Cummins · Cooling - SPN 110 FMI 4
Cummins Fault Code 145
Engine coolant temperature sensor signal voltage low
What does Cummins code 145 mean?
The ECM sees the engine coolant temperature sensor signal as extremely hot or shorted. On a two-wire thermistor that means a signal wire shorted to ground or a failed sensor. Urgency: check soon - the machine may derate or limit a function. Check first: cold engine key on: a coolant reading far above anything a cold engine can reach means the circuit is shorted.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Cold engine key on: a coolant reading far above anything a cold engine can reach means the circuit is shorted
Then 4 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 5 done
Causes
- Coolant temperature sensor wire shorted to the thermostat housing or a bracket
- Coolant wicking up the sensor wires and bridging the terminals
- Thermistor inside the sensor failed shorted
- Harness hardened by heat near the thermostat housing and cracked to ground
How it failed
You'll notice: The fan may run all the time, cold starts may be rough and the temperature gauge may read wrong.
Shorted lowRead from how the source describes the code
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Coolant temperature, oil temperature and oil pressure
2 other codes on this part are also shorted low (141, 213). When they show together, start at the wiring and connector they share.
- 135Engine oil rifle pressure 1 sensor circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 141Engine oil pressure sensor signal voltage lowShorted lowCheck soon
- 143Engine oil pressure low - moderately severeOtherCheck soon
- 144Engine coolant temperature sensor signal voltage highShorted highCheck soon
- 145Engine coolant temperature sensor signal voltage lowShorted lowCheck soon
- 146Engine coolant temperature high - moderately severeOtherCheck soon
- 151Engine coolant temperature high - most severeOtherStop now
- 212Engine oil temperature sensor 1 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 213Engine oil temperature sensor 1 circuit - voltage low (shorted to a low source)Shorted lowCheck soon
Show the other 11 codesHide the other codes
- 214Engine oil temperature too high - most severeLost messageStop now
- 334Coolant temperature - data erraticErratic or implausibleCheck soon
- 415Engine oil pressure low - most severeLost messageStop now
- 421Engine oil temperature - above normal - moderately severeReal conditionCheck soon
- 425Engine oil temperature - data erratic or incorrectErratic or implausibleCheck soon
- 435Oil pressure sensor - data erraticErratic or implausibleCheck soon
- 2646Engine coolant temperature - condition existsOtherInformation
- 2659Engine coolant temperature - condition existsOtherInformation
- 2789Engine coolant temperature too lowReal conditionInformation
- 2963Engine coolant temperature high - least severeOtherCheck soon
- 3243Engine cooling system monitor - below normal - moderately severeReal conditionCheck soon
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 145 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/ISB6.7/B6.7/L9 engines (J1939 SPN 110, FMI 4); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
