Cummins · Fuel system - SPN 651 FMI 5
Cummins Fault Code 322
Injector solenoid circuit, cylinder 1 open circuit
What does Cummins code 322 mean?
The ECM finds no current flowing in the injector solenoid circuit, cylinder 1 circuit when it commands it on, so the circuit is open or the load is unplugged. Cylinder 1 injector circuit. Urgency: check soon - the machine may derate or limit a function. Check first: run the cylinder cut-out test in INSITE and see whether cylinder 1 makes any contribution.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Run the cylinder cut-out test in INSITE and see whether cylinder 1 makes any contribution
Then 4 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 5 done
Causes
- Injector solenoid coil open on cylinder 1
- Injector connector under the valve cover loose
- Harness wire broken at the cylinder 1 injector
- Oil-soaked harness insulation failing
How it failed
You'll notice: The cylinder does not fire correctly, so the engine runs rough, may smoke and may be derated.
Open circuitRead from how the source describes the code
No current flows, or the signal floats - a wire, pin or coil is broken.
- Meter test
- Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
- Good result
- Near 0 Ω on each wire. The part reads its listed resistance, not OL.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Injector solenoid circuits (cylinders 1 to 6)
5 other codes on this part are also open circuit (323, 324, 325, 331 and more). When they show together, start at the wiring and connector they share.
- 322Injector solenoid circuit, cylinder 1 open circuitOpen circuitCheck soon
- 323Injector solenoid driver cylinder 5 circuit - current low or open circuitOpen circuitCheck soon
- 324Injector solenoid driver cylinder 3 circuit - current low or open circuitOpen circuitCheck soon
- 325Injector solenoid driver cylinder 6 circuit - current low or open circuitOpen circuitCheck soon
- 331Injector solenoid driver cylinder 2 circuit - current low or open circuitOpen circuitCheck soon
- 332Injector solenoid driver cylinder 4 circuit - current low or open circuitOpen circuitCheck soon
- 1139Injector solenoid driver cylinder 1 - mechanical faultOtherCheck soon
- 1141Injector solenoid driver cylinder 2 - mechanical fault or not respondingPart or controllerCheck soon
- 1142Injector solenoid driver cylinder 3 - mechanical fault or not respondingPart or controllerCheck soon
Show the other 3 codesHide the other codes
- 1143Injector solenoid driver cylinder 4 - mechanical fault or not respondingPart or controllerCheck soon
- 1144Injector solenoid driver cylinder 5 - mechanical fault or not respondingPart or controllerCheck soon
- 1145Injector solenoid driver cylinder 6 - mechanical fault or not respondingPart or controllerCheck soon
Other Cummins codes: Fuel system - SPN 651 FMI 5
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 322 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/ISB6.7/B6.7/L9 engines (J1939 SPN 651, FMI 5); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
