EF Logo

Komatsu · Engine controller

Komatsu Engine fluid, filter and temperature warnings fault codes

These monitor warnings come from engine and hydraulic sensors: air filter restriction, engine oil pressure and level, coolant temperature and level, hydraulic oil temperature, oil pressure switch and the water-in-fuel sensor. The monitor tells the operator to stop or fix the problem soon.

FaultStopB@BAZGKomatsu · Engine fluid, filter and temperature warnings
Code shows hereFAULTB@BAZG

Where this code shows

Watch the monitor for the user code and the caution lamp or buzzer, and write the code down.

What do these codes mean?

Komatsu codes B@BAZG to CA435 are all about the engine fluid, filter and temperature warnings. The most common failure type is shorted high (3 of 9); 3 need an immediate stop. Start with this check: check the real condition first: oil level, coolant level, filter state and temperature by gauge.

How urgent are they?

3 of 9 codes here mean stop now; the other 6 can wait until the shift ends, but find the cause before the next one.

  • Stop now3
  • Check soon6

What should I check first?

Check the real condition first: oil level, coolant level, filter state and temperature by gauge

Shared checks

9 of 9

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Komatsu B@BAZGEngine oil pressure low

    The engine oil pressure is below the allowed value for the speed.· Other
    Stop now

    Causes

    • Low engine oil level
    • Worn oil pump or bearings
    • Clogged oil filter
    • Failed oil pressure switch or wiring

    Checks

    1. 1Stop the engine and check the oil level and filter condition
    2. 2Fit a mechanical gauge at the test point to confirm real pressure before replacing the switch
    3. 3Check the oil pressure switch connector and its wiring for oil and breaks
    4. 4Look for fuel dilution or foaming oil on the dipstick
    5. 5If real pressure is low with good oil, inspect the oil pump and bearings
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Komatsu B@BAZKEngine oil level low

    The oil level switch reports the engine oil level below the lower limit.· Other
    Check soon

    Causes

    • Oil level genuinely low from a leak or consumption
    • Oil level sensor connector loose
    • Failed level sensor

    Checks

    1. 1Check the dipstick level on level ground and top up
    2. 2Check for leaks around the pan, gasket and turbocharger lines
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Komatsu B@BCNSEngine coolant overheating

    The engine coolant temperature went above the limit.· Shorted high
    Stop now

    Causes

    • Low coolant level or leak
    • Blocked radiator or oil cooler fins
    • Fan drive or belt not working
    • Failed thermostat
    • Failed temperature sensor

    Checks

    1. 1Let the engine idle to cool, then check the coolant level when it is safe to do so
    2. 2Clean the radiator and cooler fins and check the fan belt and fan speed
    3. 3Check that the thermostat opens at its rated temperature
    4. 4Compare the monitor temperature with an infrared thermometer
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Komatsu B@BCZKEngine coolant level low

    The coolant level sensor reports the level below the lower limit.· Lost message
    Check soon

    Causes

    • Coolant leak at hoses, radiator or water pump
    • Coolant not topped up after service
    • Level sensor fault

    Checks

    1. 1Check the coolant level in the radiator and reserve tank when cold
    2. 2Look for leaks at hoses, radiator, water pump and heater lines
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Komatsu B@HANSHydraulic oil overheating

    The hydraulic oil temperature went above the limit.· Shorted high
    Stop now

    Causes

    • Blocked oil cooler or radiator
    • Fan not running correctly
    • Hydraulic relief valve opening continuously
    • Failed oil temperature sensor

    Checks

    1. 1Clean the oil cooler and check the fan operation
    2. 2Check for a work pattern that keeps the machine at relief, such as holding a cylinder at end of stroke
    3. 3Compare the monitor temperature with a trusted thermometer
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Komatsu AA10NXAir filter clogged

    The air cleaner restriction switch reports a clogged filter element.· Real condition
    Check soon

    Causes

    • Dirty or oil-soaked air filter element
    • Dust pre-cleaner blocked
    • Restriction switch or wiring fault

    Checks

    1. 1Inspect and clean or replace the air filter element following the maintenance schedule
    2. 2Check the restriction switch connector and wiring
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Komatsu CA428Water in fuel sensor: high voltage

    The water-in-fuel sensor in the fuel separator is reporting a voltage above range.· Shorted high
    Check soon

    Causes

    • Water collected in the fuel separator bowl
    • Water sensor wire open or loose
    • Sensor failed
    • Contaminated fuel from the tank

    Checks

    1. 1Drain the water from the fuel separator and see whether the code clears
    2. 2Check the water sensor connector and wiring for corrosion and open wires
    3. 3Inspect the fuel tank bottom for water and sediment
    4. 4Replace the fuel filters if water has been present, then clear the code
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Komatsu CA429Water in fuel sensor: low voltage

    The water-in-fuel sensor signal is below range.· Shorted low
    Check soon

    Causes

    • Sensor wire shorted to ground
    • Failed water sensor

    Checks

    1. 1Unplug the water sensor and measure the signal wire to ground
    2. 2Replace the sensor if the wiring is good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Komatsu CA435Engine oil pressure switch error

    The engine oil pressure switch signal does not match the engine state.· Other
    Check soon

    Causes

    • Failed oil pressure switch
    • Switch wire open or shorted
    • Real low oil pressure

    Checks

    1. 1Fit a mechanical gauge to confirm oil pressure
    2. 2Check the oil pressure switch connector and its wiring for oil and breaks
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Check the real condition first: oil level, coolant level, filter state and temperature by gauge
  2. 2Inspect the sensor connector for oil and corrosion
  3. 3Compare the monitor reading with a trusted gauge or thermometer
  4. 4Look for leaks on the ground and engine that explain a low level
  5. 5Clear the code and see whether it returns once the real condition is corrected

Causes

  • Low fluid level or dirty filter that the sensor is correctly reporting
  • Loose or oily sensor connector
  • Failed sensor or switch
  • Blocked radiator, oil cooler or fan problems for temperature warnings

Most common here: shorted high (3 of 9)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: The monitor shows the warning symbol and a failure code, and the buzzer may sound.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.