Cummins · Air handling - SPN 102 FMI 2
Cummins Fault Code 2973
Intake manifold pressure sensor data erratic or implausible
What does Cummins code 2973 mean?
The ECM does not trust the intake manifold pressure sensor reading because it drifts, jumps or disagrees with other sensors. The circuit tests inside limits, so the fault is usually intermittent or the sensor is out of step with reality. Urgency: check soon - the machine may derate or limit a function. Check first: compare manifold pressure with barometric pressure at key on and with the engine running at idle.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Compare manifold pressure with barometric pressure at key on and with the engine running at idle
Then 4 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 5 done
Causes
- Boost leak after the charge-air cooler making the manifold pressure disagree with demand
- Boost sensor port blocked with soot or oil so the sensor reads a stale value
- Turbo actuator sticking, so real boost is wrong while the sensor is right
- Connector pin making contact only part of the time
How it failed
You'll notice: The engine runs on a fixed boost map, so it feels flat under load, smokes more and may be limited in power.
Erratic or implausibleRead from how the source describes the code
The reading jumps, drifts or disagrees with the sensors around it.
- Meter test
- Watch the live value on the service tool while you flex the harness and tap the connector.
- Good result
- A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Intake manifold pressure and temperature sensors
5 other codes on this part are also erratic or implausible (436, 1848, 3361, 5989 and more). When they show together, start at the wiring and connector they share.
- 488Intake manifold 1 temperature - above normal - moderately severeReal conditionCheck soon
- 1848Intake manifold 1 temperature - abnormal rate of changeErratic or implausibleCheck soon
- 2191Intake manifold 1 pressure sensor - condition existsOtherInformation
- 2964Intake manifold temperature high - least severeOtherCheck soon
- 2973Intake manifold pressure sensor data erratic or implausibleErratic or implausibleCheck soon
- 3361Intake manifold 1 pressure - abnormal rate of changeErratic or implausibleCheck soon
- 3385Intake manifold 1 temperature - below normal - moderately severeReal conditionCheck soon
- 4616Intake manifold 1 pressure - below normal - least severeReal conditionInformation
- 4729Intake manifold 1 pressure - below normal - most severeReal conditionStop now
Show the other 14 codesHide the other codes
- 122Intake manifold pressure sensor signal voltage highShorted highCheck soon
- 123Intake manifold pressure sensor signal voltage lowShorted lowCheck soon
- 124Intake manifold pressure high - moderately severeOtherCheck soon
- 125Intake manifold pressure low - moderately severeOtherCheck soon
- 153Intake manifold temperature sensor signal voltage highShorted highCheck soon
- 154Intake manifold temperature sensor signal voltage lowShorted lowCheck soon
- 155Intake manifold 1 temperature - above normal - most severeReal conditionStop now
- 436Intake manifold 1 temperature - data erratic or incorrectErratic or implausibleCheck soon
- 5989Intake manifold 1 pressure - data drifted highErratic or implausibleCheck soon
- 5991Intake manifold 1 pressure - data drifted lowErratic or implausibleCheck soon
- 6725Intake manifold 1 pressure - above normal - least severeReal conditionInformation
- 6864Intake manifold 1 pressure - below normal - least severeReal conditionInformation
- 7233Engine intake manifold pressure - below normal - most severeReal conditionStop now
- 7583Intake manifold 1 pressure - above normal - least severeReal conditionInformation
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 2973 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/ISB6.7/B6.7/L9 engines (J1939 SPN 102, FMI 2); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
