Cummins · Aftertreatment - SPN 3251 FMI 3
Cummins Fault Code 1879
DPF differential pressure sensor signal voltage high
What does Cummins code 1879 mean?
The ECM sees the DPF differential pressure sensor signal above its normal voltage band. Urgency: check soon - the machine may derate or limit a function. Check first: key on, engine off: differential pressure should read near zero; a high reading confirms the sensor circuit.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Key on, engine off: differential pressure should read near zero; a high reading confirms the sensor circuit
Then 4 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 5 done
Causes
- DPF pressure sensor signal shorted to the reference line in the harness
- Open return wire at the sensor connector
- Differential pressure sensor failed high after water or soot got in
- Pressure hoses swapped on the sensor ports giving a high reading
How it failed
You'll notice: The diesel particulate filter cannot be monitored properly.
Shorted highRead from how the source describes the code
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: DPF pressure sensors and DPF system
1 other code on this part is also shorted high (3133). When they show together, start at the wiring and connector they share.
- 1879DPF differential pressure sensor signal voltage highShorted highCheck soon
- 1881DPF differential pressure sensor signal voltage lowShorted lowCheck soon
- 1883DPF differential pressure - data erratic or incorrectErratic or implausibleCheck soon
- 1921DPF differential pressure high - moderately severeOtherCheck soon
- 1922DPF differential pressure high - most severeOtherStop now
- 1981DPF system - above normal - least severeReal conditionInformation
- 1993Aftertreatment diesel particulate filter missingOtherStop now
- 2639DPF differential pressure high - least severeOtherInformation
- 2692DPF system - data erratic or incorrectErratic or implausibleCheck soon
Show the other 11 codesHide the other codes
- 2754Engine DPF intake pressure - above normal - moderately severeReal conditionCheck soon
- 3133DPF outlet pressure sensor circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 3134DPF outlet pressure sensor circuit - voltage low (shorted to a low source)Shorted lowCheck soon
- 3135DPF outlet pressure - data erratic or incorrectErratic or implausibleCheck soon
- 3168DPF system - above normal - moderately severeReal conditionCheck soon
- 3245DPF system - mechanical fault or not respondingPart or controllerCheck soon
- 4584DPF system - special instructionsOtherInformation
- 5715DPF differential pressure - abnormal rate of changeErratic or implausibleCheck soon
- 5716DPF outlet pressure - abnormal rate of changeErratic or implausibleCheck soon
- 6265DPF system - mechanical fault or not respondingPart or controllerCheck soon
- 6786DPF outlet pressure sensor - data drifted highErratic or implausibleCheck soon
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 1879 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/ISB6.7/B6.7/L9 engines (J1939 SPN 3251, FMI 3); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
