John Deere · Engine control unit (ECU) - PowerTech engine
John Deere Fault Code ECU 000110.00
Coolant temperature high
What does John Deere code ECU 000110.00 mean?
The ECU sees engine coolant temperature above the limit. The operator may see an overheat warning and a derate, and running on can crack the head or blow the gasket. Urgency: stop now - shut down and fix before working on. Check first: let the engine idle to cool and check the coolant level when cold.
- ECU
- Which controller reports it
- .00
- Data above normal, most severe
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Let the engine idle to cool and check the coolant level when cold
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- Coolant level low from a leak
- Radiator or cooler blocked with debris
- Thermostat stuck closed or the water pump failing
- Fan or fan drive not working
How it failed
You'll notice: The ECU sees engine coolant temperature above its limit.
Shorted highRead from how the source describes the code
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine coolant, intake air and fuel temperature
2 other codes on this part are also shorted high (ECU 000105.00, ECU 000174.00). When they show together, start at the wiring and connector they share.
- ECU 000105.00Intake air temperature highShorted highCheck soon
- ECU 000105.04Intake air temperature signal faultErratic or implausibleCheck soon
- ECU 000105.15Intake air temperature high: cooling system dustLost messageCheck soon
- ECU 000105.16Intake manifold air temperature drastically highLost messageCheck soon
- ECU 000110.00Coolant temperature highShorted highStop now
- ECU 000110.03Engine coolant temperature signal highOtherCheck soon
- ECU 000110.04Engine coolant temperature low voltage inputShorted lowCheck soon
- ECU 000110.15Engine coolant temperature slightly highLost messageCheck soon
- ECU 000110.16Engine coolant temperature high: cool downLost messageCheck soon
Show the other 11 codesHide the other codes
- ECU 000110.17Engine coolant temperature low: warm upLost messageCheck soon
- ECU 000111.01Coolant level lowReal conditionStop now
- ECU 000111.07Coolant loss detectedReal conditionStop now
- ECU 000111.17Coolant level low (moderate)OtherCheck soon
- ECU 000111.18Coolant level low: moderately severe levelOtherCheck soon
- ECU 000174.00Fuel temperature highShorted highCheck soon
- ECU 000174.03Fuel temperature sensor inaccessibleOtherCheck soon
- ECU 000174.04Fuel temperature signal voltage lowShorted lowCheck soon
- ECU 000174.16Fuel temperature increasedLost messageCheck soon
- ECU 003587.05Cold start aid solenoid open circuitOpen circuitCheck soon
- ECU 003587.06Cold start aid solenoid short circuitLost messageCheck soon
Other John Deere codes: Engine control unit (ECU) - PowerTech engine
Related on Equipments Finder
Source
Inside the Yard - John Deere fault codes list (ECU engine codes)
This source lists ECU 000110.00 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere PowerTech engines; code list comes from tractor-based sources, confirm for your machine.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
