Thermo King · Engine ECU faults (SR-2/SR-3/SR-4)
Thermo King Fault Code 600
Check crankshaft speed sensor
What does Thermo King code 600 mean?
The engine ECU is not getting a usable crankshaft speed signal, so it cannot time the injection or know the engine speed. Urgency: stop now - shut down and fix before working on. Check first: inspect the crankshaft sensor plug and wires for chafing near the block.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Inspect the crankshaft sensor plug and wires for chafing near the block
Then 4 more checksWhere this code shows
Press the alarm key or open the Alarms menu on the controller display to list active alarms.
Checks
0 of 5 done
Causes
- Crankshaft sensor connector loose or corroded
- Sensor wire chafed against the block
- Sensor gap wrong or tip contaminated
- Damaged trigger wheel
How it failed
You'll notice: Alarm 600 and the engine may crank without starting, stall while running, or run only at a limited speed.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine starting, glow plugs and engine speed
- 42Unit forced to low speedOtherCheck soon
- 43Unit forced to low speed modulationOtherCheck soon
- 55Check engine speedsOtherCheck soon
- 511Engine wait to start time delay expiredOtherInformation
- 600Check crankshaft speed sensorOtherStop now
- 601Check camshaft speed sensorOtherCheck soon
- 611Check glow plug circuitOtherCheck soon
- 620No RPM detected during start attemptOtherStop now
- 642ECU forced low speedOtherInformation
Show the other 14 codesHide the other codes
- 07Check engine RPM sensorOtherStop now
- 15Check glow plugs or intake air heaterOtherCheck soon
- 16Manual start not completedOtherInformation
- 17Engine failed to crankOtherStop now
- 20Engine failed to startOtherStop now
- 33Check engine RPMOtherCheck soon
- 40Check high speed circuitOtherCheck soon
- 800Crankshaft position sensor errorOtherInformation
- 801Camshaft position sensor errorOtherInformation
- 811Glow plug circuit errorOtherInformation
- 839Engine speed errorOtherInformation
- 842Engine running in safe mode - low speedOtherInformation
- 844Engine failed to crank (engine ECU)OtherStop now
- 845Starter relay errorOtherInformation
Other Thermo King codes: Engine ECU faults (SR-2/SR-3/SR-4)
Source
Thermo King Alarm Codes - North America (thermoking.com alarm code list)
This source lists 600 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Thermo King SR-2, SR-3, SR-4 truck and trailer units and related Thermo King controllers (the families the source lists).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
