches. The most common failure type is lost message (3 of 14); none needs an immediate stop. Start with this check: check the regeneration inhibit switch position and the regeneration settings.

How urgent are they?

None of the 14 codes here means stop now; 8 can wait until the shift ends, but find the cause before the next one; 6 are information only.

  • Check soon8
  • Info6

What should I check first?

Check the regeneration inhibit switch position and the regeneration settings

Shared checks

14 of 14

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • DPF active regeneration inhibited due to inhibit switch2 codes

    • Cummins 2777DPF active regeneration inhibited due to inhibit switch: Condition exists

      The ECM sets this code when it recognises a defined condition for the DPF active regeneration inhibited due to inhibit switch.· Other
      Info

      Causes

      • A monitor or protection condition that has been met
      • A related fault that set first

      Checks

      1. 1Read the code description and freeze-frame in INSITE for the exact condition
      2. 2Work the related active codes first, then recheck
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

    • Cummins 6416DPF active regeneration inhibited due to inhibit switch: Condition exists

      The ECM sets this code when it recognises a defined condition for the DPF active regeneration inhibited due to inhibit switch.· Other
      Info

      Causes

      • A monitor or protection condition that has been met
      • A related fault that set first

      Checks

      1. 1Read the code description and freeze-frame in INSITE for the exact condition
      2. 2Work the related active codes first, then recheck
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

  • DPF1 code

    • Cummins 3396DPF: Conditions not met for active regeneration

      The ECM wants to regenerate the DPF but a condition such as speed, coolant temperature, or a switch prevents it.· Other
      Info

      Causes

      • Regeneration inhibit switch on
      • Coolant too cold
      • Machine not in the right state, e.g. not parked with the brake

      Checks

      1. 1Check the regeneration inhibit switch is not left on
      2. 2Warm the engine to operating temperature because regeneration is blocked when the coolant is cold
      3. 3Follow the correct parked regeneration conditions
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

  • DPF active regeneration inhibited due to low exhaust gas temperature1 code

    • Cummins 3495DPF active regeneration inhibited due to low exhaust gas temperature: Condition exists

      The ECM sets this code when it recognises a defined condition for the DPF active regeneration inhibited due to low exhaust gas temperature.· Other
      Info

      Causes

      • A monitor or protection condition that has been met
      • A related fault that set first

      Checks

      1. 1Read the code description and freeze-frame in INSITE for the exact condition
      2. 2Work the related active codes first, then recheck
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Aftertreatment regeneration force switch2 codes

    • Cummins 3696Aftertreatment regeneration force switch: Out of calibration

      The ECM reports the aftertreatment regeneration force switch as out of calibration, meaning the value or setting it received does not match what it was programmed to expect.· Part or controller
      Check soon

      Causes

      • Parameter set for a feature that is not fitted
      • Wrong or outdated calibration in the ECM
      • Source module sending an invalid value

      Checks

      1. 1Compare the ECM parameters with the vehicle equipment
      2. 2Reflash the ECM with the correct calibration
      3. 3Read the source module for its own codes
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 14355Aftertreatment regeneration force switch: Abnormal update rate

      The ECM is not receiving fresh data for the aftertreatment regeneration force switch at the expected rate.· Lost message
      Check soon

      Causes

      • Data link wiring fault or a poor connector contact
      • The module that sends the message is offline or failing
      • Power or ground problem at the sending module

      Checks

      1. 1Look for other modules reporting timeouts to find where the link is broken
      2. 2Check the data link wiring, connectors and terminators
      3. 3Read the sending module for its own codes
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • DPF active regeneration inhibited due to system timeout1 code

    • Cummins 3753DPF active regeneration inhibited due to system timeout: Condition exists

      The ECM sets this code when it recognises a defined condition for the DPF active regeneration inhibited due to system timeout.· Lost message
      Info

      Causes

      • A monitor or protection condition that has been met
      • A related fault that set first

      Checks

      1. 1Read the code description and freeze-frame in INSITE for the exact condition
      2. 2Work the related active codes first, then recheck
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Aftertreatment regeneration inhibit switch3 codes

    • Cummins 4213Aftertreatment regeneration inhibit switch: Erratic reading

      The ECM judges the aftertreatment regeneration inhibit switch to be erratic, intermittent or implausible.· Erratic or implausible
      Check soon

      Causes

      • Intermittent connector or wiring contact
      • Sensor ageing or failing
      • A real fluctuation in the system it measures

      Checks

      1. 1Watch the aftertreatment regeneration inhibit switch live and wiggle the harness and connector to catch dropouts
      2. 2Compare it with a related sensor to see which one is wrong
      3. 3Check the connector for moisture and corrosion
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:Aftertreatment regeneration inhibit switch - data erratic or incorrect

    • Cummins 14356Aftertreatment regeneration inhibit switch: Out of calibration

      The ECM reports the aftertreatment regeneration inhibit switch as out of calibration, meaning the value or setting it received does not match what it was programmed to expect.· Part or controller
      Check soon

      Causes

      • Parameter set for a feature that is not fitted
      • Wrong or outdated calibration in the ECM
      • Source module sending an invalid value

      Checks

      1. 1Compare the ECM parameters with the vehicle equipment
      2. 2Reflash the ECM with the correct calibration
      3. 3Read the source module for its own codes
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 14357Aftertreatment regeneration inhibit switch: Abnormal update rate

      The ECM is not receiving fresh data for the aftertreatment regeneration inhibit switch at the expected rate.· Lost message
      Check soon

      Causes

      • Data link wiring fault or a poor connector contact
      • The module that sends the message is offline or failing
      • Power or ground problem at the sending module

      Checks

      1. 1Look for other modules reporting timeouts to find where the link is broken
      2. 2Check the data link wiring, connectors and terminators
      3. 3Read the sending module for its own codes
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • DPF ash load percent1 code

    • Cummins 5383DPF ash load percent: Above normal· least severe

      The DPF ash load percent is above its normal operating range and the ECM rates it as least severe.· Real condition
      Info

      Causes

      • The monitored condition really is too high because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live DPF ash load percent with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:DPF ash load percent - above normal - least severe

  • Aftertreatment thermal management status1 code

    • Cummins 7224Aftertreatment thermal management status: Below normal· moderately severe

      The aftertreatment thermal management status is below its normal operating range and the ECM rates it as moderately severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too low because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live aftertreatment thermal management status with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Aftertreatment thermal management status - below normal - moderately severe

  • Other codes2 codes

    • Cummins 3375DPF regeneration happening too often

      The ECM has counted too many regenerations in a short time.· Other
      Check soon

      Causes

      • Engine making too much soot from an injector, EGR or air fault
      • Differential pressure sensor reading high
      • Short-duty use with many interrupted regenerations
      • DOC not working well

      Checks

      1. 1Check for fuel, air and EGR codes that make soot
      2. 2Check the differential pressure at idle with the engine off and on
      3. 3Check the DPF pressure sensor lines for blockage, which fools the ECM into regenerating
      4. 4Check the DOC performance and the regeneration temperatures in INSITE
      5. 5Review how the machine is used and whether regenerations are interrupted
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

    • Cummins 3376DPF regeneration incomplete

      A regeneration started but did not finish.· Other
      Check soon

      Causes

      • Regeneration interrupted by key off or by the inhibit switch
      • Exhaust temperature not reaching the target
      • Doser or fuel injector fault
      • DOC failed

      Checks

      1. 1Check whether the machine is being shut off during regeneration
      2. 2Check the regeneration inhibit switch is not left on, which stops the regeneration
      3. 3Read the DPF temperatures during a parked regeneration
      4. 4Check the doser or the late injection operation
      5. 5Check the DOC condition and the temperature rise across it during a regeneration
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Check the regeneration inhibit switch position and the regeneration settings
  2. 2Watch the switch state in INSITE while pressing it
  3. 3Review the duty cycle; short trips and long idle prevent regeneration
  4. 4Check the switch wiring and connector for damage
  5. 5Check the DOC, doser and exhaust temperature sensors for faults
  6. 6Look at the data link for missing switch messages
  7. 7Look at the DPF soot and ash load and plan cleaning if needed

Causes

  • Regeneration inhibit switch left on
  • Switch failure or wiring fault
  • Exhaust temperature too low for regeneration, often from duty cycle
  • Data link message missing

Most common here: lost message (3 of 14)

Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

When to stop

You'll notice: The DPF lamp comes on and soot builds up; if ignored the engine will derate.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.