EF Logo

Develon · Hydraulic valve drivers

Develon Short-format V codes (DX225LCA table) fault codes

The DX225LCA excavator table writes machine-side faults as V210 to V230. Each line gives the controller pins and the resistance or voltage to expect with the part connected or unplugged, so these are the most testable codes in the list.

FaultCheckV210Develon · Short-format V codes (DX225LCA table)
Code shows hereFAULTV210

Where this code shows

Switch the key on and open the monitor fault or service menu on the gauge panel to see active codes.

What do these codes mean?

Develon codes V210 to V230 are all about the short-format V codes (DX225LCA table). None needs an immediate stop. Start with this check: read the code and find the pins the manual lists for that part.

How urgent are they?

None of the 20 codes here means stop now; all 20 can wait until the shift ends, but find the cause before the next one.

  • Check soon20

What should I check first?

Read the code and find the pins the manual lists for that part.

Shared checks

20 of 20

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Develon V210Pump P/V fault (V210)

    Short-format code for the pump proportional pressure-reducing valve on the DX225LCA table.· Other
    Check soon

    Causes

    • Open or shorted pump valve coil
    • Damaged wire or loose pin at CN1-10 / CN1-21
    • Chafed harness at the pump regulator
    • Controller output fault

    Checks

    1. 1Unplug the pump valve and measure the coil; the manual gives 18 ohm plus or minus 2 at 25 C.
    2. 2Check the wires from controller pins CN1-10 and CN1-21 to the valve for continuity and no short to ground.
    3. 3Inspect the connector at the pump regulator for oil and water.
    4. 4Clear the code and check whether it returns at once or only after the machine warms up.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V211Cooling fan proportional valve fault (V211)

    In the DX225LCA short-format table V211 is the cooling fan proportional valve, with no test values printed.· Lost message
    Check soon

    Causes

    • Open or shorted fan valve coil
    • Damaged fan valve connector or wire
    • Controller output fault
    • Different code table than assumed (check model)

    Checks

    1. 1Confirm your model and its code table, since V211 and V000211 are not the same part.
    2. 2Unplug the fan valve and measure its coil resistance, comparing it with the value in the manual for your model.
    3. 3Inspect the harness near the fan motor for heat and chafe.
    4. 4With the engine running warm, check the fan speed responds to a changing demand.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Develon V212Flow Control P/V

    Short-format code for the flow-control proportional pressure-reducing valve.· Other
    Check soon

    Causes

    • Fault in the flow-control proportional pressure-reducing valve or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the flow-control proportional pressure-reducing valve against the table value (R = 14 plus or minus 2 ohm at 25 C) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V213Relief Pressure Up S/V

    Short-format code for the relief-pressure-up solenoid; the boost switch on the right joystick must be on to test it.· Other
    Check soon

    Causes

    • Fault in the relief-pressure-up solenoid; the boost switch on the right joystick must be on to test it or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the relief-pressure-up solenoid; the boost switch on the right joystick must be on to test it against the table value (R = 26.2 plus or minus 2 ohm at 25 C) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V214High Speed S/V

    Short-format code for the travel high-speed solenoid; voltage is read only with the Py pressure switch on.· Other
    Check soon

    Causes

    • Fault in the travel high-speed solenoid; voltage is read only with the Py pressure switch on or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the travel high-speed solenoid; voltage is read only with the Py pressure switch on against the table value (R = 26.2 plus or minus 2 ohm at 25 C) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V215Swing Priority S/V

    Short-format code for the swing-priority solenoid; the work mode must be trenching to test it.· Other
    Check soon

    Causes

    • Fault in the swing-priority solenoid; the work mode must be trenching to test it or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the swing-priority solenoid; the work mode must be trenching to test it against the table value (R = 26.2 plus or minus 2 ohm at 25 C) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V216Reverse Fan Speed S/V

    Short-format code for the reverse fan speed solenoid.· Other
    Check soon

    Causes

    • Fault in the reverse fan speed solenoid or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the reverse fan speed solenoid against the table value (no value listed (N.A.)) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V217Starter Relay

    Short-format code for the starter relay output.· Other
    Check soon

    Causes

    • Fault in the starter relay output or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the starter relay output against the table value (battery voltage, measured while starting) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V218After Heat Relay

    Short-format code for the after-heat (glow) relay output.· Other
    Check soon

    Causes

    • Fault in the after-heat (glow) relay output or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the after-heat (glow) relay output against the table value (no value listed) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V220Front Pump Press. Sensor

    Short-format code for the front pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the front pump pressure sensor or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the front pump pressure sensor against the table value (measure with the engine stopped) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V221Rear Pump Press. Sensor

    Short-format code for the rear pump pressure sensor.· Other
    Check soon

    Causes

    • Fault in the rear pump pressure sensor or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the rear pump pressure sensor against the table value (measure with the engine stopped) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V222Hyd. Oil Temperature Sensor

    Short-format code for the hydraulic oil temperature sensor.· Other
    Check soon

    Causes

    • Fault in the hydraulic oil temperature sensor or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the hydraulic oil temperature sensor against the table value (R = 2.45 plus or minus 0.25 kohm at 25 C, 320 plus or minus 32 ohm at 80 C) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V223Water Temperature Sensor

    Short-format code for the coolant temperature sensor.· Other
    Check soon

    Causes

    • Fault in the coolant temperature sensor or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the coolant temperature sensor against the table value (no value listed (N.A.)) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V224Engine Speed Sensor

    Short-format code for the engine speed sensor.· Other
    Check soon

    Causes

    • Fault in the engine speed sensor or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the engine speed sensor against the table value (no value listed (N.A.)) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V225Fuel Level Sensor

    Short-format code for the fuel level sender.· Other
    Check soon

    Causes

    • Fault in the fuel level sender or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the fuel level sender against the table value (R = 5 plus or minus 0.25 kohm empty, 320 plus or minus 32 ohm full) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V226Alternator Potential

    Short-format code for the alternator potential (charge) input.· Other
    Check soon

    Causes

    • Fault in the alternator potential (charge) input or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the alternator potential (charge) input against the table value (V = 2 plus or minus 1 V, engine stopped) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V227Dial

    Short-format code for the engine speed dial.· Other
    Check soon

    Causes

    • Fault in the engine speed dial or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the engine speed dial against the table value (R = 1.0 plus or minus 0.3 kohm at one end, 4.0 plus or minus 1.5 kohm at the other) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V228Tps (Wheel)

    Short-format code for the throttle position sensor (wheeled machines).· Other
    Check soon

    Causes

    • Fault in the throttle position sensor (wheeled machines) or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the throttle position sensor (wheeled machines) against the table value (no value listed (N.A.)) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V229Parking Brake Press. Sensor

    Short-format code for the parking brake pressure sensor.· Other
    Check soon

    Causes

    • Fault in the parking brake pressure sensor or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the parking brake pressure sensor against the table value (no value listed (N.A.)) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Develon V230E/g Control Motor Sensor

    Short-format code for the engine control motor position sensor.· Other
    Check soon

    Causes

    • Fault in the engine control motor position sensor or its connector
    • Open, shorted or chafed wiring
    • Supply or ground problem to the circuit

    Checks

    1. 1Check the engine control motor position sensor against the table value (no value listed (N.A.)) with the connector in the state the manual states.
    2. 2Inspect the connector and wires for water, corrosion and chafe, then retest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Read the code and find the pins the manual lists for that part.
  2. 2Measure the part resistance with the connector unplugged against the listed value (25 degrees C).
  3. 3With the connector plugged in and key on, measure the voltage at the controller pins where the table gives one.
  4. 4Inspect the harness between controller and part for chafe, water and corrosion.

Causes

  • Open or shorted coil or sensor
  • Chafed wire or damaged connector
  • Blown fuse or loose pin in the supply path
  • Controller output or input fault

When to stop

You'll notice: The monitor shows a V code, and the affected function (pump flow, fan, travel, starting, fuel gauge) misbehaves.

Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.