Cummins · Operator controls
Cummins Brake, clutch, diagnostic and derate switches fault codes
The ECM watches the brake pedal position, the brake switch, the clutch switch and the parking brake switch. They cancel cruise control, check that brake and accelerator signals agree, and affect PTO operation and idle controls.
More about these partsLess
They normally come from the vehicle over the data link rather than being wired straight to the ECM. These switches let the operator or technician request a test mode, an auxiliary engine shutdown or override a shutdown. The engine derate switch and engine brake (retarder) selection tell the ECM what the driver wants.
Where to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
What do these codes mean?
Cummins codes 2718 to 15685 are all about the brake, clutch, diagnostic and derate switches. The most common failure type is erratic or implausible (8 of 20); none needs an immediate stop. Start with this check: read each switch and pedal value live while pressing and releasing it, and see whether the state follows the pedal.
How urgent are they?
None of the 20 codes here means stop now; 19 can wait until the shift ends, but find the cause before the next one; 1 is information only.
- Check soon19
- Info1
What should I check first?
Read each switch and pedal value live while pressing and releasing it, and see whether the state follows the pedal
Shared checks20 of 20
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Brake switch and accelerator pedal position incompatible1 code
Cummins 2718Brake switch and accelerator pedal position incompatible: Condition exists
The ECM has flagged a condition on the brake switch and accelerator pedal position incompatible. This is a status or result code that reports a state the control strategy found, rather than a failed wire. The ECM identified a persistent misfire on this one cylinder from crankshaft speed variation.· OtherOtherInfoCauses
- The underlying system problem that the ECM is reporting on the brake switch and accelerator pedal position incompatible
- A related sensor or circuit fault that triggered this condition
- Operating conditions outside what the strategy expects
Checks
- 1Read all active and inactive codes and work the circuit or sensor codes for the brake switch and accelerator pedal position incompatible first
- 2Check the live data around the brake switch and accelerator pedal position incompatible while reproducing the operating condition
- 3Inspect the system the brake switch and accelerator pedal position incompatible belongs to for leaks, blockage or damage
- 4Check compression, valve lash and the injector for this cylinder after ruling out fuel supply.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Brake pedal position3 codes
Cummins 4526Brake pedal position: Erratic reading
The ECM judges the brake pedal position to be erratic or implausible: the value jumps, drifts or disagrees with related readings, which suggests a poor connection or a part on its way out. The brake pedal position value reports how far the pedal is pressed and is normally sent by the vehicle brake controller.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent connector or wiring contact on the brake pedal position
- Part ageing or failing and giving unstable output
- Electrical noise from a poorly routed wire or a bad ground
Checks
- 1Watch the brake pedal position live in INSITE and wiggle the harness and connector to catch dropouts
- 2Compare the brake pedal position with a related reading to decide which one is wrong
- 3Check the connector for moisture and corrosion and the ground connection for tightness
- 4Press the brake pedal slowly and watch the position value rise smoothly from zero.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:Brake pedal position - data erratic or incorrect
Cummins 14335Brake pedal position: Out of calibration
The ECM reports the brake pedal position as out of calibration: the value or setting it received does not match what the ECM was programmed to expect. The brake pedal position value reports how far the pedal is pressed and is normally sent by the vehicle brake controller.· Part or controllerPart or controllerCheck soonCauses
- Parameter set for a feature that is not fitted on this vehicle
- Wrong or outdated calibration in the ECM
- Source module sending an invalid or unscaled value for the brake pedal position
Checks
- 1Compare the ECM parameters with the vehicle equipment, especially those that enable the brake pedal position
- 2Reflash the ECM with the correct calibration if the software level does not match
- 3Read the source module for its own codes and check its configuration
- 4Press the brake pedal slowly and watch the position value rise smoothly from zero.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Cummins 14336Brake pedal position: Abnormal update rate
The ECM is not receiving fresh data for the brake pedal position at the expected rate. The message is late or missing on the data link, or the sending module has stopped updating it. The brake pedal position value reports how far the pedal is pressed and is normally sent by the vehicle brake controller.· Lost messageLost messageCheck soonCauses
- Data link wiring fault or a poor connector contact
- The module that sends the message for the brake pedal position is offline or failing
- Power or ground problem at the sending module
Checks
- 1Look for other modules reporting timeouts to find where the link is broken
- 2Check the data link wiring, connectors and both terminators near the brake pedal position source
- 3Read the module that sends the brake pedal position for its own codes and for power or ground faults
- 4Press the brake pedal slowly and watch the position value rise smoothly from zero.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Parking brake switch2 codes
Cummins 11396Parking brake switch: Abnormal update rate
Same failure as 14336 on the parking brake switch: the same fault condition as 14336, reported for this part. The parking brake switch tells the ECM that the brake is applied, which affects PTO operation and idle controls.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 14336, applied to the parking brake switch
- Wiring or connector problem local to the parking brake switch
Checks
- 1Apply and release the parking brake and watch the switch state change in INSITE.
- 2Work through the checks listed for 14336, starting at the parking brake switch and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Cummins 11397Parking brake switch: Out of calibration
Same failure as 14335 on the parking brake switch: the same fault condition as 14335, reported for this part. The parking brake switch tells the ECM that the brake is applied, which affects PTO operation and idle controls.· Part or controllerPart or controllerCheck soonCauses
- Same causes as 14335, applied to the parking brake switch
- Wiring or connector problem local to the parking brake switch
Checks
- 1Apply and release the parking brake and watch the switch state change in INSITE.
- 2Work through the checks listed for 14335, starting at the parking brake switch and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Engine auxiliary shutdown switch2 codes
Cummins 14333Engine auxiliary shutdown switch: Out of calibration
Same failure as 14335 on the engine auxiliary shutdown switch: the same fault condition as 14335, reported for this part. The auxiliary shutdown switch lets another system or the driver request an engine shutdown.· Part or controllerPart or controllerCheck soonCauses
- Same causes as 14335, applied to the engine auxiliary shutdown switch
- Wiring or connector problem local to the engine auxiliary shutdown switch
Checks
- 1Operate the switch and confirm its state change and that the engine does not shut down unexpectedly.
- 2Work through the checks listed for 14335, starting at the engine auxiliary shutdown switch and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Cummins 14334Engine auxiliary shutdown switch: Abnormal update rate
Same failure as 14336 on the engine auxiliary shutdown switch: the same fault condition as 14336, reported for this part. The auxiliary shutdown switch lets another system or the driver request an engine shutdown.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 14336, applied to the engine auxiliary shutdown switch
- Wiring or connector problem local to the engine auxiliary shutdown switch
Checks
- 1Operate the switch and confirm its state change and that the engine does not shut down unexpectedly.
- 2Work through the checks listed for 14336, starting at the engine auxiliary shutdown switch and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Clutch switch2 codes
Cummins 14344Clutch switch: Out of calibration
Same failure as 14335 on the clutch switch: the same fault condition as 14335, reported for this part. The clutch switch tells the ECM that the clutch is pressed, which cancels cruise and allows engine speed to follow the driver.· Part or controllerPart or controllerCheck soonCauses
- Same causes as 14335, applied to the clutch switch
- Wiring or connector problem local to the clutch switch
Checks
- 1Press the clutch pedal slowly and watch the clutch switch state flip at the expected point.
- 2Work through the checks listed for 14335, starting at the clutch switch and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Cummins 14345Clutch switch: Abnormal update rate
Same failure as 14336 on the clutch switch: the same fault condition as 14336, reported for this part. The clutch switch tells the ECM that the clutch is pressed, which cancels cruise and allows engine speed to follow the driver.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 14336, applied to the clutch switch
- Wiring or connector problem local to the clutch switch
Checks
- 1Press the clutch pedal slowly and watch the clutch switch state flip at the expected point.
- 2Work through the checks listed for 14336, starting at the clutch switch and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Engine shutdown override switch2 codes
Cummins 14347Engine shutdown override switch: Out of calibration
Same failure as 14335 on the engine shutdown override switch: the same fault condition as 14335, reported for this part. The shutdown override switch lets the driver override a protection shutdown for a limited time.· Part or controllerPart or controllerCheck soonCauses
- Same causes as 14335, applied to the engine shutdown override switch
- Wiring or connector problem local to the engine shutdown override switch
Checks
- 1Operate the override switch and confirm the state change in INSITE.
- 2Work through the checks listed for 14335, starting at the engine shutdown override switch and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Cummins 14348Engine shutdown override switch: Abnormal update rate
Same failure as 14336 on the engine shutdown override switch: the same fault condition as 14336, reported for this part. The shutdown override switch lets the driver override a protection shutdown for a limited time.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 14336, applied to the engine shutdown override switch
- Wiring or connector problem local to the engine shutdown override switch
Checks
- 1Operate the override switch and confirm the state change in INSITE.
- 2Work through the checks listed for 14336, starting at the engine shutdown override switch and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Engine retarder selection2 codes
Cummins 14378Engine retarder selection: Out of calibration
Same failure as 14335 on the engine retarder selection: the same fault condition as 14335, reported for this part. The engine retarder selection tells the ECM which braking level the driver has chosen.· Part or controllerPart or controllerCheck soonCauses
- Same causes as 14335, applied to the engine retarder selection
- Wiring or connector problem local to the engine retarder selection
Checks
- 1Operate the retarder selector through each position and confirm the ECM state follows it.
- 2Work through the checks listed for 14335, starting at the engine retarder selection and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Cummins 14379Engine retarder selection: Abnormal update rate
Same failure as 14336 on the engine retarder selection: the same fault condition as 14336, reported for this part. The engine retarder selection tells the ECM which braking level the driver has chosen.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 14336, applied to the engine retarder selection
- Wiring or connector problem local to the engine retarder selection
Checks
- 1Operate the retarder selector through each position and confirm the ECM state follows it.
- 2Work through the checks listed for 14336, starting at the engine retarder selection and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Brake switch2 codes
Cummins 14381Brake switch: Out of calibration
Same failure as 14335 on the brake switch: the same fault condition as 14335, reported for this part. The brake switch tells the ECM that the driver is braking, so cruise cancels and brake lamps and torque limits can follow.· Lost messageLost messageCheck soonCauses
- Same causes as 14335, applied to the brake switch
- Wiring or connector problem local to the brake switch
Checks
- 1Press and release the brake pedal and watch the brake switch state flip with no delay.
- 2Work through the checks listed for 14335, starting at the brake switch and its connector
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Cummins 15685Brake switch: Abnormal update rate
Same failure as 14336 on the brake switch: the same fault condition as 14336, reported for this part. The brake switch tells the ECM that the driver is braking, so cruise cancels and brake lamps and torque limits can follow.· Lost messageLost messageCheck soonCauses
- Same causes as 14336, applied to the brake switch
- Wiring or connector problem local to the brake switch
Checks
- 1Press and release the brake pedal and watch the brake switch state flip with no delay.
- 2Work through the checks listed for 14336, starting at the brake switch and its connector
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Engine diagnostic test mode switch2 codes
Cummins 14382Engine diagnostic test mode switch: Out of calibration
Same failure as 14335 on the engine diagnostic test mode switch: the same fault condition as 14335, reported for this part. The diagnostic test mode switch lets a technician put the engine into a service test, so it should read off in normal driving.· Part or controllerPart or controllerCheck soonCauses
- Same causes as 14335, applied to the engine diagnostic test mode switch
- Wiring or connector problem local to the engine diagnostic test mode switch
Checks
- 1Check that the switch is released and its wiring is not shorted.
- 2Work through the checks listed for 14335, starting at the engine diagnostic test mode switch and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Cummins 14383Engine diagnostic test mode switch: Abnormal update rate
Same failure as 14336 on the engine diagnostic test mode switch: the same fault condition as 14336, reported for this part. The diagnostic test mode switch lets a technician put the engine into a service test, so it should read off in normal driving.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 14336, applied to the engine diagnostic test mode switch
- Wiring or connector problem local to the engine diagnostic test mode switch
Checks
- 1Check that the switch is released and its wiring is not shorted.
- 2Work through the checks listed for 14336, starting at the engine diagnostic test mode switch and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Engine derate switch2 codes
Cummins 14384Engine derate switch: Out of calibration
Same failure as 14335 on the engine derate switch: the same fault condition as 14335, reported for this part. The derate switch tells the ECM to limit engine power, for example when a vehicle system requests a reduction.· Part or controllerPart or controllerCheck soonCauses
- Same causes as 14335, applied to the engine derate switch
- Wiring or connector problem local to the engine derate switch
Checks
- 1Check the derate switch is released and confirm what vehicle system drives it.
- 2Work through the checks listed for 14335, starting at the engine derate switch and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Cummins 14385Engine derate switch: Abnormal update rate
Same failure as 14336 on the engine derate switch: the same fault condition as 14336, reported for this part. The derate switch tells the ECM to limit engine power, for example when a vehicle system requests a reduction.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 14336, applied to the engine derate switch
- Wiring or connector problem local to the engine derate switch
Checks
- 1Check the derate switch is released and confirm what vehicle system drives it.
- 2Work through the checks listed for 14336, starting at the engine derate switch and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Shared checks
Checks, in order
- 1Read each switch and pedal value live while pressing and releasing it, and see whether the state follows the pedal
- 2Operate the diagnostic test mode, auxiliary shutdown and override switches one at a time and watch each state in INSITE
- 3Move the engine brake selector through every position and watch the selection value in INSITE
- 4Check the switch adjustment, mounting and plunger travel at the pedal or lever
- 5Check whether the auxiliary shutdown and shutdown override features are enabled in the ECM parameters
- 6Check that the engine brake option and its levels are enabled in the ECM parameters
- 7Inspect the connector and harness at the switch for corrosion and damage
Causes
- Switch out of adjustment, worn or stuck
- Test-mode or shutdown switch contacts stuck or worn
- Engine brake level selector worn or its contacts dirty
- Wiring or connector fault between the switch and the module that sends the message
Most common here: erratic or implausible (8 of 20)
Watch the live value on the service tool while you flex the harness and tap the connector.
When to stop
You'll notice: Cruise control or PTO that will not engage or cancels at random, brake lamp or idle behaviour that does not match what the driver does, and a logged code.
Brake and steering faults are a safety issue on site. Chock the machine and keep it parked until the fault is found and the brakes are tested.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Cummins L9 (2024-2025) Fault Code List (Diesel Repair)
- Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
