Cummins · Aftertreatment
Cummins DOC and DPF exhaust temperature sensors fault codes
Thermistor-type exhaust temperature sensors sit before and after the diesel oxidation catalyst (DOC) and at the DPF inlet and outlet. The ECM uses them to see whether the DOC is heating the exhaust, to control regeneration and to protect the filter from over-temperature.
Where to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
What do these codes mean?
Cummins codes 3251 to 7894 are all about the dOC and DPF exhaust temperature sensors. The most common failure type is erratic or implausible (11 of 25); 2 need an immediate stop. Start with this check: read the DOC and DPF temperatures live with the engine cold: all four should match ambient and each other.
How urgent are they?
2 of 25 codes here mean stop now; 21 can wait until the shift ends, but find the cause before the next one; 2 are information only.
- Stop now2
- Check soon21
- Info2
What should I check first?
Read the DOC and DPF temperatures live with the engine cold: all four should match ambient and each other
Shared checks25 of 25
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
DOC intake temperature2 codes
Cummins 3251DOC intake temperature: Above normal· moderately severe
Same failure as 3311 on the DOC intake temperature: the same fault condition as 3311, reported for this part. The DOC intake sensor sits before the diesel oxidation catalyst and shows whether the exhaust is hot enough for the catalyst to light off.· Real conditionReal conditionCheck soonCauses
- Same causes as 3311, applied to the DOC intake temperature
- Wiring or connector problem local to the DOC intake temperature
Checks
- 1Compare it with the DOC outlet reading on a warm engine: the outlet should be warmer only when the catalyst is working.
- 2Work through the checks listed for 3311, starting at the DOC intake temperature and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:DOC intake temperature - above normal - moderately severe
Cummins 3315DOC intake temperature: Erratic reading
Same failure as 3318 on the DOC intake temperature: the same fault condition as 3318, reported for this part. The DOC intake sensor sits before the diesel oxidation catalyst and shows whether the exhaust is hot enough for the catalyst to light off.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 3318, applied to the DOC intake temperature
- Wiring or connector problem local to the DOC intake temperature
Checks
- 1Compare it with the DOC outlet reading on a warm engine: the outlet should be warmer only when the catalyst is working.
- 2Work through the checks listed for 3318, starting at the DOC intake temperature and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:DOC intake temperature - data erratic or incorrect
DPF intake temperature4 codes
Cummins 3253DPF intake temperature: Above normal· moderately severe
Same failure as 3311 on the DPF intake temperature: the same fault condition as 3311, reported for this part. The DPF intake sensor sits at the filter inlet and protects the filter from over-temperature during regeneration.· Real conditionReal conditionCheck soonCauses
- Same causes as 3311, applied to the DPF intake temperature
- Wiring or connector problem local to the DPF intake temperature
Checks
- 1Compare it with the DOC outlet reading, which should be close when no heat is lost between them.
- 2Work through the checks listed for 3311, starting at the DPF intake temperature and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:DPF intake temperature - above normal - moderately severe
Cummins 3254DPF intake temperature: Above normal· least severe
Same failure as 3311 on the DPF intake temperature: the same fault condition as 3311, reported for this part. The DPF intake sensor sits at the filter inlet and protects the filter from over-temperature during regeneration.· Real conditionReal conditionInfoCauses
- Same causes as 3311, applied to the DPF intake temperature
- Wiring or connector problem local to the DPF intake temperature
Checks
- 1Compare it with the DOC outlet reading, which should be close when no heat is lost between them.
- 2Work through the checks listed for 3311, starting at the DPF intake temperature and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:DPF intake temperature - above normal - least severe
Cummins 3311DPF intake temperature: Above normal· most severe
The DPF intake temperature is above its normal range (severity: most severe). The ECM sets the code from a real reading, so look for a genuine cause before blaming the sensor. The DPF intake sensor sits at the filter inlet and protects the filter from over-temperature during regeneration.· Real conditionReal conditionStop nowCauses
- A real over-limit condition in the system the DPF intake temperature measures
- Sensor or circuit reading high from a wiring fault
- A cooling, flow or restriction problem upstream that drives the value up
Checks
- 1Confirm the real condition with a gauge or a second reading before replacing the DPF intake temperature
- 2Check that the DPF intake temperature circuit codes are not active, since a wiring fault can fake a high reading
- 3Look for the physical cause upstream, such as restriction, leakage, poor cooling or heavy load
- 4Compare it with the DOC outlet reading, which should be close when no heat is lost between them.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:DPF intake temperature - above normal - most severe
Cummins 3318DPF intake temperature: Erratic reading
The ECM judges the DPF intake temperature to be erratic or implausible: the value jumps, drifts or disagrees with related readings, which suggests a poor connection or a part on its way out. The DPF intake sensor sits at the filter inlet and protects the filter from over-temperature during regeneration.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent connector or wiring contact on the DPF intake temperature
- Part ageing or failing and giving unstable output
- Electrical noise from a poorly routed wire or a bad ground
Checks
- 1Watch the DPF intake temperature live in INSITE and wiggle the harness and connector to catch dropouts
- 2Compare the DPF intake temperature with a related reading to decide which one is wrong
- 3Check the connector for moisture and corrosion and the ground connection for tightness
- 4Compare it with the DOC outlet reading, which should be close when no heat is lost between them.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:DPF intake temperature - data erratic or incorrect
DPF outlet temperature5 codes
Cummins 3255DPF outlet temperature: Above normal· moderately severe
Same failure as 3311 on the DPF outlet temperature: the same fault condition as 3311, reported for this part. The DPF outlet sensor sits after the filter and shows the temperature leaving it, which matters most during regeneration.· Real conditionReal conditionCheck soonCauses
- Same causes as 3311, applied to the DPF outlet temperature
- Wiring or connector problem local to the DPF outlet temperature
Checks
- 1Compare it with the DPF intake reading during a regeneration to see how much heat the filter holds.
- 2Work through the checks listed for 3311, starting at the DPF outlet temperature and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:DPF outlet temperature - above normal - moderately severe
Cummins 3256DPF outlet temperature: Above normal· least severe
Same failure as 3311 on the DPF outlet temperature: the same fault condition as 3311, reported for this part. The DPF outlet sensor sits after the filter and shows the temperature leaving it, which matters most during regeneration.· Real conditionReal conditionInfoCauses
- Same causes as 3311, applied to the DPF outlet temperature
- Wiring or connector problem local to the DPF outlet temperature
Checks
- 1Compare it with the DPF intake reading during a regeneration to see how much heat the filter holds.
- 2Work through the checks listed for 3311, starting at the DPF outlet temperature and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:DPF outlet temperature - above normal - least severe
Cummins 3312DPF outlet temperature: Above normal· most severe
Same failure as 3311 on the DPF outlet temperature: the same fault condition as 3311, reported for this part. The DPF outlet sensor sits after the filter and shows the temperature leaving it, which matters most during regeneration.· Real conditionReal conditionStop nowCauses
- Same causes as 3311, applied to the DPF outlet temperature
- Wiring or connector problem local to the DPF outlet temperature
Checks
- 1Compare it with the DPF intake reading during a regeneration to see how much heat the filter holds.
- 2Work through the checks listed for 3311, starting at the DPF outlet temperature and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:DPF outlet temperature - above normal - most severe
Cummins 3322DPF outlet temperature: Erratic reading
Same failure as 3318 on the DPF outlet temperature: the same fault condition as 3318, reported for this part. The DPF outlet sensor sits after the filter and shows the temperature leaving it, which matters most during regeneration.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 3318, applied to the DPF outlet temperature
- Wiring or connector problem local to the DPF outlet temperature
Checks
- 1Compare it with the DPF intake reading during a regeneration to see how much heat the filter holds.
- 2Work through the checks listed for 3318, starting at the DPF outlet temperature and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:DPF outlet temperature - data erratic or incorrect
Cummins 7894DPF outlet temperature: Abnormal rate of change
The DPF outlet temperature changed faster than it physically could, so the ECM treats the reading as a sensor or wiring problem and not as a real change. The DPF outlet sensor sits after the filter and shows the temperature leaving it, which matters most during regeneration.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent contact in the harness or connector of the DPF outlet temperature
- Failing part giving unstable output
- Poor ground or noisy supply feeding the circuit
Checks
- 1Log the DPF outlet temperature while moving the harness and connector, and look for steps instead of smooth changes
- 2Inspect the DPF outlet temperature connector for water, corrosion and loose pins
- 3Check the supply and ground at the DPF outlet temperature while the engine runs
- 4Compare it with the DPF intake reading during a regeneration to see how much heat the filter holds.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
DOC intake temperature sensor circuit2 codes
Cummins 3313DOC intake temperature sensor circuit: Voltage low / shorted low
Same failure as 3316 on the DOC intake temperature sensor circuit: the same fault condition as 3316, reported for this part. The DOC intake sensor sits before the diesel oxidation catalyst and shows whether the exhaust is hot enough for the catalyst to light off.· Shorted lowShorted lowCheck soonCauses
- Same causes as 3316, applied to the DOC intake temperature sensor circuit
- Wiring or connector problem local to the DOC intake temperature sensor circuit
Checks
- 1Compare it with the DOC outlet reading on a warm engine: the outlet should be warmer only when the catalyst is working.
- 2Work through the checks listed for 3316, starting at the DOC intake temperature sensor circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:DOC intake temperature sensor circuit - voltage low (shorted to a low source)
Cummins 3314DOC intake temperature sensor circuit: Voltage high / shorted high
Same failure as 3317 on the DOC intake temperature sensor circuit: the same fault condition as 3317, reported for this part. The DOC intake sensor sits before the diesel oxidation catalyst and shows whether the exhaust is hot enough for the catalyst to light off.· Shorted highShorted highCheck soonCauses
- Same causes as 3317, applied to the DOC intake temperature sensor circuit
- Wiring or connector problem local to the DOC intake temperature sensor circuit
Checks
- 1Compare it with the DOC outlet reading on a warm engine: the outlet should be warmer only when the catalyst is working.
- 2Work through the checks listed for 3317, starting at the DOC intake temperature sensor circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:DOC intake temperature sensor circuit - voltage high (shorted to a high source)
DPF intake temperature sensor circuit2 codes
Cummins 3316DPF intake temperature sensor circuit: Voltage low / shorted low
The ECM reads the DPF intake temperature sensor circuit below its allowed voltage band. That points to a short to ground, an open supply or signal wire, or a failed part, not necessarily a real low value. The DPF intake sensor sits at the filter inlet and protects the filter from over-temperature during regeneration.· Shorted lowShorted lowCheck soonCauses
- Signal wire to the DPF intake temperature sensor circuit rubbed through and shorted to ground or to the engine block
- Open 5 V reference or open signal wire that lets the input drop to zero
- Corroded or backed-out pin in the DPF intake temperature sensor circuit connector
Checks
- 1Key on, unplug the DPF intake temperature sensor circuit and read its circuit at the harness: a reading near zero with the part removed means the wiring is shorted to ground or open
- 2Jumper the 5 V reference to the signal wire at the harness and see whether the code changes to a high-voltage code, which proves the wiring and the ECM input
- 3Measure resistance from the DPF intake temperature sensor circuit signal wire to ground with the ECM unplugged to find a short
- 4Compare it with the DOC outlet reading, which should be close when no heat is lost between them.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:DPF intake temperature sensor circuit - voltage low (shorted to a low source)
Cummins 3317DPF intake temperature sensor circuit: Voltage high / shorted high
The ECM reads the DPF intake temperature sensor circuit above its allowed voltage band. That points to a short to a 5 V or battery wire, a lost return, or a failed part, rather than a real change in what it measures. The DPF intake sensor sits at the filter inlet and protects the filter from over-temperature during regeneration.· Shorted highShorted highCheck soonCauses
- Short to a 5 V reference or a battery wire in the harness to the DPF intake temperature sensor circuit
- Open or high-resistance return wire that lets the signal float high
- Water or corrosion in the connector bridging two pins together
Checks
- 1Key on, unplug the DPF intake temperature sensor circuit and read its circuit at the harness: a high reading with the part removed means the wiring is shorted high or the return is lost
- 2Jumper the signal wire of the DPF intake temperature sensor circuit to ground at the harness and see whether the code changes to a low-voltage code, which proves the wiring and the ECM input
- 3Check continuity and resistance of the return wire from the DPF intake temperature sensor circuit back to the ECM
- 4Compare it with the DOC outlet reading, which should be close when no heat is lost between them.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:DPF intake temperature sensor circuit - voltage high (shorted to a high source)
DPF outlet temperature sensor circuit2 codes
Cummins 3319DPF outlet temperature sensor circuit: Voltage high / shorted high
Same failure as 3317 on the DPF outlet temperature sensor circuit: the same fault condition as 3317, reported for this part. The DPF outlet sensor sits after the filter and shows the temperature leaving it, which matters most during regeneration.· Shorted highShorted highCheck soonCauses
- Same causes as 3317, applied to the DPF outlet temperature sensor circuit
- Wiring or connector problem local to the DPF outlet temperature sensor circuit
Checks
- 1Compare it with the DPF intake reading during a regeneration to see how much heat the filter holds.
- 2Work through the checks listed for 3317, starting at the DPF outlet temperature sensor circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:DPF outlet temperature sensor circuit - voltage high (shorted to a high source)
Cummins 3321DPF outlet temperature sensor circuit: Voltage low / shorted low
Same failure as 3316 on the DPF outlet temperature sensor circuit: the same fault condition as 3316, reported for this part. The DPF outlet sensor sits after the filter and shows the temperature leaving it, which matters most during regeneration.· Shorted lowShorted lowCheck soonCauses
- Same causes as 3316, applied to the DPF outlet temperature sensor circuit
- Wiring or connector problem local to the DPF outlet temperature sensor circuit
Checks
- 1Compare it with the DPF intake reading during a regeneration to see how much heat the filter holds.
- 2Work through the checks listed for 3316, starting at the DPF outlet temperature sensor circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:DPF outlet temperature sensor circuit - voltage low (shorted to a low source)
DOC outlet gas temperature1 code
Cummins 3394DOC outlet gas temperature: Below normal· moderately severe
The DOC outlet gas temperature is below its normal range (severity: moderately severe). The ECM sets the code from a real reading, so look for a genuine cause before blaming the sensor. The DOC outlet sensor sits after the diesel oxidation catalyst and shows whether the catalyst is heating the exhaust during regeneration.· Real conditionReal conditionCheck soonCauses
- A real shortfall in the system the DOC outlet gas temperature measures
- Sensor or circuit reading low from a wiring fault
- A leak, low level or weak supply that lets the value fall
Checks
- 1Confirm the real condition with a gauge or a second reading before replacing the DOC outlet gas temperature
- 2Check that the DOC outlet gas temperature circuit codes are not active, since a wiring fault can fake a low reading
- 3Look for the physical cause upstream, such as a leak, low fluid, weak pump or blocked supply
- 4Compare it with the DOC intake reading during a regeneration to see whether the catalyst adds heat.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:DOC outlet gas temperature - below normal - moderately severe
DOC intake temperature sensor2 codes
Cummins 6779DOC intake temperature sensor: Reading drifted high
Same failure as 6784 on the DOC intake temperature sensor: the same fault condition as 6784, reported for this part. The DOC intake sensor sits before the diesel oxidation catalyst and shows whether the exhaust is hot enough for the catalyst to light off.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 6784, applied to the DOC intake temperature sensor
- Wiring or connector problem local to the DOC intake temperature sensor
Checks
- 1Compare it with the DOC outlet reading on a warm engine: the outlet should be warmer only when the catalyst is working.
- 2Work through the checks listed for 6784, starting at the DOC intake temperature sensor and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:DOC intake temperature sensor - data drifted high
Cummins 6781DOC intake temperature sensor: Reading drifted low
Same failure as 6785 on the DOC intake temperature sensor: the same fault condition as 6785, reported for this part. The DOC intake sensor sits before the diesel oxidation catalyst and shows whether the exhaust is hot enough for the catalyst to light off.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 6785, applied to the DOC intake temperature sensor
- Wiring or connector problem local to the DOC intake temperature sensor
Checks
- 1Compare it with the DOC outlet reading on a warm engine: the outlet should be warmer only when the catalyst is working.
- 2Work through the checks listed for 6785, starting at the DOC intake temperature sensor and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:DOC intake temperature sensor - data drifted low
DOC outlet gas temperature sensor2 codes
Cummins 6782DOC outlet gas temperature sensor: Reading drifted high
Same failure as 6784 on the DOC outlet gas temperature sensor: the same fault condition as 6784, reported for this part. The DOC outlet sensor sits after the diesel oxidation catalyst and shows whether the catalyst is heating the exhaust during regeneration.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 6784, applied to the DOC outlet gas temperature sensor
- Wiring or connector problem local to the DOC outlet gas temperature sensor
Checks
- 1Compare it with the DOC intake reading during a regeneration to see whether the catalyst adds heat.
- 2Work through the checks listed for 6784, starting at the DOC outlet gas temperature sensor and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:DOC outlet gas temperature sensor - data drifted high
Cummins 6783DOC outlet gas temperature sensor: Reading drifted low
Same failure as 6785 on the DOC outlet gas temperature sensor: the same fault condition as 6785, reported for this part. The DOC outlet sensor sits after the diesel oxidation catalyst and shows whether the catalyst is heating the exhaust during regeneration.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 6785, applied to the DOC outlet gas temperature sensor
- Wiring or connector problem local to the DOC outlet gas temperature sensor
Checks
- 1Compare it with the DOC intake reading during a regeneration to see whether the catalyst adds heat.
- 2Work through the checks listed for 6785, starting at the DOC outlet gas temperature sensor and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:DOC outlet gas temperature sensor - data drifted low
DPF outlet temperature sensor3 codes
Cummins 6784DPF outlet temperature sensor: Reading drifted high
The DPF outlet temperature sensor reads higher than the ECM calculates it should, and it has crept upward over time. That is typical of a sensor that is ageing or contaminated. The DPF outlet sensor sits after the filter and shows the temperature leaving it, which matters most during regeneration.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Sensing element ageing and reading high
- Sensor contaminated by soot, oil or deposits
- Slow rise in resistance in a connector or wire
Checks
- 1Compare the DPF outlet temperature sensor with a known good sensor or a reference gauge at the same operating point
- 2Clean or replace the DPF outlet temperature sensor if it is contaminated, and check its sensing port for blockage
- 3Measure the voltage drop in the wiring to the DPF outlet temperature sensor for extra resistance
- 4Compare it with the DPF intake reading during a regeneration to see how much heat the filter holds.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:DPF outlet temperature sensor - data drifted high
Cummins 6785DPF outlet temperature sensor: Reading drifted low
The DPF outlet temperature sensor reads lower than the ECM calculates it should, and it has crept downward over time. That is typical of a sensor that is ageing or leaking. The DPF outlet sensor sits after the filter and shows the temperature leaving it, which matters most during regeneration.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Sensing element ageing and reading low
- Sensor port blocked or leaking so it does not see the true value
- Slow rise in resistance in a connector or wire
Checks
- 1Compare the DPF outlet temperature sensor with a known good sensor or a reference gauge at the same operating point
- 2Inspect the DPF outlet temperature sensor sensing port and seals for blockage or leakage
- 3Measure the voltage drop in the wiring to the DPF outlet temperature sensor for extra resistance
- 4Compare it with the DPF intake reading during a regeneration to see how much heat the filter holds.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:DPF outlet temperature sensor - data drifted low
Cummins 6879DPF outlet temperature sensor: Reading drifted high
Same failure as 6784 on the DPF outlet temperature sensor: the same fault condition as 6784, reported for this part. The DPF outlet sensor sits after the filter and shows the temperature leaving it, which matters most during regeneration.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 6784, applied to the DPF outlet temperature sensor
- Wiring or connector problem local to the DPF outlet temperature sensor
Checks
- 1Compare it with the DPF intake reading during a regeneration to see how much heat the filter holds.
- 2Work through the checks listed for 6784, starting at the DPF outlet temperature sensor and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:DPF outlet temperature sensor - data drifted high
Shared checks
Checks, in order
- 1Read the DOC and DPF temperatures live with the engine cold: all four should match ambient and each other
- 2Unplug the suspect sensor and measure its resistance at ambient, then compare it with a good sensor of the same type
- 3Inspect the harness along the DOC and filter housing for burnt insulation and the connector for melted pins
- 4Compare the DOC outlet and DPF inlet readings on a warm engine: a large unexplained difference points to a sensor or a leak between them
- 5Check the regeneration and fuel doser codes so a real over-temperature is not missed
Causes
- Harness or connector burnt where it passes near the DOC or filter housing
- Failed thermistor reading out of range or drifting
- Real over-temperature from a failed regeneration, fuel in the exhaust or a blocked filter
- Fuel doser or DOC fault that stops the catalyst heating the exhaust as expected
Most common here: erratic or implausible (11 of 25)
Watch the live value on the service tool while you flex the harness and tap the connector.
When to stop
You'll notice: A regeneration inhibit or derate and a lamp; the engine runs normally otherwise.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
- Cummins ISB6.7 (2013-2018) Fault Code List (Diesel Repair)
- Cummins L9 (2024-2025) Fault Code List (Diesel Repair)
- Cummins L9 (2016-2020) Fault Code List (Diesel Repair)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
