Cummins · Cooling - SPN 110 FMI 3
Cummins Fault Code 144
Engine coolant temperature sensor signal voltage high
What does Cummins code 144 mean?
The ECM sees the engine coolant temperature sensor signal as very cold or open. On a two-wire thermistor that is an open circuit, an unplugged sensor or a failed sensor. Urgency: check soon - the machine may derate or limit a function. Check first: cold engine key on: a reading far below ambient or at the lowest end of the scale means the circuit is open.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Cold engine key on: a reading far below ambient or at the lowest end of the scale means the circuit is open
Then 4 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 5 done
Causes
- Coolant temperature sensor connector unplugged or loose at the thermostat housing
- Sensor wire broken inside the insulation near the thermostat housing
- Thermistor inside the sensor failed open
- Corrosion in the connector raising the circuit resistance
How it failed
You'll notice: The fan may run all the time, cold starts may be rough and the temperature gauge may read wrong.
Shorted highRead from how the source describes the code
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Coolant temperature, oil temperature and oil pressure
2 other codes on this part are also shorted high (135, 212). When they show together, start at the wiring and connector they share.
- 135Engine oil rifle pressure 1 sensor circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 141Engine oil pressure sensor signal voltage lowShorted lowCheck soon
- 143Engine oil pressure low - moderately severeOtherCheck soon
- 144Engine coolant temperature sensor signal voltage highShorted highCheck soon
- 145Engine coolant temperature sensor signal voltage lowShorted lowCheck soon
- 146Engine coolant temperature high - moderately severeOtherCheck soon
- 151Engine coolant temperature high - most severeOtherStop now
- 212Engine oil temperature sensor 1 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 213Engine oil temperature sensor 1 circuit - voltage low (shorted to a low source)Shorted lowCheck soon
Show the other 11 codesHide the other codes
- 214Engine oil temperature too high - most severeLost messageStop now
- 334Coolant temperature - data erraticErratic or implausibleCheck soon
- 415Engine oil pressure low - most severeLost messageStop now
- 421Engine oil temperature - above normal - moderately severeReal conditionCheck soon
- 425Engine oil temperature - data erratic or incorrectErratic or implausibleCheck soon
- 435Oil pressure sensor - data erraticErratic or implausibleCheck soon
- 2646Engine coolant temperature - condition existsOtherInformation
- 2659Engine coolant temperature - condition existsOtherInformation
- 2789Engine coolant temperature too lowReal conditionInformation
- 2963Engine coolant temperature high - least severeOtherCheck soon
- 3243Engine cooling system monitor - below normal - moderately severeReal conditionCheck soon
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 144 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/ISB6.7/B6.7/L9 engines (J1939 SPN 110, FMI 3); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
