Cummins · Engine control module - SPN 629 FMI 12
Cummins Fault Code 111
Engine control module - critical internal failure
What does Cummins code 111 mean?
The engine control module has detected a critical failure inside itself. The ECM may reset, lose control of the injectors or shut the engine down. Urgency: stop now - shut down and fix before working on. Check first: read the code with INSITE and note whether it is active or only stored.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Read the code with INSITE and note whether it is active or only stored
Then 4 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 5 done
Causes
- Internal ECM failure
- Power or ground supply to the ECM unstable
- Water or corrosion in the ECM connectors
- Wrong or corrupt calibration
How it failed
You'll notice: The red stop lamp may come on, the engine may stall, or it may not start at all.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Sensor supply circuits and ECM internal faults
- 111Engine control module - critical internal failureOtherStop now
- 187Sensor supply 2 circuit - voltage low (shorted to a low source)Shorted lowCheck soon
- 227Sensor supply 2 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 238Sensor supply 3 circuit - voltage low (shorted to a low source)Shorted lowCheck soon
- 239Sensor supply 3 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 319Real-time clock power interrupt - data erratic or incorrectErratic or implausibleCheck soon
- 343Engine control module - warning internal hardware failureOtherCheck soon
- 346Engine control module calibration memory software - bad device or componentPart or controllerCheck soon
- 352Sensor supply 1 circuit - voltage low (shorted to a low source)Shorted lowCheck soon
Show the other 15 codesHide the other codes
- 386Sensor supply 1 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 515Sensor supply 6 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 516Sensor supply 6 circuit - voltage low (shorted to a low source)Shorted lowCheck soon
- 1695Sensor supply 5 - voltage high (shorted to a high source)Shorted highCheck soon
- 1696Sensor supply 5 - voltage low (shorted to a low source)Shorted lowCheck soon
- 2185Sensor supply 4 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 2186Sensor supply 4 circuit - voltage low (shorted to a low source)Shorted lowCheck soon
- 2416Engine control module calibration memory checksum - out of calibrationPart or controllerCheck soon
- 3492Real-time clock - abnormal rate of changeErratic or implausibleCheck soon
- 3656Real-time clock - out of calibrationPart or controllerCheck soon
- 3697Engine control module calibration memory - bad device or componentLost messageCheck soon
- 5874Engine control module calibration memory (rom) corruption - root cause not knownPart or controllerInformation
- 6155Engine control module - root cause not knownOtherInformation
- 8195Datalog memory card - bad device or componentPart or controllerCheck soon
- 8196Datalog memory card - root cause not knownPart or controllerInformation
Other Cummins codes: Engine control module - SPN 629 FMI 12
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 111 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/ISB6.7/B6.7/L9 engines (J1939 SPN 629, FMI 12); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
