Komatsu error codes
Komatsu excavators show a user code such as E02 on the monitor and log a service code such as CA234 or DXA8KA behind it. These are the PC200-8-era codes and the older PC200-6/7 service codes.
153 codes in 17 families8 stop now, 137 check soon, 8 info
153 Komatsu codes - type a code, or a word from the problem.
Covers Excavators.
Where to look
- 01Watch the monitor for the user code and the caution lamp or buzzer, and write the…
- 02Switch the monitor to service mode with the key and function buttons described in the…
- 03Read the failure codes shown there, for example CA115 or DXA8KA.
- 04Fix the cause, clear the fault history in service mode, then start the engine and…
How to read Komatsu error codes, in full
- Watch the monitor for the user code and the caution lamp or buzzer, and write the code down.
- Switch the monitor to service mode with the key and function buttons described in the operator's manual and open the fault history.
- Read the failure codes shown there, for example CA115 or DXA8KA; the first letters tell the controller: CA is engine, D is machine and pump controller.
- Fix the cause, clear the fault history in service mode, then start the engine and confirm the code does not return.
How urgent is a Komatsu code?
- Stop now8 codes
- Shut down and fix before working on. Running on risks damage or the machine locks out.
- Check soon137 codes
- The machine may derate or limit a function. Find the cause before the next shift.
- Information8 codes
- A reminder or status message. Nothing is failing yet.
Pick your system
Find the part of the machine, then the family your code belongs to.
- Code range
- The first and last code in the family, as the machine shows them.
- Codes
- How many codes the family holds; each is explained on its page.
- Severity mix
- The share of stop, check and info codes. The dot after it is the most urgent one in the family.
Engine controller62 codes
- Engine Ne and backup speed sensorsCA115 – CA7785 codes
- Engine sensor 5 V suppliesDA25KP – CA3865 codes
- Throttle sensor and its supplyCA131 – CA21864 codes
- Boost, intake air, coolant and ambient sensorsCA122 – CA48810 codes
- Common rail fuel pressureCA449 – CA22496 codes
- Injector and IMV solenoid circuitsCA271 – CA231111 codes
- Engine controller internal and network faultsCA111 – CA16336 codes
- Engine fluid, filter and temperature warningsB@BAZG – CA4359 codes
- Battery, charging and air heaterAB00KE – CA25565 codes
- Engine overspeedCA234Stop now
Pump controller41 codes
- Pump, PPC, load and oil temperature sensorsDHPAMA – DHS8MA10 codes
- Pump PC-EPC, LS-EPC and flow divider solenoidsDXE0KA – DA22KK13 codes
- Travel speed, swing brake and relief solenoidsDWK0KA – DW91KB10 codes
- Controller network, option and GPS codesDA2RMC – D862KA4 codes
- Wiper and washer circuitsDY2CKA – DY20MA4 codes
Monitor user codes8 codes
Monitor service codes42 codes
Most searched Komatsu codes
- B@BAZGEngine oil pressure low
- B@BCNSEngine coolant overheating
- DHPAMAFront pump pressure sensor abnormal
- AB00KECharging voltage low
- E0ENetwork (data link) failure
- DA2RMCCAN circuit break (pump controller connection)
- E02PC-EPC system
- E03Swing parking brake system
- DXA8KAPC-EPC (front pump) solenoid: circuit open
- DW43KATravel speed solenoid: circuit open
- CA111Engine controller critical internal error
- CA115Engine Ne and Bkup speed sensor error
- CA234Engine overspeed
- CA322Injector #1 (L#1) open or short circuit
- CA428Water in fuel sensor: high voltage
- CA441Battery voltage low
- CA449Common rail pressure too high (stage 2)
- CA559Common rail pressure too low (stage 1)
- CA689Engine Ne speed sensor error
- CA1633KOMNET data link timeout
- CA2185Throttle sensor power supply: high voltage
- CA2186Throttle sensor power supply: low voltage
Quick answers
How do I read Komatsu error codes?
Watch the monitor for the user code and the caution lamp or buzzer, and write the code down. Switch the monitor to service mode with the key and function buttons described in the operator's manual and open the fault history.
Which Komatsu codes mean stop now?
8 of the 153 Komatsu codes listed are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. For example B@BAZG, B@BCNS, CA111, CA115. 137 are Check soon. The machine may derate or limit a function. Find the cause before the next shift.
What should I check first on a Komatsu code?
Most Komatsu codes here (25 of 153) read as open circuit: no current flows, or the signal floats - a wire, pin or coil is broken. First test, as general workshop practice: key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Sources
Every code was read from these documents and written in our own words.
Other makers
Machine down? Post a request for a replacement machine or a technician; suppliers in the UAE contact you.
Post a request