John Deere · Main controller (MCZ) - options
John Deere Fault Code MCZ 11458.02
Selector valve solenoid not detected
What does John Deere code MCZ 11458.02 mean?
The MCZ cannot find the selector valve solenoid used with the auxiliary high-flow kit. If no high-flow kit is installed, the code can be cleared. Urgency: information - a reminder or status message. Check first: check whether the machine has an auxiliary high-flow kit fitted.
- MCZ
- Which controller reports it
- 11458
- What is at fault
- .02
- How it failed
Can I keep running with it?
Information
A reminder or status message. Nothing is failing yet.
What should I check first?
Check whether the machine has an auxiliary high-flow kit fitted
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- No high-flow kit installed but the controller is set up to expect one
- Unplugged or broken wire to the selector valve solenoid
- Failed selector solenoid coil
- Controller configured for the wrong option set
How it failed
You'll notice: The MCZ cannot find the selector valve solenoid for the high-flow auxiliary kit.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Dig, regeneration and travel speed solenoids
1 other code on this part is also lost message (MCZ 11457.02). When they show together, start at the wiring and connector they share.
- MCZ 11407.043-Spool solenoid valve unit (SG) feedback low inputOpen circuitCheck soon
- MCZ 11428.024-Spool solenoid valve unit (SD) abnormal feedbackOtherCheck soon
- MCZ 11428.034-Spool solenoid valve unit (SD) feedback high inputReal conditionCheck soon
- MCZ 11428.044-Spool solenoid valve unit (SD) feedback low inputReal conditionCheck soon
- MCZ 11457.022-speed activation solenoid not detectedLost messageInformation
- MCZ 11458.02Selector valve solenoid not detectedLost messageInformation
- MCZ 11948.02Power dig solenoid feedback current abnormalOtherCheck soon
- MCZ 11948.03Power dig solenoid feedback current highShorted highCheck soon
- MCZ 11948.04Power dig solenoid feedback current lowOpen circuitCheck soon
Show the other 14 codesHide the other codes
- MCZ 11402.02Dig regenerative solenoid feedback current abnormalOtherCheck soon
- MCZ 11402.03Dig regenerative solenoid feedback current highReal conditionCheck soon
- MCZ 11402.04Dig regenerative solenoid feedback current lowReal conditionCheck soon
- MCZ 11403.02Arm regenerative solenoid feedback current abnormalOtherCheck soon
- MCZ 11403.03Arm regenerative solenoid feedback current highReal conditionCheck soon
- MCZ 11403.04Arm regenerative solenoid feedback current lowReal conditionCheck soon
- MCZ 11404.02Power dig solenoid feedback current abnormalOtherCheck soon
- MCZ 11404.03Power dig solenoid feedback current highShorted highCheck soon
- MCZ 11404.04Power dig solenoid feedback current lowOpen circuitCheck soon
- MCZ 11405.02Travel speed solenoid feedback current abnormalOtherCheck soon
- MCZ 11405.03Travel speed solenoid feedback current highReal conditionCheck soon
- MCZ 11405.04Travel speed solenoid feedback current lowReal conditionCheck soon
- MCZ 11407.023-Spool solenoid valve unit (SG) abnormal feedbackOtherCheck soon
- MCZ 11407.033-Spool solenoid valve unit (SG) feedback high inputShorted highCheck soon
Related on Equipments Finder
Source
Excavator Fault Codes - John Deere excavators fault codes list (MCZ/ECU/DSZ)
This source lists MCZ 11458.02 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere G-series excavators (210G/210GLC and 350G class) with MCZ main controller; confirm against serial number.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
