Cummins · Air handling - SPN 102 FMI 3
Cummins Fault Code 122
Intake manifold pressure sensor signal voltage high
What does Cummins code 122 mean?
The ECM sees the intake manifold pressure sensor signal above its normal voltage band. Urgency: check soon - the machine may derate or limit a function. Check first: key on, engine off: manifold pressure should match barometric pressure; a reading near the top of its scale confirms a high-voltage fault.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Key on, engine off: manifold pressure should match barometric pressure; a reading near the top of its scale confirms a high-voltage fault
Then 4 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 5 done
Causes
- Sensor signal wire rubbed through against the intake manifold bracket and touching the 5 V reference
- Open return wire between the boost sensor and the ECM, so the signal climbs to reference
- Pressure sensor failed high internally after oil or moisture got into the port
- Connector shared by the intake temperature element corroded, lifting the signal
How it failed
You'll notice: The engine runs on a fixed boost map, so it feels flat under load, smokes more and may be limited in power.
Shorted highRead from how the source describes the code
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Intake manifold pressure and temperature sensors
1 other code on this part is also shorted high (153). When they show together, start at the wiring and connector they share.
- 122Intake manifold pressure sensor signal voltage highShorted highCheck soon
- 123Intake manifold pressure sensor signal voltage lowShorted lowCheck soon
- 124Intake manifold pressure high - moderately severeOtherCheck soon
- 125Intake manifold pressure low - moderately severeOtherCheck soon
- 153Intake manifold temperature sensor signal voltage highShorted highCheck soon
- 154Intake manifold temperature sensor signal voltage lowShorted lowCheck soon
- 155Intake manifold 1 temperature - above normal - most severeReal conditionStop now
- 436Intake manifold 1 temperature - data erratic or incorrectErratic or implausibleCheck soon
- 488Intake manifold 1 temperature - above normal - moderately severeReal conditionCheck soon
Show the other 14 codesHide the other codes
- 1848Intake manifold 1 temperature - abnormal rate of changeErratic or implausibleCheck soon
- 2191Intake manifold 1 pressure sensor - condition existsOtherInformation
- 2964Intake manifold temperature high - least severeOtherCheck soon
- 2973Intake manifold pressure sensor data erratic or implausibleErratic or implausibleCheck soon
- 3361Intake manifold 1 pressure - abnormal rate of changeErratic or implausibleCheck soon
- 3385Intake manifold 1 temperature - below normal - moderately severeReal conditionCheck soon
- 4616Intake manifold 1 pressure - below normal - least severeReal conditionInformation
- 4729Intake manifold 1 pressure - below normal - most severeReal conditionStop now
- 5989Intake manifold 1 pressure - data drifted highErratic or implausibleCheck soon
- 5991Intake manifold 1 pressure - data drifted lowErratic or implausibleCheck soon
- 6725Intake manifold 1 pressure - above normal - least severeReal conditionInformation
- 6864Intake manifold 1 pressure - below normal - least severeReal conditionInformation
- 7233Engine intake manifold pressure - below normal - most severeReal conditionStop now
- 7583Intake manifold 1 pressure - above normal - least severeReal conditionInformation
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 122 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/ISB6.7/B6.7/L9 engines (J1939 SPN 102, FMI 3); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
